how do you use an audio control epicenter

by Adolph Christiansen Published 3 years ago Updated 3 years ago

The Epicenter is fused at 1 amp, and ideally, if it can be powered directly from the car battery. Ground Connection Use the same gauge wire as for the +12V, and run it from the connector terminal marked “Ground” on The Epicenter to the battery’s negative terminal, or a good ground location used, for example, by the amplifier.

Part of a video titled Restore MISSING BASS with the AudioControl EPICENTER

1:38

2:47

That can handle even more power we simply adjust this setting for maximum base output. AndMoreThat can handle even more power we simply adjust this setting for maximum base output. And performance finally the epicentre logo here will activate whenever the epicenter circuit is activated.

Full Answer

What is the audio control epicenter?

The audio control epicenter is a bass processor that uses patented technology to accurately recreate and inject bass into its original signal path. It analyzes the music to look for information in higher-order harmonics to recreate the missing signal.

How to connect the epicenter with the amplifier?

Connecting the Epicenter with the amplifier is not difficult, but you must remember that it has to go between the amplifier and the stereo. You need the two RCA signal wires for signal transfer from the radio to the Epicenter and then further to the amplifier to make the connection.

How does the epicenter work?

How does the Epicenter work? The unique bass restoration circuit of The Epicenter®, originally patented by AudioControl, looks at the upper harmonics and uses them to digitally recreate low frequency fundamentals (original frequency) that have been lost through compression (MP3s), rolled-off, or simply removed (during mastering).

Can the epicenter be mounted on the dash?

Dash Mount Control The Epicenter is designed to be mounted anywhere in the vehicle, with the exception of the front bumper or radiator. It comes with a dash mountable control that allows you to enjoy the effects of The Epicenter without having to leave the drivers seat.

How does the audio control epicenter work?

The unique bass restoration circuit of The Epicenter®, originally patented by AudioControl, looks at the upper harmonics and uses them to digitally recreate low frequency fundamentals (original frequency) that have been lost through compression (MP3s), rolled-off, or simply removed (during mastering).

What should the sweep be set at on a epicenter?

The effective range of the sweep control is 27Hz – 63Hz. The factory setting is detented at 40Hz. Our suggestion is to start out at around ¾ to full clockwise rotation.

Is an epicenter the same as an equalizer?

We always recommend you put the Epicenter® BEFORE an EQ or crossover. Since the Epicenter is adding frequencies to your signal, you would want to put it before any EQ or crossover in order to be able to adjust those frequencies.

Does epicenter give more bass?

AudioControl's legendary bass restoration circuitry, The Epicenter, brings out the best bass in any system. Whether you like rock, jazz, hip hop, country, banda, classical, CD's, MP3's, or cassettes, you will love how The Epicenter makes your system sound. More Bass… Louder!!

How do you hook up a soundstream Epicenter?

Part of a video titled Soundstream Technologies - Digital Bass Reconstruction Processor

0:36

1:48

Connect 12 volt power remote turn on and ground using primary wire the included dash mounted gainMoreConnect 12 volt power remote turn on and ground using primary wire the included dash mounted gain control connects to the device.

What does wide mean On Epicenter?

The “Sweep” knob allows you to pick the center frequency that. you want The Epicenter bass restoration circuit to maximize. The “Wide” knob. adjusts how wide of a frequency range The Epicenter will effect.

Does epicenter help bass?

The centerpiece of many champion sound installation systems. A patented process digitally maximizes the ultra-low bass on all types of source material. The Epicenter detects bass harmonics, then digitally recreates the underlying fundamental for the incredible punch and impact of live music.

Which is better equalizer or crossover?

So by now, you know the difference between a crossover and an equalizer. While both of these components allow us our car sound, they work differently. While crossover splits an audio signal and sends it to relevant speakers, the EQ customizes the frequency output of a car audio system.Feb 12, 2022

Are AccuBASS necessary?

You need to figure out if your car has its bass rolled off or if it's a clean flat signal. If it's flat, you don't need Accubass. If it's rolled off, Accubass can be helpful. If you plan on getting a DSP in the future, just get the DSP.Jul 24, 2019

How do I adjust my Accu Bass?

How to setup AccuBASS®

Set the AccuBASS Threshold dial all the way to the left (counterclockwise)
Set the AccuBASS Level knob at the 12 O'clock position.
Start playing a 50 Hz test tone.
Slowly turn up the head unit volume until you start to hear bass dropping.

More items...

How much is the epicenter?

Compare with similar items

	This item AudioControl The Epicenter Bass Booster Expander & Bass Restoration Processor with Remote (Black)
Customer Rating	4.8 out of 5 stars (1644)
Price	$13999
Sold By	SkyHighCarAudio
Color	black

3 more rows

What is AccuBASS threshold?

The AccuBASS Threshold determines when the AccuBASS process turns on and the AccuBASS Level adjusts how much bass is restored. On the LC2i, the Threshold knob (screw) is located on the side of the unit between the Main and Bass RCA output connectors. A micro screwdriver will be needed in order to adjust it.

Why do you put the Epicenter before EQ?

Since the Epicenter is adding frequencies to your signal, you would want to put it before any EQ or crossover in order to be able to adjust those frequencies.

Can you connect an epicenter to a factory system?

If you are planning to integrate the Epicenter in your factory system, there are a couple of considerations. Either you would get the Epicenter Plus which has high speaker level inputs so you can connect directly to the output of the factory system, or you would connect the epicenter directly after your line converter, ...

Receiving Helpdesk