Enter the iAquaLink device number found on the door hanger or the device itself. Click to see full answer. Also question is, what is AquaLink? iAquaLink allows you to control your pool anytime, anywhere.
What part number do I use for Aqualink touch™?
If you have Aqualink Touch™. use Part Number IQ900. Aqualink All-Button Panel Aqualink OneTouch™ Panel
How do I set up my Aqualink device?
1. Setup • Upgrade models available for virtually any AquaLink ever made! • Easy installation with a single device that attaches to any AquaLink RS or PDA Power Center. • Can be installed indoor or out, using Wi-Fi or ethernet cable. 2. Configure • Connects to customer’s internet.
What is Aqualink system?
AquaLink system is an expandable monitoring platform that enables the public utility companies to gain control over their water network in a simple and effective manner. The system is composed by battery powered field devices that are installed on the existing water district meter and a cloud based software that enables mobile online monitoring.
How do I know if my iaqualink is connected to WiFi?
Within 2 minutes, the yellow LED should stop blinking on the iAquaLink. When the green LED illuminates, the iAquaLink is connected. WiFi setup requires connecting via hotspot on your cell phone.
How do I connect my iAquaLink to my phone?
0:495:06How to set up I-Aqualink for your pool - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf your antenna was previously connected you're going to have to remove the screws out of the frontMoreIf your antenna was previously connected you're going to have to remove the screws out of the front of the box. Take the cover off please note that the rubber gasket stays on and you'll see a switch
Can't connect to AquaLink?
If the process fails, the iAquaLink device will need to have its memory cleared by physically toggling the WiFi-Wired switch to Wired then back to WiFi. This will restart setup mode so you may attempt to connect it to your eero network again.
How do I connect my AquaLink RS to WiFi?
3:006:47iAquaLink 2.0 installation video - YouTubeYouTubeStart of suggested clipEnd of suggested clipAfter clearing the Wi-Fi settings. And with the switch in the Wi-Fi. Position press and release theMoreAfter clearing the Wi-Fi settings. And with the switch in the Wi-Fi. Position press and release the WPS. Button and wait for the small yellow LED next to the WPS button to begin blinking.
How do I reset my iAquaLink 2.0 WiFi?
0:182:54Get iAqualink back online - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo what I'll actually do probably is just reset my Wi-Fi. Turn it off turn it on and then it shouldMoreSo what I'll actually do probably is just reset my Wi-Fi. Turn it off turn it on and then it should actually.
How do I reset my Jandy AquaLink?
How do I Reset a Jandy AquaLink System?Press the "Menu" button.Scroll to and highlight "System Setup" using the arrow keys. Press "Enter."Scroll to highlight "Clear Memory," then press "Enter." You have now reset your AquaLink system. references. South Shore Gunite Pools: AquaLink Control Systems. you may like.
How do I reset my iAquaLink password?
Note that if you have an invalid or non-working email address, you will not be able to reset your password and will need to call our Customer Experience team at (800) 822-7933 to reset your account.
How do I fix iAquaLink waiting for connection?
0:452:09How To Fix "Waiting For Connection" For Jandy iAqualink AutomationYouTubeStart of suggested clipEnd of suggested clipLet us sit there for a second good five seconds or so and then go ahead and plug it back in and thenMoreLet us sit there for a second good five seconds or so and then go ahead and plug it back in and then from there you should be able to have. Your phone connects to your automation.
How do I use Aqualink?
1:362:39Aqualink RS by Zodiac, walk thru and demo - YouTubeYouTubeStart of suggested clipEnd of suggested clipI just put a push of the button inside your house or with a remote. And it's a very convenient wayMoreI just put a push of the button inside your house or with a remote. And it's a very convenient way to operate your pool.
How do I send iAquaLink invitation code?
1:116:18iAqualink 2.0 Mobile Device Setup and Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd then your password. Is. Right there and then type in a postal code it's gonna make one up real.MoreAnd then your password. Is. Right there and then type in a postal code it's gonna make one up real.
How do I program my Jandy Aqualink RS?
Basic Programming: To set a particular piece of equipment to turn on and off at a predetermined time, press the MENU button, press the forward arrow button to scroll to the PROGRAM menu, press ENTER, and then press the button for the equipment that you want to program.
What is eero router?
Unlike the familiar router-to-range extender network configuration, eero is a WiFi system that uses multiple access points to provide your home with fast, reliable coverage all on a single network. Range extenders can expand the reach of your existing wireless network.
What is AquaLink system?
AquaLink system is an expandable monitoring platform that enables the public utility companies to gain control over their water network in a simple and effective manner.
Why is AquaLink important?
"AquaLink is ideal, because it allows insight into the system in places where the use of our Scada system is not possible. It is also useful as a support system to the existing system and for detecting water defects."
How long does it take for the yellow LED to stop blinking on an iAquaLink?
Within 2 minutes, the yellow LED should stop blinking on the iAquaLink. When the green LED illuminates, the iAquaLink is connected. WiFi Setup (iAquaLink 2.0 and greater): WiFi setup requires connecting via hotspot on your cell phone.
What is iAquaLink?
iAquaLink is a remote pool control system that allows you to control temperature, pumps, filters, lights etc for your pool and spa systems.
What happens if iAquaLink fails?
If the process fails, the iAquaLink device will need to have its memory cleared by physically toggling the WiFi-Wired switch to Wired then back to WiFi. This will restart setup mode so you may attempt to connect it to your eero network again.
What does it mean when the iAquaLink LED turns green?
If the iAquaLink LED turns green, it’s successfully connected to the WiFi. After clearing the WiFi settings, by physically toggling the WiFi-Wired switch to Wired then back to Wi-Fi, use a smartphone or WiFi enabled device to go to WiFi settings and connect to the network labeled "iAquaLink".
