Full Answer
How does the starter work on a GMC Sierra?
First, the ignition switch sends electrical current from the battery to the starter solenoid. The solenoid then forces the gear in the starter housing to engage the engine. When the starter motor turns on and spins the gear, the engine roars to life. If any of these stop working, it means the starter won't turn over in your GMC Sierra.
Where is the starter located on a Ford Ranger?
The starter is located underneath the engine on the front passenger's side. On V8 engines, there is a bell cover housing that must first be removed to access the starter.
Why won't my GMC Sierra start after replacing battery?
If the Sierra does not start after replacing or charging the battery, move to the next step. Turn the headlights on and then turn the ignition key to the "On" position. If the headlights dim, the ignition switch sends electricity to the starter motor and solenoid.
How do you wire a starter solenoid to an ignition switch?
The wire on the left connector connects to the ignition switch. The wire on the right connector connects to the starter motor. Place the blade of a screwdriver across both contacts to short out the starter solenoid. This makes a direct connection between the starter motor and the ignition switch.
Where is the starter located on a GMC truck?
0:347:46How To Replace Starter on Chevy/GMC/Cadillac Trucks 2007YouTubeStart of suggested clipEnd of suggested clipThe starter bolts to the passenger side of the engine was held in with two vertical bolts remove theMoreThe starter bolts to the passenger side of the engine was held in with two vertical bolts remove the two vertical mounting bolts. 13-millimeter now pull these wires away from the back of the starter.
Where is the starter located on a 2005 Chevy Silverado?
0:006:22How To Replace Starter On 1999-2006 Chevrolet Silverado ...YouTubeStart of suggested clipEnd of suggested clipWe have to jack stands on the frame of the vehicle. Which are right there.MoreWe have to jack stands on the frame of the vehicle. Which are right there.
Where is the starter motor located?
The starter motor is attached to end of the crankshaft via a flywheel and a pinion gear. When the ignition is turned the starter motor activates and an electromagnet inside pushes a rod out with the pinion gear. This rotates the flywheel and the engine is turned over.
Where is the starter on a 2004 GMC?
0:512:55GMC YUKON 2004 STARTER REMOVE INSTALL CHEVROLET ...YouTubeStart of suggested clipEnd of suggested clipRight up top. And this is on the passenger. Side right next to the bell housing. All right beyondMoreRight up top. And this is on the passenger. Side right next to the bell housing. All right beyond the oil pan.
How do you jumpstart a starter?
1:035:14How To Test A Car Starter With A Screwdriver And Jumper Cables!YouTubeStart of suggested clipEnd of suggested clipAnd what you want to do is you want to jump this to the s part of the small stud. Okay now once youMoreAnd what you want to do is you want to jump this to the s part of the small stud. Okay now once you do this you're activating a solenoid and a starter. And you should see the gear pop out and spin.
How do you tap a starter to make it work?
1:453:12Life Hack That Will Make a Dead Car Start Every Time - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut an even better method is if you have another person there while the other person holds the keyMoreBut an even better method is if you have another person there while the other person holds the key in the start position you tamp the starter.
How do you know if a starter motor has gone?
Still, look for these seven symptoms that your starter is going bad.#1: Engine Won't Turn Over. ... #2: Noise - Clicking, Grinding, or Whirring. ... #3: Intermittent Issues Starting the Vehicle. ... #4: Starter Stays On After Starting. ... #5: Smoke. ... #6: Starter Engages But Motor Won't Start. ... #7: Battery.
How do I know if my starter motor needs replacing?
Common Signs your Car Needs a New Starter MotorLoud Clicking Noise. A single loud click or a series of clicks that occur when you turn the key is a strong indicator of starter motor trouble. ... Whirring Noise. ... Buzzing Sounds. ... Grinding Noises.
How do you test a starter to see if it's good?
9:5514:58How to Test and Troubleshoot a Starter Problem - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe positive cable goes on its starter. Then we're to crank the engine the positive side crankingMoreThe positive cable goes on its starter. Then we're to crank the engine the positive side cranking test you don't want to see any more than 0.7 volts here. So if you see more than 0.7 volts here then.
