How do I get a whirlpool manual for my appliance?
Downloading manuals is also a convenient way of obtaining a back-up in case your original document goes missing. Enter your appliance’s model number above to obtain an official Whirlpool manual. For help with Whirlpool® troubleshooting, service or How To guides, visit the Whirlpool Customer Care portal.
Why do I need an official Whirlpool® manual?
Whirlpool ® manuals can help you get the most out of your appliance, and provide important information about parts and accessories. Downloading an official Whirlpool® manual from our website is also a convenient way of obtaining a back-up in case your original document goes missing.
How do I contact Whirlpool customer service?
Need Help? 1-866-698-2538 U.S. 1-800-807-6777 Canada. Whirlpool Customer Service. 553 Benson Rd. Benton Harbor MI 49022
What is the temperature range for a whirlpool refrigerator?
The factory recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer. Refrigerator set point range: 33°F to 45°F (0°C to 7°C). Freezer set point range: -5°F to 5°F (-21°C to -15°C).
How do I reset my Whirlpool water heater?
Steps To Reset Your Whirlpool Water HeaterOpen The Water Heater. Turn off the power from the breaker panel. ... Take Out The Cover Plates. ... Pull Out The Insulation Pad. ... Press The Reset Button. ... Reassemble The Water Heater. ... Turn The Power Back On.
Does a Whirlpool water heater have a reset button?
The thermal switch can trip if the water heater is not getting enough air. Press the small reset button in the center of the thermal switch. If it's tripped, you may be able to hear it click. Even if you do not hear the thermal switch click, try lighting the pilot using the instructions on the water heater's label.
How do I use my Whirlpool water heater?
1:253:43Whirlpool Water Heater Review And Lighting Instructions - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere's how you light the pilot. But all you do is you turn that about the video you turn that littleMoreHere's how you light the pilot. But all you do is you turn that about the video you turn that little knob to pilot hold it down and press the igniter.
How do I adjust the temperature on my Whirlpool smart water heater?
Set both thermostats to 120°F. If higher temperatures are required turn the water temperature dial clockwise ( >>) to increase the temperature. (Turn the dial counter clockwise ( << ) to decrease the temperature.) Adjust both thermostats to the same temperature setting.
Why is my water heater not heating up?
If an electric water heater is not producing hot water, it could be a simple problem like a blown fuse or tripped circuit breaker. Additionally, some electric water heaters have a circuit-style safety switch located near or on the thermostat.
Why is my hot water not working?
A water heater that produces no hot water may not be getting power, may have a tripped limit switch, or may have one or more failed heating elements. First, check the water heater's circuit breaker in the service panel to make sure it hasn't tripped. If the breaker has tripped, switch it off, then switch it back on.
How do you turn on a whirlpool hot water heater?
2:145:46How to light pilot on water heater - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo before you even start ten minutes in the off position. Once. We start right now we're gonna pushMoreSo before you even start ten minutes in the off position. Once. We start right now we're gonna push in that button. And we're gonna start pushing our zapper will do this for 90 seconds.
How do I turn on the water heater?
0:503:06How to Reignite a Hot Water Heater - YouTubeYouTubeStart of suggested clipEnd of suggested clipNext go back to the gas valve adjustment dial look for the settings that include on/off. And pilotMoreNext go back to the gas valve adjustment dial look for the settings that include on/off. And pilot these will be printed on the dial or next to the dial turn the dial to the pilot setting.
How do you start a whirlpool gas water heater?
Make sure the gas supply valve is turned ON. When lighting the pilot, make sure the knob on the gas control valve is fully pushed in. Keep the knob pushed in while repeatedly clicking the spark igniter button. Hold the knob in and click the igniter button repeatedly for 90 seconds.
How do I make my hot water heater hotter?
0:050:48How To Make Your Hot Water HOTTER - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the insulation. Forward it's already perforated at the bottom. And then right there you'll seeMorePull the insulation. Forward it's already perforated at the bottom. And then right there you'll see a dial where you can adjust your temperature. You can turn it up to 150 degrees or down to 120.
How do I adjust my thermostat?
0:091:42How To Adjust Your Thermostat - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo right now we have it set to automatic. If you ever wanted to be adjusted you simply just press upMoreSo right now we have it set to automatic. If you ever wanted to be adjusted you simply just press up on the temperature. Make sure to hit done. And the unit will acknowledge.
What temperature should water heater be set at?
120 degrees Fahrenheit is the safety recommendation against scalding, but 140° is the common default setting. Most experts agree that anything below 120 degrees creates a risk for bacteria to develop inside your water heater from stagnant water, such as legionella that causes Legionnaire's disease.
Where is the reset button on a hot water heater?
1:123:17HOW TO RESET ELECTRIC WATER HEATER - YouTubeYouTubeStart of suggested clipEnd of suggested clipHere is our reset button this one is red we're going to press the button and sometimes the button isMoreHere is our reset button this one is red we're going to press the button and sometimes the button is black.
Is there a reset button on a gas water heater?
The reset button is often red and located near the thermostat or behind a metal panel that is removable on the unit. When you find it, push the reset button and then release it. There may be a lower thermostat button also known as a second reset button.
How do I reset the thermostat on my electric water heater?
Somewhere on your electric water heater, you'll find a reset button. It's usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.
How do you unlock a whirlpool smart water heater?
1. Unlock the water heater's user interface (if it is locked). To do so, touch the lock button for at least 5 seconds. The Lock icon will disappear from the screen.
How often should I drain my water heater?
The water heater should be drained if being shut down during freezing temperatures. It is recommended that the tank be drained, and fl ushed every 6 months to remove sediment which may buildup during operation. To drain the tank perform the following steps:
What happens when a water heater anode is depleted?
Once the anode is depleted, the tank will start to corrode, eventually developing a leak. Certain water conditions will cause a reaction between this rod and the water. The most common complaint associated with the anode rod is a “rotten egg smell” produced from the presence of hydrogen sulfide gas dissolved in the water.