Full Answer
How to install a distributor and set initial timing?
Unplug the electrical connector and, if your model has it, the vacuum advance hose from the distributor. Plug the hose with a small screw and don’t remove the plug until you have adjusted ignition timing. Detach the distributor cap. On some models you can detach the cap without disconnecting the spark plug wires.
How to install and set a Vortec distributor?
How to Install an Engine Ignition Distributor, Set Timing, Select Gear, Find Top Dead Center http://www.jegs.com/c/Ignition-Electrical/10359/10002/-1-----...
How to adjust a distributor?
Adjust while the engine is at idle speed. Grab the distributor firmly and rotate it slowly to one side or the other. Continue rotating until the timing mark is in the correct position. Align the timing marks by continuing to move the distributor and checking with your timing light.
How to change or assign a preferred distributor?
- Have a product that flies off the shelves all on its own. Consumers can’t get enough of it. Distributors loooove Suppliers with “hot” brands. ...
- Pay a rep a ridiculous amount of money in the form of an incentive to push the sale.
- Consistently help the rep earn commissions and incentives by executing key activities in the field that help them sell. ...
What hand do you use to rotate a distributor?
The direction your fingers point is the direction of rotor movement. On a Chevy distributor, you would use your left hand, and on a Ford you’ll use your right hand. This is a cool little trick you can use on any distributor to determine its rotation. ….
What happens if you accidentally switch the wires on a Hei distributor?
If the wires are accidentally switched, the engine will not be happy. Before we try to start the engine, be sure the distributor is connected to switched power. With an HEI distributor, there is a three-wire inboard connector between the HEI module and the cap.
What happens if the distributor is off by more than one tooth?
If the rotor is not pointing at Number One, you could twist the distributor body, but if it is off by more than one tooth, this will require turning the distributor body too far. Instead, you will need to remove the distributor and repeat the previous process as the rotor is not in the correct position.
What is the number on the left side of a Ford cylinder?
The left side is numbered 1-3-5-7 , and the right side is 2-4-6-8. Ford does it differently. Ford numbers its cylinders with Number One on the right front, numbered on the right side 1-2-3-4 with the left side 5-6-7-8. Other manufacturers number their cylinders differently, so you should check online if you’re not sure.
Where is the vacuum advance canister located?
Position the distributor so that the vacuum advance canister is located on the passenger side of the engine pointing roughly forward. If the rotor is not pointed close to the Number One mark, pull the distributor and re-position the rotor until it comes close.
How to rotate distributor?
You may need to rotate the distributor by hand when setting the ignition time. Install the distributor cap. Align the notch or tab on the cap with the notch or tab on top of the distributor body. Wiggle the cap from side to side to make sure the cap is sitting correctly on the distributor. The cap shouldn't wobble.
Where do you find the timing light on a car?
Make sure you know where the timing marks on your vehicle are located. In most cars, you'll find the marks on the crankshaft pulley or flywheel.
How to tell if a distributor shaft is helical?
If your distributor shaft has a helical drive gear, as you pull the distributor out, the shaft will rotate a few degrees clockwise or counterclockwise. You'll notice this by watching the rotor as you pull the distributor out. Notice the direction and the amount of any rotation on the rotor.
How many leads does a timing light have?
Connect the timing light. The timing light has three leads. Two of the leads connect to the battery and the third lead may connect directly to the metal connector of number one spark plug wire or clipped around the same wire without unplugging it from the spark plug. Consult the tool's operating manual, if necessary.
Where are the drive lugs on a distributor?
Some distributors come with drive lugs at the base that should align with the drive grooves in the camshaft. Once the distributor is in place, make sure is fully seated against the engine block. Double check that the aligning marks on the engine, distributor, and primary rotor mark, are all aligned.
How to remove air cleaner distributor?
Remove any components that block access to your distributor: depending on your model,the air cleaner assembly, electrical connectors, wires, or hoses. Label wires, connectors or hoses, if necessary, so that you can reinstall them correctly.
How to get a starter to move when you hit the starter?
Everyone is giving you good advise, you have no way of knowing how far it moved when you hit the starter so the only way to get it right is to start from scratch. Bring number one up on compression stroke (put your thumb over the number one spark plug hole while someone bumps the starter (or better yet, use a breaker bar to turn the crank) and when you start feeling compression look at the timing mark on the damper and bring it around until the marks line up. Now you can drop the distributor back in and pointing to number one.
What to do if your oil pump is not on TDC?
If it wasn't on TDC when you pulled the distributor and you turn the crank to get it to TDC, remember that the oil pump drive may need to be turned with a long screwdriver to get it lined up. Then the distributor will drop right in place.