Receiving Helpdesk

what nails do i use for cedar shingles

by Dayne McKenzie Published 3 years ago Updated 3 years ago

Which Types of Nails Are Best for Cedar Shingles?

  • Correct Nails for Cedar Shingles. The ideal nail types for cedar shingle roofing projects include corrosion-resistant varieties like stainless steel and hot-dipped galvanized.
  • Nail Sizes for Cedar Shingle Roofing. The size of the nail to use depends on the roofing thickness. ...
  • Contact Cedar Roof Coatings for Cedar Roof Repair and Maintenance. ...

Correct Nails for Cedar Shingles
The ideal nail types for cedar shingle roofing projects include corrosion-resistant varieties like stainless steel and hot-dipped galvanized. At Cedar Roof Coatings, we advise against the use of plain steel nails to keep the cedar roofing stain-free over time.
Mar 10, 2020

Full Answer

What size nail should you use to install shingles?

Which Types of Nails Are Best for Cedar Shingles?

  • Correct Nails for Cedar Shingles. The ideal nail types for cedar shingle roofing projects include corrosion-resistant varieties like stainless steel and hot-dipped galvanized.
  • Nail Sizes for Cedar Shingle Roofing. The size of the nail to use depends on the roofing thickness. ...
  • Contact Cedar Roof Coatings for Cedar Roof Repair and Maintenance. ...

What is the best nail for cedar siding?

  • Specs: Fastener Length Capacity: 15-degree, 13-14 ga plastic/wire-collated siding nails, 1-1/4” to 2-1/2”. Magazine Capacity: 200-400 pcs.
  • Pros. Economical option. Plenty of storage options. ...
  • Cons. Good capacity air compressor needed. If you’re looking for a reliable staple gun for shingles, we propose this wonderful staple gun from Senco.

What is the best nail for cedar shakes?

“ The CSSB favors the use of aluminum/stainless steel nails for cedar shingles. However, if you’d rather use staples, go for stainless steel staples Type 316 in sites within 15 (fifteen) miles of salty water. Use Type 304/Type 316 for locations further from the defined salt water zone ”.

How to use nails or staples on cedar fencing?

Key specifications

  • Staples: 5ga, 7/8” to 1-9/16” barbed fencing staples (glue collated)
  • Magazine capacity: 50 pcs
  • Overall weight: 97 pounds
  • Operating pressure: 70 – 115 psi

Can you use a nail gun on cedar shingles?

Tools & Fasteners It's possible to install cedar shingles with a hammer, and that provides the most control, but with 900 nails per square, the job will go a lot faster if you use a pneumatic nail gun. The other big advantage to using a nail gun is that you have one hand free to hold the shingle-strip.

What nails do you use with cedar?

Hot-dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and can be used to nail Western Red Cedar. Other types of nails are not recommended. They can rust and disintegrate and react adversely with the natural preservative oils present in cedar resulting in stains and streaks.

How do you nail cedar shingles?

2:167:01How to Install Cedar Shingle Siding | This Old House - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's a ring shank stainless steel nail. You really only need two nails per shingle. And you want toMoreIt's a ring shank stainless steel nail. You really only need two nails per shingle. And you want to be in about three quarters to one inch on each edge.

Can I use galvanized nails for cedar shingles?

A galvanized nail is also not a good choice as they contain zinc which reacts chemically with both cedar and redwood. Galvanized-coated steel nails should also not be used during a cedar shake or shingle installation.

Do you need special nails for cedar?

Hot-Dipped galvanized, aluminum and stainless steel nails are all corrosion-resistant and all can be used to nail Western Red Cedar. Other types of nails are not recommended. They can rust and disintegrate and react adversely with the natural preservative oils present in cedar resulting in stains and streaks.

What fasteners to use with cedar?

Cedar,” of the Western Red Cedar Lumber Association (WRCLA). The best option is stainless steel, which is the least likely to react with water and salt. At bare minimum, fasteners should be hot-dipped galvanized, in which the nail or screw is coated with zinc to protect it from corrosion, meeting ASTM A153.

What do I put under cedar shingles?

Synthetic underlayment: With modern improvements and manufacturing techniques, synthetic underlayments are now considered the best material installed under cedar shingles. Synthetic underlayments are made from polyester, fiberglass and polypropylene.

How much do you overlap cedar shingles?

from each edge of the cedar shingle and 4 cm (1 1/2 in.) above the exposure. To avoid buckling, allow 3 to 6 mm (1/8 to 1/4 in.) space between each shingle for expansion (depending on degree of humidity).

How do you install a cedar shingle roof?

2:029:54Wood Shake Roof | Installation Guide - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow like with any other roofing project you want to make sure that you have a solid roof deck now onMoreNow like with any other roofing project you want to make sure that you have a solid roof deck now on this project we're not going to talk a lot about about root decking just because there are other

Why can't I use galvanized nails in cedar?

However, the zinc in galvanized nails reacts chemically with cedar and redwood. Nail manufacturers recommend that you go with aluminum or stainless steel fasteners when you're using either of these woods—and whenever you're using pressure-treated wood. (The preservatives incorporate salts that react with the zinc.)

What is a #8 nail?

For historical reasons, nails are sold both by a number followed by d and (less confusingly) by length. The “d” stands for penny, so 8d refers to an 8-penny nail, 16d to a 16-penny nail and so on.

