It's in the front of the engine underneath the starter Mark helpful Content submitted by Users is not endorsed by CarGurus, does not express the opinions of CarGurus, and should not be considered reviewed, screened, or approved by CarGurus.
Full Answer
What is a crankshaft position sensor?
Crankshaft – Camshaft Position Sensors serve essentially the same purpose as; the ignition pickup and trigger wheel in an electronic distributor. The only difference is the basic timing signal is read off the crankshaft or balancer, instead of the distributor shaft.
How do I get a repair guide for a PT Cruiser?
Access our PT Cruiser 2006-2007 Removal & Installation Repair Guide Non-Turbo Models by creating an account or signing into your AutoZone Rewards account. Once you sign in, follow these instructions to access our Repair Guides. Add your vehicle in Manage My Vehicles.
What to do if your camshaft position sensor is bad?
If no signal comes out of the sensor, most likely the sensor is bad. Remove the sensor and inspect it for signs of physical damage or contamination. If you can’t find anything wrong with the Crankshaft – Camshaft Position Sensor or its circuit; it’s possible you may have an intermittent failure or a failure in a related component.
How do I know if my tire pressure sensor is bad?
In most cases, you’ll see a fluctuating signal between 0.3 volts and 1 volt. If there’s no signal, you have a bad sensor. First, identify the power, ground, and signal wires using your vehicle repair manual. Next, test the sensor circuit by setting your multimeter to “DC volts.”
Where is crankshaft sensor located?
The sensor is at either the front or the back of the crankshaft, so it's usually located either on the transmission bellhousing or behind the crankshaft pulley. There should be a small air gap, usually about a millimeter or two, between the sensor and the reluctor.
Where is the crank sensor located on a 2008 PT Cruiser?
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor.
Where is the camshaft sensor on a 2007 PT Cruiser?
0:223:03How to Remove and Replace a Camshaft Position Sensor - YouTubeYouTubeStart of suggested clipEnd of suggested clipOkay so your character position sensor on these cars is on the left side of the engine or theMoreOkay so your character position sensor on these cars is on the left side of the engine or the driver's side and it's that guy right there.
Where is the crankshaft position sensor on a 2005 PT Cruiser?
0:104:492005 PT Cruiser crankshaft sensor replacement - YouTubeYouTubeStart of suggested clipEnd of suggested clipAre we're doing as a taken the crank sensor is out on this 2005 PT Cruiser I guess if you have smallMoreAre we're doing as a taken the crank sensor is out on this 2005 PT Cruiser I guess if you have small hands it's right underneath the starter right there it directly below it.
How much does it cost to replace a camshaft sensor on a PT Cruiser?
The Best in Auto Repair The average cost for a Chrysler PT Cruiser camshaft position sensor replacement is between $26 and $33. Labor costs are estimated between $26 and $33.
How do you fix a crankshaft sensor?
0:361:54Crankshaft Position Sensor: How it Works & How to Fix [1 Method Save ...YouTubeStart of suggested clipEnd of suggested clipPosition sensor first carefully remove the crankshaft. Position sensor from the vehicle visuallyMorePosition sensor first carefully remove the crankshaft. Position sensor from the vehicle visually inspect the sensor to make sure it hasn't been contaminated by a leak from another engine component.
Will a crankshaft sensor make a car stall?
If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall. This is usually a sign of a wiring problem.
Where is camshaft position sensor bank1?
2:007:39Replacing Bank 1 Camshaft Position Sensor On 350Z - P0340 - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf you look back right here that connector right there that's the cam chef there's a sensor so likeMoreIf you look back right here that connector right there that's the cam chef there's a sensor so like I said we're right behind the engine.
How do you reset a camshaft position sensor?
Unfortunately, there's no way to reset a camshaft position sensor. If you're having camshaft issues (check engine light on, acceleration trouble, sputtering and stalling, etc.), you'll have to replace the part entirely.
How much is a crankshaft sensor on a 2005 PT Cruiser?
The average cost for a Chrysler PT Cruiser crankshaft position sensor replacement is between $195 and $204.Labor costs are estimated between $35 and $44 while parts are priced at $160.This range does not include taxes and fees, and does not factor in your specific model year or unique location.More items...