beko washing machine faults problems

1. Washer Not Draining: Beko washers can be difficult to drain. Usually, this is not a problem because the lint trap will catch the majority of the lint.
2. Beko Washer Leaking Water: This is the most common problem with Beko washers. ...
3. Washing Machine Won’t Start: There can be several reasons for this problem. First, make sure the washer is plugged into a good electrical outlet.
4. Beko Washing Machine Stuck Cycle: This problem occurs when the machine gets into a state where it won’t start a cycle until you use a key or other external ...
5. Washer Runs Too Fast: First, check to see that the washer is plugged in and that the fuses in the circuit where the washer is located are not blown.
Beko Washer Noise: Noise is a common problem with many washing machines. ...
The door won’t open: This problem is often caused by corrosion. To fix it, you need to clean the washer with a brush and some solvent.
The machine is not filling with water: Most probably you are using the wrong amount of water. Either too much or not enough. ...

Full Answer

How to reset a Beko washing machine?

• Faulty pressure switch: there is a pressure switch inside which tells the machine when the cycle is over. ...
• Faulty interlock: if that doesn't help, your interlock may be at fault. ...
• Faulty hinges in a top loading washing machine: the hinges on your washing machine's lid may have worn down. ...

How to cure dispenser problems in a Beko washing machine?

To test that your water supply is strong enough:

• Turn on the cold tap situated nearest to where your Beko washing machine is installed.
• Measure the water flow rate. At least one litre in seven seconds is required.
• If the flow rate is less, you need a plumber to check your water line.

How reliable is Beko?

The warranty is subject to the following conditions:

• You need to register your product
• The product must be in normal household conditions
• The freezer or fridge must be bought through an authorized dealer or reseller
• The warranty is not transferable

How to replace the heater on a Beko washing machine?

• The machine will be displaying the error
• Check the door is shutting correctly.
• Strip down the machine to get access to the door interlock.
• Check wiring harness for signs of burnt connections or broken wires.
• Replace door lock is faulty.
• Reassemble the washing machine test the machine and make sure it starts. If all is ok problem is fixed

How do I reset my Beko washing machine?

If your Beko washing machine won't start, there's an easy reset process to follow:Locate the start, pause and cancel buttons.Press them all down at the same time for around 3-5 seconds.Your machine should now be reset.

What is the most common problem with washing machine?

7 Common problems with washing machineWashing machine not starting. ... Washing machine is noisy. ... Excessive vibrations during operation. ... Washing machine making noise when draining or not draining at all. ... Washing machine over-filling or under-filling. ... Washing machine not spinning. ... Water leaking from soap drawer.

What are the common faults and problems of washing machine?

10 Most Common Washing Machine ProblemsIt Bounces Around. ... It's Noisy. ... Clothes Are Getting Ripped. ... Improper Or Slow Draining. ... My Washing Machine Won't Spin. ... There's No Water. ... The Door Won't Open. ... It's Smelly.More items...

Is there a reset button on a Beko washing machine?

Try resetting the appliance by pressing and holding the start/pause/cancel button for three seconds.

How do you diagnose a washing machine problem?

Washer Troubleshooting GuideCheck that the washer is plugged in securely.Check the circuit breaker or fuse box.Test the outlet for current.Check that the water supply valves are turned on.Inspect the filter screens.Test for overheating.Test the water level switch.Test the timer control.More items...

What are the four trouble symptoms of washing machine?

Common Washing Machine Problems and SolutionsVibrating Washer.Leaky Washer.Noisy Washer.Washer Won't Run.Washer Won't Drain.Detergent Won't Dispense.Smelly Washer.

Is it worth repairing my washing machine?

As a general rule, if it costs less than 50% of the price of a new washing machine to repair your old one, you should choose the repair option. But, you should also consider whether or not there is a warranty coverage on your washer and think about economic realities.

How long should a wash machine last?

around 10 yearsWashing machines, on average, last around 10 years, according to Consumer Reports.

Why won't my washing machine finish its cycle?

Some of the most common faults that will make your washer stop mid cycle include thermostat failure, problems filling up with water for the rinse cycle, or even pump problems that prevent your washer from draining. One thing that you can check yourself is the lid switch.

How do you run diagnostics on a Beko washing machine?

0:043:56Beko wmb 7, 8, 9 Series washing machines diagnostic & test modeYouTubeStart of suggested clipEnd of suggested clipSo we'll just do it again press the start button turn the machine on with the dial set to the 12 o'MoreSo we'll just do it again press the start button turn the machine on with the dial set to the 12 o'clock position. You will either now see an error code or a number will be displayed.

How do I find my Beko error code?

The Beko error code system is very simple it goes from E1 to E18, if you can correct the error yourself then you'll simply need to hold down the start button to clear the error code. Remember though if you can't correct the error or aren't confident enough to attempt it then we can help!

Why is my Beko washing machine not spinning or draining?

The most probable cause is a clogged pump filter. The pump filter should be cleaned every three months or when it's clogged. This filter is installed to catch foreign objects like buttons or coins, and to prevent these items from entering the drain hose.

1. Washer Not Draining

Beko washers can be difficult to drain. Usually, this is not a problem because the lint trap will catch the majority of the lint. However, if there is a clog in the drain hose, it can prevent the water from draining completely.

2. Beko Washer Leaking Water

This is the most common problem with Beko washers. It happens because the rubber O-rings inside the tub (the part that holds the wash water) get soft after years of use and eventually lose their seal against the inner sides of the tub.

4. Beko Washing Machine Stuck Cycle

This problem occurs when the machine gets into a state where it won’t start a cycle until you use a key or other external force. There are several possible causes:

5. Washer Runs Too Fast

First, check to see that the washer is plugged in and that the fuses in the circuit where the washer is located are not blown.

6. Beko Washer Noise

Noise is a common problem with many washing machines. Some of the causes of noise include:

8. The machine is not filling with water

Most probably you are using the wrong amount of water. Either too much or not enough.

Why won't my Beko washing machine open?

If your Beko washing machine door won't open, you potentially have a very messy problem on your hands. The first thing you'll need to do is make sure that your machine isn't still full of water:

Why is my Beko washing machine not spinning?

Beko washing machine not spinning. A non-mechanical problem which might be affecting your machine's ability to spin might be the type and size of load you've placed inside it. Try not to overload or chronically underload your machine.

How to clean a blocked water filter?

Be aware though that when you open the housing there may be water inside. You can drain the water out using a tube, put a container down to catch it and/or get a bunch of towels ready. Rinse the filter and replace it.

What is a fault in a pressure switch?

Faulty pressure switch: there is a pressure switch inside which tells the machine when the cycle is over. If this is malfunctioning, unplugging your machine from the wall for 10 minutes should fix your problem. This will reset it properly. Faulty interlock: if that doesn't help, your interlock may be at fault.

What to do if the "on again off again" approach doesn't work?

If the simple “on again off again” approach doesn't work, you'll probably need an engineer. Otherwise, you'll be left trying to wedge or wangle the door open, which is an easy way to break it.

Is a washing machine a modern convenience?

Washing machines are amazing modern conveniences. But they're not immune to faults and malfunctions...