What are the Differences Between Eaves and Rake Edges?
- The eaves of a roof are the part of the roof that overhangs the outside walls of the home at the bottom part of the roof. ...
- The rake edge of a roof is the slanting edge on the end wall of the house. ...
- The fascia is the decorative board that extends down from the roof edge. ...
- Felt paper is made of a combination of asphalt and either paper or rags. ...
How to build your own roof rake?
- orientation of the roof to the sun’s path
- optimum solar panel pitch
- typical live loads our roof would experience based on seasonal weather (snow and wind)
- typical annual rainfall for the area
What to look for in a roof?
- Walk the roof to feel for spongy or flexing areas that indicate rotted or broken roof decking
- Look for areas where roofing nails are pulling out, an indication the wood beneath is soft and won’t hold the nails securely
- Examine the underside of the roof deck from inside an attic, where possible, to look for damage or staining caused by leaks
What is meant by "the rake of the roof"?
Rake on the roof is the exposed outer portion of a roof to a roof extending from the infinity to the ridge . The drip edge is also installed along with the rake. There are three types of roof rakes: hanging exposed, overhanging and boxed, and abbreviated or extended. The exposed rakes are often in sheds or lodges.
How to install a roof edge?
- Starting at the bottom of the roof, map out a guideline with chalk.
- Starter shingles are available and are a must to achieve maximum wind warranties.
- Place the glue strip along the eave and rake edge and drip edge.
- Nail your shingle into place.
What's the difference between rake edge and drip edge?
So, the drip edge attracts the rain droplets, snow, all types of precipitation into the eavestroughs, and away from the rest of the roof. Rake edges, on the other hand, are placed along the ends of the gables of a house's roof.
What does the term rake mean in roofing?
Rake. The slanting edge of a gable roof at the end wall of the house.
Is rake drip edge necessary?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
What is the difference between gable and rake?
Gable: The A-shaped side wall of the home that forms the peak of the roof is called the Gable. The home above has two gables, one on each end of the home. Rake: The rake of the roof is the part that ends over a gable end.
Is roof raking necessary?
If your roof is flat or has a low slope, roof raking is definitely a must once the snow gets to be about 6 inches or more. If your roof has a higher pitch, it's still something to consider, especially if the snow is wet and heavy and it is building up.
What is rake trim?
Also known as rake trim, gable trim is a finishing piece of metal flashing used along the edges of a metal roof line where the edge of the metal roof panel meets the endwall panels.
Do you put drip edge on rake edge?
A drip edge should be installed on the eaves and rakes of the roof, flush with the decking and fascia. On eaves, the drip edge is installed directly to the deck with underlayment installed over it for proper water shedding. On rakes, the underlayment is installed over the drip edge.
How far should shingles hang over rake edge?
The edge of the shingles should hang over a roof between an inch and an inch and a half — or between a half inch and three-quarters of an inch if drip edge flashing is installed. Too much overhang and the shingles could blow off in high winds; too little can allow water to seep into rake or fascia boards.
What is the difference between rake and gable trim?
Rake trim (also known as gable trim) is a metal flashing finishing piece placed along the roofline at the sloped sides at the end of a residence's dormer or gable. Rake trim can be flat with no overhang, or it can overhang the gable end like an eave.
What is the edge of a roof called?
EavesEaves. The lower edge of a roof (usually overhanging beyond the edge of the house).
What is rake overhang?
The American Wood Council's 2012 Wood Frame Construction Manual defines rake overhang as “The horizontal projection of the roof measured from the outside face of the gable endwall to the outside edge of the roof.” Section 2.1. 3.4.
What is the trim around a roof called?
FasciaFascia: Vertical roof trim located along the perimeter of a building, usually below the roof level, to cover the rafter tails at the eaves and to seal off the top of the siding along the rake; also called gutter boards.
What is a rake on a roof?
The rake is not exactly on the roof. It is a term that describes the sloped sides of a gable end. The rake can be flat with no overhang, or it can overhang the gable end like an eave.
What are the different types of roof rakes?
Types of Roof Rakes. There are three types of roof rakes: overhanging exposed, overhanging and boxed in, and abbreviated or extended. Exposed rakes often are on sheds or cottage homes. The rafters and framing in the eaves are left open. A closed rake is boxed in.
How wide is a rake board?
Roof rake boards are installed in different widths based on the surface being covered. One-by-2-inch rake boards often cover the exposed top edge of the siding when there also is an eave overhang on the gable end. Use larger rake boards such as 1-by-4-inch and 1-by-6-inch when there isn't an eave overhang on the gable end.
What type of rake board do builders use?
The type of rake board a builder uses is based on the style of trim and fascia on the rest of the house or building. Rake boards may be wrapped in metal to match metal-wrapped fascia or painted to match painted trim. Advertisement.
