Yes, Crystal Blue Copper Sulfate
Copper(II) sulfate
Copper(II) sulfate, also known as copper sulphate, are the inorganic compounds with the chemical formula CuSOₓ, where x can range from 0 to 5. The pentahydrate is the most common form. Older names for this compound include blue vitriol, bluestone, vitriol of copper, and Roman vitriol.
How do you use crystal blue copper sulfate granules?
For most applications of Crystal Blue Copper Sulfate, you will dissolve the granules in water and then spray over the water surface. Per the product label, you should not apply granules directly to the water unless you have the proper equipment and are already familiar with this treatment.
Is crystal blue copper sulfate safe for fish?
Crystal Blue Copper Sulfate controls most species of algae like filamentous or string algae with very low concentrations of copper sulfate. Crystal Blue Copper Sulfate is granular copper sulfate. Treatment of algae can result in oxygen loss from decomposition of dead algae. This loss can cause fish suffocation.
How do you apply copper sulfate to water?
Application by Spraying Solution on Water Surface: Dissolve the minimum required dose of Copper Sulfate in water and spray the solution uniformly over the body of water. When spraying a solution of copper sulfate, mix copper sulfate in sufficient water to thoroughly spray the water surface.
How to grow copper sulfate crystals?
To grow copper sulfate crystals, you’ll need: There are 2 types of copper sulfate crystals you can grow: single crystals and crystal clusters. The procedure to grow them is slightly different.
How to apply copper sulfate?
How far apart should you drag copper sulfate?
Which counties in California have copper sulfate?
Can copper sulfate kill pondweed?
Is copper sulfate good for metal?
How do you use crystal blue copper sulfate smart crystals?
Apply by casting copper crystals over floating algae mats, dissolve in water, and spray, or place crystals in porous bag and drag behind boat. Treat a portion of the pond at a time to prevent oxygen depletion.
How do you mix crystal blue copper sulfate?
Crystal, or granular, copper sulfate should typically be dosed at five pounds per acre. Say, for example, that you have a one acre pond. You would mix 5 pounds of granular copper sulfate with 3 gallons of hot water, then spray it over half of your pond, wait a few days, and spray the other half.
How much water do you mix with copper sulfate?
Liquid Copper Sulfate Some liquid forms can be applied directly to the water, but the University of Florida IFAS Extension recommends diluting it to avoid using too much of it in one place. Typically, use 1 gallon of liquid copper sulfate diluted in 10 gallons of water per one surface acre of your pond.
How do you mix copper sulfate crystals with water?
1:465:29Making Copper Sulfate - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt's not usable. But because copper sulfate is a copper salt it will easily dissolve in water. So toMoreIt's not usable. But because copper sulfate is a copper salt it will easily dissolve in water. So to make something you can use just take around 2 pounds of these crystals. And put them into an empty
How do you apply copper sulfate?
Apply at a rate of 3 to 6 pounds per acre foot of water (0.27 ppm to 0.54 ppm copper in the treated water). Apply as a uniform surface spray dissolved in at least 3 to 5 gallons of water using boat, plane or other pressurized spray device. Apply twice yearly or as needed.
How long does it take for copper sulfate to work?
The treatment will likely cause a sudden, algal die-off causing an oxygen depletion that could result and the dead algae decay and the fish will suffocate. Treating only one third of an area at over 48-72 hours will help avoid crashing your oxygen levels.
How long does it take copper sulfate to dissolve roots?
It can take as little as two or three days to clear out the line. However, if your system has a slower flow of water, it can take a bit longer (up to a week) to get rid of the roots. By contrast, copper sulfate takes up to four weeks to even start the process of root decay.
How do you mix copper sulfate in a sprayer?
Use a ratio of 1 gallon of water, 3 1/3 tablespoons of copper sulfate, and 10 tablespoons of hydrated lime for each gallon of spray mixed. Start flowing water into the spray tank.
How long does it take for copper sulfate to dissolve in water?
In hard or alkaline waters, copper sulfate tends to settle to the bottom within 24 hours after application. Chelated copper remains in solution longer, allowing for a longer contact time with the algae.
What happens when you add water to copper sulfate?
If copper sulphate crystals are added to water then, the particles of copper sulphate crystals loses attraction between them and starts moving continuously and gets mixed up with water. It is called 'hydrated copper sulphate solution which is having a blue colour. Was this answer helpful?
Will copper sulfate damage pipes?
Under NO circumstances should copper sulfate crystals be placed in sink or tub traps where they will erode the light-weight metal pipes and cause leaks. It would be wise to leave the house for the day after treatment.
Is it safe to swim in a pond treated with copper sulfate?
When organisms such as algae become a problem in private or commercial fish ponds, copper sulfate treatment provides an inexpensive solution. However, improper application of copper sulfate can create more problems than it solves.
How to apply crystal blue copper sulfate to algae?
What is the best way to apply Crystal Blue Copper Sulfate on algae? A. Crystal Blue Copper Sulfate should be applied on a sunny day after mixed with water. You should spray one-half of the water area and wait 14 days before treating the remaining half. This will prevent the suffocation of the fish.
What temperature does crystal blue copper sulfate need to be?
Per the product label, "Generally, larger quantities of Crystal Blue Copper Sulfate will also be required to control algae growth when water temperatures are low (below 60ºF), in hard water, and in water that is free flowing".
Can crystal blue copper sulfate kill lichen?
