Videos of Toilet Flange Repair Kit With Concrete Floorbing.com/videos
Images of Toilet Flange Repair Kit With Concrete Floorbing.com/images
How do you replace a toilet flange in concrete?
InstructionsCut off the Old Flange and Obstructions. After you remove the toilet, you will probably find an existing toilet flange. ... Scrape off Old Wax Ring. ... Pick the Correct New Toilet Flange. ... Place T-Bolts in New Toilet Flange. ... Position Toilet Flange. ... Drill Holes Into Concrete. ... Screw Toilet Flange Onto Concrete.Oct 31, 2021
How do you anchor a toilet flange to a concrete floor?
3:024:21Toilet Flange Installation on New Construction - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd driving them with a nut driver. Bit. Continue around the flange drilling holes and securing intoMoreAnd driving them with a nut driver. Bit. Continue around the flange drilling holes and securing into place with the concrete anchors. Once the flange is secured. The floor can be tiled and the toilet.
How do you fix a wobbly toilet on a concrete floor?
1:013:46How to Fix a Toilet - Cement Sub-Flooring Repairs - Part 1 of 2YouTubeStart of suggested clipEnd of suggested clipThere are two ways this problem can be corrected. The first way is by installing a replacement ringMoreThere are two ways this problem can be corrected. The first way is by installing a replacement ring over the top of the existing flange.
Do you have to screw a toilet flange on concrete floor?
Yes, you have to screw or bolt the toilet flange to the floor. If you do not, you risk not securing the toilet enough to prevent rocking that may damage the wax seal, the drainage pipe, or the floor.
How far can a toilet flange be above the floor?
1/4 inchThe optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal. If you recently tiled or changed the bathroom flooring, the flange height is likely less than optimal.Jan 2, 2022
How do you install a toilet flange bolt?
1:192:52Kitchen & Bathroom Repairs : How to Install Hold-Down Bolts on a ToiletYouTubeStart of suggested clipEnd of suggested clipGo ahead and slide them back into. Place. Then what you're going to do is go ahead and take the waxMoreGo ahead and slide them back into. Place. Then what you're going to do is go ahead and take the wax ring that you got put it back on the toilet. And then we're going to ease it into place.
Does toilet flange go inside or outside pipe?
Install a toilet flange on the outside. This can be done with a hammer and chisel. If the flange is cast iron with a rubber gasket, you should be able to remove the cast iron with a hammer and chisel, remove the rubber gasket with a sharp knife, then replace the gasket and the flange.
What do you do if your toilet flange is too high?
0:0714:19Fix toilet flange that is TOO HIGH - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd bolting it down we did a dry run we always recommend doing a dry run when you are replacing aMoreAnd bolting it down we did a dry run we always recommend doing a dry run when you are replacing a toilet.
How do you fix a loose toilet flange?
0:171:37ROCKING OR LEAKING TOILET FLANGE REPAIR (CC) - YouTubeYouTubeStart of suggested clipEnd of suggested clipNew wax ring tighten the bolts down as solid as a rock it's ready to go. And you can do this on bothMoreNew wax ring tighten the bolts down as solid as a rock it's ready to go. And you can do this on both sides if you need to oh yeah.
Does toilet flange need to be secured to floor?
The flange should be fastened to the floor. Dry fit the toilet to make sure it doesn't rock. If it does rock, use shims to prevent rocking - just tightening the bolts probably will not stop the rocking but will risk cracking the toilet or breaking the flange.Jan 9, 2015
What happens if you remove a wax ring from a drain?
After you remove the obstructions, the old wax ring will still be in place around the drain opening. The wax most likely will be thick, sticky, and possibly stained with sewage. Removing the wax ring requires patience, a putty knife, and latex gloves.
What tool do I need to drill into masonry?
If you expect to drill into masonry more often, purchase a good-quality tool, such as a Bosch, Hilti, DeWalt, or Milwaukee hammer drill. Because the old bolts will need to be cut off, you'll need some type of power tool to do the job. A manual hacksaw will not work, because you need to move the saw blade against and parallel to the concrete slab.
Can you rotate a toilet flange?
You can rotate the flange in either direction until you have reached the preferred position. After the toilet is placed, you will still have the opportunity for some minor rotation, but it is still best to get the position as straight as possible before securing the flange. Lee Wallender.
Can you drill holes in concrete to replace flanges?
When the subfloor is concrete, as is often the case with basement bathrooms or other slab foundation situations, replacing the flange is no easy matter, since it can be quite hard to drill holes in concrete to secure the new flange. But using two specialty tools—a multi-tool or similar cutting device, along with a hammer drill—makes it fairly easy ...
Toilet Flange Overview
A toilet flange is a pipe fitting that connects a toilet to the home’s drainage system. It also mounts a toilet securely to the finished floor. There is a variety of toilet flanges to choose from on the market today, such as PVC, ABS, cast iron, copper and stainless steel, depending on your particular application needs.
Assessing the Problem
In addition to your toilet rocking, there are other warning signs that may indicate your flange is broken including:
Prepping Toilet for Repair
First, turn off the water supply to the toilet by turning the valve in a clockwise direction. The water supply valve should be located behind the toilet just to the left. If a valve is not present, you will need to find another valve located in the basement or crawl space area of the home.