How long does it take to change a starter?
between 2 and 4 hoursDue to the complexity of starter motors, the average amount of time it takes to completely replace a starter is generally between 2 and 4 hours. If your car has an easily accessible starter and you take it to a mechanic worth their salt, your time should hopefully be closer to 2 hours rather than 4.
How do you test a starter solenoid?
To get started, locate your starter solenoid by following these simple steps:Open Your Vehicle's Hood. ... Find The Starter. ... Identify The Starter Solenoid. ... Observe A Clicking Sound While Someone Turns On The Ignition Switch. ... Test The Battery. ... Check For Current Resistance Using A Jumper Wire.More items...•
What would cause a Chevy truck not to start?
The most common reasons a Chevrolet Silverado 1500 won't start are a dead battery, an alternator problem, or failed starter.
What are the symptoms of a bad starter in a GMC Sierra?
These include a bad battery, battery cables, or a neutral safety switch issue. Starters are not expensive, but replacing them can be tricky. Bad Starter Symptoms: GMC Sierra. Noises coming from the starter and the vehicle itself not starting are the most common symptoms of a bad starter in your Sierra. 1.
Why won't my Sierra start?
Common other reasons your Sierra won’t start include: Bad Battery Cables or Terminals– Throughout your Sierra’s life, the battery cables and terminals can become corroded. This corrosion keeps the proper voltage from getting to the starter.
What to do if your Sierra battery is corroded?
If they are corroded, you’ll need a good wire brush or terminal cleaner to them cleaned up.
Why does my Sierra make a whirring sound?
If you hear a high pitched whirring sound, it may indicate that your Sierra’s starter is bad, or it could mean that the starter is turning, but not making contact with the flywheel. This is often caused by starter bolts that were not torqued tightly enough, or a broken flex plate/flywheel tooth. 2.
How to locate the starter on a 1993 gmc sierra 2 wheel drive 4.3
Its on the right (passenger) side of the engine, at approximately 7:00 o'clock, looking at it. It is located below the exhaust manifold. It may be better to look thru the right side wheel well to see it.
How do I change the starter on my GMC Sierra
give these websites a try www.alladity.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual it will have pictures and diagrams as well wish you the best of luck Michigan Man.
Where is the starter on a 2002 GMC Sierra 1500 HD located?
If you are taking about the starter moter, it is located on the passenger side of the block look from under side starts where the transmission meets the motor . Two big bolts heads and a round cylinder.
Changing the Starter
The starter is located on the passenger side rear of the engine Two bolts (size13mm??) Be sure to disconnect the pos. battery cable first, before disconecting the wires from the starter,otherwise, you'll ground those wires out and have fireworks.
What does it mean when the starter on a GMC Sierra stops working?
The solenoid then forces the gear in the starter housing to engage the engine. When the starter motor turns on and spins the gear, the engine roars to life. If any of these stop working, it means the starter won't turn over in your GMC Sierra.
Where is the solenoid on a starter motor?
The solenoid bolts to the side of the starter motor. Locate the two wire connectors on the back of the solenoid. The wire on the left connector connects to the ignition switch. The wire on the right connector connects to the starter motor.
Why won't my Sierra start?
Because the solenoid is shorted out and will not kick the starter gear into the engine, the Sierra will not start. However, the starter motor should turn on. If the starter motor does turn on and makes a humming sound, the starter solenoid is defective.
Where is the starter located on a V8?
The starter is located underneath the engine on the front passenger's side. On V8 engines, there is a bell cover housing that must first be removed to access the starter. Once this housing is removed, use a 13mm socket with ratchet and extension to remove the two bolts holding the starter in place.
How to jack up a truck starter?
For this DIY job, jacking up your truck is optional because the starter can still be accessed without raising the vehicle. Place a floor jack under the center of the front crossmember. Lift the truck and place jack stands underneath the side rails to support it.
Does a starter last longer than a battery?
The starter generally lasts longer than the battery, but when it does eventually fail, you'll be stuck wishing it had enough juice to bring your truck back to life one more time. Replacing the starter in your Silverado isn't a difficult job, and can be completed with just a few basic tools as well as a bit of your time.
