If your Whirlpool washing machine won’t start, here are the problems you should look for… 1. Drive Belt Is Worn The belt is looped around the motor shaft and tub. If this belt breaks or gets damaged, the machine will not be able to start a wash cycle.
Full Answer
Why is my Whirlpool washing machine not starting?
Whirlpool Washer Won’t Start – Troubleshoot and Diagnosis
- Incoming Power Problem. When something goes wrong with your Whirlpool washer, it can feel like the world is falling apart! ...
- Washer Needs Hard Reset. ...
- Whirlpool Washer Start Button Stuck. ...
- Control Lock is Turned ON. ...
- Incorrect Washer Settings. ...
- Blown Thermal Fuse. ...
- Faulty Lid Switch. ...
- Defective Control Board. ...
- Broken Timer. ...
- Faulty Motor. ...
How do you reset a whirlpool washer?
To do it, follow these instructions below:
- Go to your display pad and touch any button you see there. ...
- Choose a cycle and press “START.” This might sound crazy, but yes, it’s part of the reset function. ...
- If the error comes back, disconnect your washing machine from the power source. ...
- Plug it back in, and choose any cycle. ...
- If it still hasn’t reset, repeat steps three and four. ...
How to repair my Whirlpool duet washer?
How do I fix my f28 error on my Whirlpool Duet washer?
- Unplug the electrical cord from the wall outlet.
- Open the detergent tray on the top of the washer and locate the Phillips screws that hold it in place.
- Remove the detergent tray screws using a Phillips screwdriver and pull off the tray.
- Find the control console unit reset lever and pull it toward you.
Why your Whirlpool washer door locked light is flashing?
Whirlpool washer door locked light flashing
- Common issues that cause whirlpool washer door locked light flashing
- Problem in the lid switch. Switch failure is one of the typical problems when the whirlpool washer door locked light flashing. ...
- Check actuator motor. There is maybe some issue with the motor. ...
- Issue in drain pump. ...
- Need to check the hose. ...
- Malfunctioning Door Switch. ...
Why does my Whirlpool washer not want to start?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home's main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.23-Feb-2021
Why does my washer turn on but not start?
First, make sure the power is on and that the machine is plugged in. You should check the outlet to make sure it's working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated.
How do you reset a Whirlpool washing machine?
Follow these steps to reset your Whirlpool washer:Turn the washing machine off using the control panel.Unplug the washing machine.Wait three minutes.Plug the washer back in, and wait thirty seconds before turning the washer on.01-Nov-2021
Is there a reset button on a Whirlpool washing machine?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I start my Whirlpool washing machine?
0:081:27Whirlpool Washers - How to use your washing machine? - YouTubeYouTubeStart of suggested clipEnd of suggested clipFollow these simple instructions to use your whirlpool washer. First add the detergent at the bottomMoreFollow these simple instructions to use your whirlpool washer. First add the detergent at the bottom of the basket. We recommend you use liquid detergent for automatic washing machines.
Is there a reset button on a washing machine?
Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it. Although not usually a button, programmable washing machines might have a reset function or position to clear a program problem.29-Dec-2018
How do I put my Whirlpool washer in diagnostic mode?
0:000:48Whirlpool Washer Test/Diagnostic Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou press the start button this will allow your washing machine to go into the test or diagnosticMoreYou press the start button this will allow your washing machine to go into the test or diagnostic mode and this will isolate if you're having any issues the water will run the spin cycle will engage.
How do I reset my washing machine cycle?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do you reset a washing machine sensor?
1:243:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
Does my Whirlpool washing machine have a fuse?
The lid switch is on the top of the washer lid opening. Plug the washing machine in. The lid switch needs to be removed from the machine before the two screws that hold it in place can be removed. The fuse should be located.
Why does my Whirlpool washer stop spinning?
The most common reason a Whirlpool top-loader washer stops spinning is a faulty lid switch. The lid switch is a safety measure that prevents the washer from spinning while the lid is open. The lid switch on most top-loader washers can be activated manually using a screwdriver or pencil to push it to simulate the lid being closed. You should also be able to hear the lid switch click when you close the lid. If you cannot, it probably needs to be replaced.
Why won't my washer spin?
Like the lid switch on top-loader washers, if the door lock on front-loader washers is faulty, the washer will not spin. The door lock can be checked for a mechanical fault by inspecting it closely and paying attention to it as you open and close the door. To see if the door lock is faulty due to an electrical fault, you will need to test it with a multimeter. If the door lock is broken, it is likely unrepairable and will need to be replaced.
What happens if the motor coupling breaks?
If the motor coupling breaks, the washer will not spin. When repairing the motor coupling, it is recommended that you do not remove the clutch, as this can be difficult to put back after the brake disengages. Follow these steps to repair the motor coupling: Disconnect the washer from the power source.
Why is my washer not spinning?
Another common reason for a washer not spinning is a problem with the drive belt . The drive belt is responsible for rotating the tub. Over time, the drive belt can become loose or break, which causes the washer not to spin.
Why do clothes need to be placed evenly around the agitator?
If there is an imbalance, perhaps because clothes have gotten caught up on one side of the drum, the motion of the washer is disrupted, which results in a subpar spin cycle. For the same reasons, the washer itself also needs to be balanced.
Does Whirlpool have a spin cycle?
Their range of models features top-loaders, front-loaders, and washer-dryer combinations. Occasionally, even the highest quality models may have an issue with the spin cycle. The most common causes of the issue can be fixed by following this guide.
Why won't my washer recognize when the door is shut?
If the lid latch assembly itself is faulty or if its wire connectors have gone bad, the washing machine will not recognize when the door is shut, and it will not run as a result.Replacing the lid latch assembly involves shutting off the water supply lines and unplugging the washing machine.
How to replace a washer lid latch strike?
It can also prevent a user from running the appliance.The only tool needed to replace the lid latch strike is a screwdriver. The process is quick and simple. First, make sure the washing machine is unplugged from power and the gas supply. Open the door to get access to the lid latch strike on the side of the door.
Why won't my washer open?
When the switch comes in contact with the strike, it locks the lid and signals the control panel to begin a wash cycle. The plastic strike can crack, break or become misaligned with wear and tear or if the lid is slammed down. When this happens, it may be unable to engage the lid switch or leave the washer door locked, won’t open.
How to bypass a Whirlpool top load washer lid?
If your Whirlpool top load washer won’t unlock, a magnet can bypass the lock to open the lid. Unplug the washer and move it away from the wall. Remove the top panel by pushing in its retaining tabs ...