What does f9 mean on a Whirlpool range? F8 - Control Board Failure - Replace control board (clock). F9 - Oven Door Lock Failure - Check door lock switches and wiring. Check for stuck lock switch.
How do I fix error code F9?
Reset the Oven Sometimes, the F9 error code is the result of an electrical fault that has magnetized the circuitry. Resetting the oven by disconnecting the power for five minutes will demagnetize the circuitry and resolve the F9 error.07-Jul-2021
How do I fix the F9 on my Whirlpool oven?
Reset the appliancePower unit down by turning off the circuit breaker(s) for one (1) minute.Monitor the range or oven for one (1) minute to ensure the error code does not display again.Verify the range or oven operation.
How do you clear the error code on a Whirlpool oven?
Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E0 persists then replace the electronic oven control.06-Sept-2016
How do I clear F9 code?
How to Remove the F9 Code From MaytagHold on the "Start/Stop" button for 10 seconds. This will end the beeping. ... Open the oven door and check the door latch. ... Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. ... Press the oven door shut gently. ... Test the oven.
How do I clear E1 F9 code?
Follow the checks below to resolve error code E1/F9.Try a Reset. Sometimes an error code is caused by a control board glitch, where resetting the washer is all it takes to resolve the error code. ... Check your Detergent. ... Check the Drain Hose. ... Clean the Filter. ... Check the Drain Pump. ... Check the Wiring.01-Nov-2021
Why does my oven say F9?
An F9 error code on a General Electric (GE) oven indicates that the oven's electronic control system has detected a problem with the automatic door lock. ... The malfunction may be a jammed door lock mechanism, a pinched or broken wire, a faulty lock switch or a fault in the control board itself.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load WasherError CodeErrorSud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,F8 E1 or LO FLThe washer is sensing a low flow of water.7 more rows•15-Jun-2020
Does a Whirlpool oven have a reset button?
This is a soft reset and will simply get you out of any program you have started. Press it when the cooking complete reminder appears on the display, for example, and the "Your Food is Ready" message will disappear. Press the "Off/Clear' button for three seconds to turn the "Control Locked" child lock off.27-Aug-2017
How do I run a diagnostic on my Whirlpool oven?
Enter Diagnostics mode by pressing CANCEL>CANCEL>START within a 5-second period. Entering Diagnostics mode will cancel any active oven operation. Enter the Diagnostics mode only after the oven is cool. All elements (depending on which cycle is being used) will operate with the oven door open.
Why is my Whirlpool oven door locked?
Why would you find your Whirlpool oven door locked? It's often because the control panel lock was set inadvertently. Holding down the START button for 3 seconds should clear the setting and unlock the door.01-Dec-2020
How do you reset the oven door latch?
1:088:34Oven Door Won't Unlock - Troubleshooting | Repair & ReplaceYouTubeStart of suggested clipEnd of suggested clipBefore you try anything else it's best to reset the oven disconnect the power at the breaker. WaitMoreBefore you try anything else it's best to reset the oven disconnect the power at the breaker. Wait five minutes and turn the breaker back on.
How do I unlock my oven door?
To unlock an oven, hold down the Lock button on your control panel for 2 or 3 seconds and wait for the oven to beep to indicate it's unlocked. If this doesn't work, unplug it from the electrical outlet and wait a few minutes. Then, plug it back in again, which may reset the temperature gauge and cause it to unlock.
How do you fix error F9 on LG oven?
Try to reset the unit by either unplugging the range or switching circuit breaker to “off” position. 5. Advise customer to leave it “as is” for 3 to 5 minutes then re-plug or switch breaker back “on”.
How do you clear a Whirlpool oven code?
Plug the oven power cord back in or turn ON circuit breaker. Press CANCEL on the display. If fault code comes back after 1 minute then replace the keypad. If F2 E0 persists then replace the electronic oven control.
What is a F9 code on a LG oven?
If the Control Panel Display lights up error code “F-9” it means oven failed at exceeding 150ºF after 5 minutes of preheating. 3. Have customer press the Clear/Off button to terminate the beeping alarm. 4. Try to reset the unit by either unplugging the range or switching circuit breaker to “off” position.
Why does my Whirlpool oven say Loc?
LOC error normally means that it is child locked. You have to press and hold one of the buttons for ten seconds depending on the model. Start by trying the ‘Start’ or ‘Cancel’ button.
What does F9 mean on LG oven?
If the Control Panel Display lights up error code “F-9” it means oven failed at exceeding 150ºF after 5 minutes of preheating. 3. Have customer press the Clear/Off button to terminate the beeping alarm. 4. Try to reset the unit by either unplugging the range or switching circuit breaker to “off” position.