Is the Crystal Blue Copper Sulfate formulation safe to kill lichen/algae growing on a live oak tree? If safe, how to formulate mixture for backpack sprayer. Yes, Crystal Blue Copper Sulfate can be used to kill lichen/algae on oak trees.
Can you use crystal blue copper sulfate on floor drains?
Crystal Blue Copper Sulfate cannot be applied directly into a floor drain as it will corrode metal drains. It also needs some water flow to work correctly and must be used before complete stoppage so it can get to the area of root growth. Please refer to the product label for the correct uses for this product.
Can you use copper sulfate on oak trees?
Yes, Crystal Blue Copper Sulfate can be used to kill lichen/algae on oak trees. You would use it at a rate of 8 oz. per 3 gallons of water per the product manufacturer. They also recommend mixing in warm water so the product can disolve the best.
What is crystal blue copper sulfate?
Crystal Blue Copper Sulfate controls most species of algae like filamentous or string algae with very low concentrations of copper sulfate. Crystal Blue Copper Sulfate is granular copper sulfate.
How long to wait to spray a fish with copper sulfate?
A. Crystal Blue Copper Sulfate should be applied on a sunny day after mixed with water. You should spray one-half of the water area and wait 14 days before treating the remaining half. This will prevent the suffocation of the fish.
Can you use copper sulfate on oak trees?
Yes, Crystal Blue Copper Sulfate can be used to kill lichen/algae on oak trees. You would use it at a rate of 8 oz. per 3 gallons of water per the product manufacturer. They also recommend mixing in warm water so the product can disolve the best.
Special offers and product promotions
Create your FREE Amazon Business account to save up to 10% with Business-only prices and free shipping. Register today
Product Description
Crystal Blue Copper Sulfate is a great pond algae control product for filamentous or string algae. Copper sulfate should be used as a pond algae treatment on actively growing algae in water temperature above 60F.
Copper Sulfate for Algae Control in Ponds
Although copper sulfate has many uses, it is widely known as an effective and economical chemical to kill and control algal growth in ponds. It can get rid of both filamentous and planktonic algae (the two most common aquatic plant problems) before it rapidly reproduces and steals the oxygen supply of other marine life in your pond.
Mixing, Dosing, and Application of Copper Sulfate
Copper sulfate for ponds exists in various forms一there’s crystal, liquid, and powdered forms. The form of copper sulfate you’ll use depends on what kind of algal growth you have in your pond.
Where To Buy Copper Sulfate for Pond Treatment
You can get your supply of copper sulfate crystals at your nearest agriculture retail store or order them from us online at Standish Milling Company. Make sure to buy the most suitable variation based on your pond size and algae problem.
The Bottom Line
Copper sulfate for ponds is an extraordinarily effective and cost-efficient way to treat your pond’s algae problem. However, use it with proper caution and management to avoid oxygen depletion, fish toxicity, and killing of other plant life through contamination.
How to remove copper oxide from a sulfate solution?
Method. place some sulfuric acid in a conical flask and warm it in a water bath. add a spatula of copper oxide powder to the acid and stir with a glass rod. continue adding copper oxide powder until it is in excess. filter the mixture to remove the excess copper oxide.
How to remove copper oxide from water?
filter the mixture to remove the excess copper oxide. pour the filtrate (the copper sulfate solution) into an evaporating basin. heat the copper sulfate solution to evaporate half of the water. pour the solution into a watch glass and leave to allow all of the water to evaporate.
Part A: Getting the copper sulfate
Copper sulfate is a chemical that’s commonly used as a fungicide, rootkiller and drying agent. You might find it in powder/crystalline form at Home Depot or your local gardening store. Alternatively, it is cheap and easy to find online.
Part B: Preparing the solution
Dissolve 50-55 g of copper sulfate powder for every 100 ml of very hot, but not boiling water.
Part C: Growing the seed crystal
Place your dish in an undisturbed location like a cupboard or a shelf in the storeroom. After a day or two, small beautiful crystals will have formed in it.
Part D: Growing the main crystal
As time passes, the crystals will slowly grow in size. But there’s a golden rule that you need to follow:
Part E: Storing the crystal
Copper sulfate crystals are bright blue because they contain water molecules inside their crystal structure. If left in the open, they might dehydrate, turning white.
How to apply copper sulfate?
1. Application by Dragging Under Water: By placing Copper Sulfate in a burlap or finer mesh bag, apply by dragging the bag attached to a boat or float so that bags are suspended in the top foot of water until the crystals are dissolved.
How far apart should you drag copper sulfate?
Drag the bag of copper sulfate first near the shoreline and continue outward by moving as the boat travels in parallel lines about 20 to 100 feet apart until area has been treated or until 1/3to 1/2 of the surface area has been treated.
Which counties in California have copper sulfate?
State law prohibits the use of copper sulfate in sewage systems in the State of Connecticut and in the following counties of California: Alameda, Contra Costa, Marin, Napa, San Francisco, San Mateo, Santa Clara, Solano, and Sonoma.
Can copper sulfate kill pondweed?
Should copper sulfate fail to control pondweeds satisfactorily, it may be necessary to either treat the ditch with a suitable approved herbicide or use mechanical means to remove excess growth. In either case, resume copper sulfate addition as soon as possible.
Is copper sulfate good for metal?
A saturated solution of plain copper sulfate crystals is an excellent mordant for zinc, aluminum, copper, brass and mild steel, but due to lack of a catalyst, etching is somewhat slow and the solution becomes exhausted quickly.
:max_bytes(150000):strip_icc()/copper-sulfate-crystals-58b5b6fb3df78cdcd8b33b4b.jpg)