What type of nails should I use for cedar siding?

Ideal nails to use on cedar wood are made from aluminum, double-dipped galvanized, or stainless steel. Other types of nails such as plain steel nails are not advisable because reactions between the nails and the siding and the environment will create ugly stains on your siding over time.

How many nails should I use for a shingle?

Use rust-resistant shingle nails or staples 1-1/4" to 1-1/2" (3.2 to 3.8 cm) long, galvanized, in aluminum or stainless steel. Use 2 nails per shingle at about 3/4" (1.9 cm) from each edge, and 1" (2.5 cm) above the butt line of the overlapping shingle. Click to see full answer.

Which Types Of Nails Are Best For Cedar Shingles

It’s essential to consider the size and type of nails when installing cedar shingles. The right fasteners can ensure longer-lasting cedar shingles or shakes. The distance the nails are driven also makes a difference, as forcing them too deep could cause splitting in the wood.

How Are Cedar Shakes Installed

Homeowners usually install cedar shakes either all at once, or in layers to make some sort of pattern. To encourage a longer life, the wood must be treated prior to installation, and checked and replaced when necessary. This is most often done at the factory for the benefit of customers who are interested in a rustic look meant to last.

Type Size And Spacing

For best results use splitless siding nails. These have thin shanks and blunt points to reduce splitting. For greater holding power, nails with ring threaded or spiral threaded shanks are recommended. Nails with textured heads can be used to reduce glossy spots at the nails when finishing .

What Nails Are Best

The type of nails you choose to use when installing cedar shake siding should be considered also. The right nails play an important role in ensuring that your cedar wood siding endures for a long time. Ideal nails to use on cedar wood are made from aluminum, double-dipped galvanized, or stainless steel.

When To Use A Framing Nailer For Fencing

A framing gun carries the day for fencing work if youre fastening boards or wood planks to wooden posts.

What Kind Of Nails Do You Use On Cedar Siding

For siding up to 6 inches wide, use one nail one inch up from the lap. Face nail with two nails per piece for 8 inches patterns and wider, keeping nails 2 ½ to 3 inches apart to allow for dimensional movement without splitting. For vertical applications, siding should be nailed to horizontal blocking or furring strips.

Benefits Of Cedar Shake Siding

Cedar shake siding has been a firm fixture in construction history, and has experienced waves of popularity throughout the years. Cedar shake siding is a great addition to your home because it provides an extra level of protection against the elements as well as natural insulating qualities.

What type of nails should I use for wood siding?

Similarly, what nails should I use for wood siding? Hot-dipped galvanized nails are suitable, but stainless steel or high-tensile aluminum ones are better. The nails should have ring or spiral shanks; smooth-shank nails tend to pop out.

Can you use a framing nailer for siding?

The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing. While it's recommended to always use a siding nail gun for siding installation, in a pin ch, you may be able to use a framing nailer instead.

What type of nails are used for a ceramic roof?

Stainless steel nails are best used for slate and ceramic roofs or asphalt shingle roofs in coastal climates. For asphalt roofing shingles, use galvanized nails. Galvanization adds a layer of zinc onto the steel that significantly inhibits rust and corrosion.

What are the different types of roofing nails?

Three Basic Types of Roofing Nails. There are three basic types of roofing nails: 1. Smooth Shank. The shank of the nail is the part of the nail that punctures through the material you are nailing. Simply put, smooth shank nails have a smooth shank.

What is a ring shank nail?

Ring Shank. A ring shank nail is also called an annular roofing nail or corrugated roofing nail. As its many names suggest, this type of nail has rings along the shank. They aren’t connected, as they are with screws. Still, these rings give the nail extra staying power, or grip, in the shingles and sheathing.

How long should a roof nail be?

Length of Roofing Nails. Roofing nails are available in lengths ranging from one to two inches. Roofers seek to use just the right length of nail so that the decking (or OSB) is completely punctured by the nail. The puncture must be complete so that the whole diamond tip is past the wood.

What is a diamond shaped nail?

Roofing nails are cleverly designed to help you do a better job. Though they vary greatly in material, size and type, all roofing nails share one helpful characteristic: a diamond‐shaped point. This point is expertly designed to keep the decking intact when it punctures through.

What type of nails are used for felt underlayment?

So, choose these nails where performance, especially wind resistance, is a priority. 3. Square Cap. Square cap nails are typically used for fastening felt underlayment and not asphalt shingles. They have a square-shaped head, instead of the more typical circular head you see on other nails.

What gauge is a roof nail?

Roof nails are available in 12-, 11- and 10-gauge. The lower the gauge number, the thicker the nail. Under most building codes in North America, 12-gauge is the minimum thickness of nail allowed on a roof. Roofing nails that are 11- or 10-gauge are also allowed by most building codes as they are thicker and sturdier.

Can you use a nail gun on cedar shingles?

Other than that, it’s a nail gun for cedar shingles you’ll be happy with for years to come particularly if you only have occasional cedar shingles tasks .

Do nails work on cedar siding?

As you have noted, for the most part, nails work better than staples for cedar shingles so it’s best to invest in one of the two siding nailers (or rent depending on how frequently you’ll be tackling cedar shingles installation projects).

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9