What is the top edge of a rake board?
The top edge of the board rests against the roof decking and the bottom edge covers the siding or brick. The length of a rake board varies depending on the length of each side of the gable. Advertisement. references & resources.
Where is the rake board on a brick house?
Rake boards are installed on the gable ends of brick houses to cover the exposed top edge of the brick.
Does Hunker roof rake always angle down?
Hunker may earn compensation through affiliate links in this story. A roof rake always angles down. Roofing terminology may be difficult to understand unless you are a builder or roofer. Terms are used to break down the various areas of a roof and a "rake" is one of many roof sections. The rake is not exactly on the roof.
Defining the Rake of a Roof
The rake of a roof or a roof rake — not to be confused with the tool also called a roof rake — is a part of any gabled roof. Specifically, it’s the exposed part of a gabled roof that extends from an eave to the ridge of the roof’s sloped sides. It covers the top edge of a roof and is typically cut from a variety of roofing materials.
Different Types of Roof Rakes
Roof rakes can sometimes be exposed, such as often seen on cottages or sheds, where the eave’s framing and rafters are left open by design. More common is a closed rake, boxed in by the rake boarding and the soffit (its bottom surface), which is typically about six inches wide and simple in design.
Possible Problems with the Rake of a Roof
The reason it’s a good idea to be familiar with this term is that the rake of a roof can be vulnerable to specific problems that can become expensive inconveniences or even outright compromise the integrity of the roof.
Contact the Experts at Thompson Creek Windows Today
Rely on the experts at Thompson Creek for the highest standards in roof installation and replacements. With over 40 years of experience in providing dependable solutions using the highest quality materials, we’re always happy to help you find the best roofing for your home. Contact us today for a free consultation.
What are the different types of roof rakes?
Type. There are three types typically available for roof rakes, which are extended or abbreviated, overhanging and boxed in, and overhanging exposes. Cottages homes or sheds are usually used exposed rakes instead of closed rakes. The overhanging exposes and extended types are usually wider than the boxed-in types with more intricate details.
What is a rake made of?
The rake is often designed in such an intricate way. The size and materials vary, but it is commonly made from wood materials. It depends on the builders, as they often have different fascia or trim styles to match with the rest of the buildings. Some homeowners may choose to wrap the rake boards with metal to achieve a more polished look.
What are some roofing terms?
You may find several terms related to the roofing topics are decking, drip edge, eave, underlayment, and so many more. Rake is one of the roof sections that you may have heard of before.
Why wrap rake boards with metal?
Some homeowners may choose to wrap the rake boards with metal to achieve a more polished look. See Also : How to Install Drip Edge on Shed Roof. What is a rake on a roof purpose? The purpose of installing a rake board is to prevent roof damage from running or leaking water behind the siding.
How big is a rake board?
The exposed top edge is usually covered by one 2-inch sized rake board. The larger sizes are available in one 4-inch or one 6-inch. The length of the rake differs according to the length of the gable’s sides.
Is a rake on a roof?
In fact, the rake is a term used to refer to the sloped sides at the end of the gable, so it is not exactly on the roof. The rake may overhang at the tip of the gable or not overhang and lying flat. It is either left open or closed with fascia or soffit.
Why use a rake edge on a roof?
Both of these edges may be used in a climate that is tropical because of the nature of heavy rains.
What is the angle of a rake edge?
The metal of a rake edge, on the other hand, is bent at a 90-degree angle. It is bent that way so that it can lie properly on top of the gable of the roof. Different constructors, however, may apply different designs to their rake edges.
Why are rake edges called drip edges?
There are many cases where rake edges are also called drip edges because both of these types of edges essentially play the role of attracting precipitation away from the roof and into the gutters and troughs on the edges of the roof. Edges perform this function in order to prevent the prolonged exposure of the roof to this precipitation, ...
What is a drip edge?
The edge plays the role of redirecting water droplets from the wooden portions of the roof and protecting the underpinnings of the roofing system. Drip edges and rake edges are both metal sheets that are installed as part of the roofing system, and, as the “edge” in their name implies, they are placed at the edges of the roof.
What material is used to make drip edges?
Both drip edges and rake edges can be formed with aluminum, galvanized steel, or copper. Aluminum is most common as it does not corrode, is lightweight yet durable, and can be sold in several different colors.
How many sides does a gable roof have?
A gable style roof has two sloping sides and a gable at each end. You can picture the gable visually as being that portion of the triangular portion of the roof where the roofing comes up just a little from the rest of the roof and juts out, emphasizing the triangle.
Where do rake edges come together?
The rake edges of the roof along the gables will be installed from the bottom edges of the roof to the top of the ridge, where they will come together to form a triangular shape. This will be clearly visible to passersby, unlike the drip edges.
