How do you install stair treads and risers over existing stairs?
- Use a circular saw to cut the treads to the length of each riser.
- Secure them to the stringers with wood screws.
- As you install one riser, position and fasten the corresponding tread so you can carefully climb to the next step for installation.
How to create and install stringers, risers and treads?
- Risers will not fit as well between treads
- You cannot fasten risers to treads
- Treads cannot be leveled using risers
How to install wood stair treads without showing nail holes?
- Nail gun and air compressor (you can rent it if you’re not using it often)
- Sliding compound miter saw (either you buy it, or you rent it)
- Power sander and fine-grit sandpaper
- Stair tread template
- 42″ oak stair risers. ...
- 42” oak stair treads (it’s what you’re stepping on). ...
How to install stair stringers properly?
What’s the installation process for stair stringers?
- Firstly, attach the bolt down or cast in connector to the base of the stringer pair and position them to where you will need them to go later.
- After they are correctly positioned, use M12 bolts to attach the top fixing bracket to the face of the deck structure (as shown).
- For cast in, fill the footing with concrete and leave to set. ...
How do I install trim around stair treads?
Proper Ways to Trim Stairways
- Different Types of Trim. The simplest type of trim is a quarter-round molding that covers the crevice between the riser, or tread, and the wall.
- When to Trim Your Staircase. If you are adding molding to each step, you must wait until the stairs are finished. ...
- Interior Staircase Trim. ...
- Exterior Staircase Trim. ...
Can you put stair treads over existing stairs?
Retro-fitting stair treads is the simplest solution for a DIY'er intent on installing hardwood treads over an existing flight of stairs. High-quality prefinished stair treads are made of solid edge-glued wood—not a veneered or engineered material—and can be used to “cap” or reface an existing tread.
How do you add risers to existing stairs?
0:467:53How to add risers to existing stairs - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can see I did one up here pocket hole screws on the top. And then I'll put screws straightMoreYou can see I did one up here pocket hole screws on the top. And then I'll put screws straight through the back into the back of the treads.
How do you install rubber stair treads over existing stairs?
0:053:55How to Install Rubber Stair Treads - YouTubeYouTubeStart of suggested clipEnd of suggested clipTo do this after we have our mark and cut our tape just simply pull the tread any distance from theMoreTo do this after we have our mark and cut our tape just simply pull the tread any distance from the edge that you're scribing to get it in place.
How do you overlay stair treads?
0:422:03StareCasing Hardwood Overlay System - Smart Contractor ProductsYouTubeStart of suggested clipEnd of suggested clipJust measure cut. And install the stair casing system is very versatile. And can be installed onMoreJust measure cut. And install the stair casing system is very versatile. And can be installed on virtually any carpeted or worn hardwood staircase.
How do you install treads and risers?
6:1117:31How To Install New Stair Treads And Risers For Under $25 EachYouTubeStart of suggested clipEnd of suggested clipIt was time to install the first riser. It's pretty simple these stairs were pretty good and square.MoreIt was time to install the first riser. It's pretty simple these stairs were pretty good and square. So I was able to just cut the link I think it was somewhere around 41. And a half inches. And I
How do you fill the gap between stair tread and riser?
Run a heavy bead of the silicone along the gap to fill it, and then use a wet fingertip to smooth it out if necessary. It's the fastest way to fill minor gaps, and if you're not happy with the way it looks, you can always install molding over it.
Do you install stair treads or risers first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser. Treads and risers fasten with construction adhesive to the subfloor.
What adhesive do you use on rubber stair treads?
Neoprene Contact Cement is a quick-drying solvent based adhesive that can be applied to all rubber and vinyl stair treads to concrete, pan filled, wood, metal, marble and terrazzo steps. Works well for vinyl and rubber stair treads.
How do you secure a rubber stair nosing?
0:584:33Stair Nosing by Johnsoite Installation - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe stair nosing onto the step for proper adhesive placement brush 9:45 contact bond adhesive inMoreThe stair nosing onto the step for proper adhesive placement brush 9:45 contact bond adhesive in between your reference lines on the step edge and the back of the stair nosing.
How do you reface stairs?
0:5310:20DIY Stairs Makeover for Under $200 with Full Cost Breakdown!! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo I start off by eliminating the connection between the drywall and stairs by adding a 1-inch pieceMoreSo I start off by eliminating the connection between the drywall and stairs by adding a 1-inch piece of trim to the top of the stringer.
How do you update a staircase?
Add fabric. Stair runners or stair rugs can both upgrade the look of your stairs and provide you with a comfy place to put your feet. ... Use a stencil. ... Add underside color. ... Paint the steps. ... Add candles. ... Use baskets. ... Build in storage. ... Paint the wall.More items...•Mar 16, 2020
How do I make my stair treads deeper?
3:377:25How To Increase Individual Stair Step Depth For The Entire StairwayYouTubeStart of suggested clipEnd of suggested clipLike if we wanted to increase the individual tread run by an inch we would actually need to add oneMoreLike if we wanted to increase the individual tread run by an inch we would actually need to add one inch to each step working our way down.
What is the cost to install stair treads and risers?
For how beautiful they look, you’d think they were really expensive. At least a few hundred, right?
Step 1: Remove the old stair tread material (i.e. carpet, vinyl, etc.)
Remove any old covering layers if you can – try and get back to the bare wood if possible. We didn’t, as I think that the bottom layer has a whiff of asbestos about it. We’ll just leave it there.
Step 2: Trim the plywood stair tread to size
Notch the ends of the tread overhang. This will allow you to cut it off and ensure a clean fit for your new tread
Step 3: Start Attaching the Stair Treads
With the overhang removed, your new risers can go right to the top of the old stair.
Step 4: The Tricky Part – Where the top floor and stairs meet
When you reach the top step, you are going to have to do some fancy cuts to notch in a small piece of the tread to match the level with your new floor.
More in our Mudroom Makeover
How we carved out space for a tiny but super functional built-in mudroom in this small landing – we’ve got tips on how you can find potential storage too!
How much does a pine tread cost?
You may find pine treads for $11/piece, and oak models for as high as $16/piece. You will need some clear polyurethane and stain (when you don’t want to stick with the natural color of wood). A natural bristle brush as a nylon type isn’t a good choice for the polyurethane (it’s based on oil)
Can you cut carpet at the top of stairs?
Ripping up the carpet and the underlay (it goes fast) helps you blow some steam off, though. If the carpet goes all the way to the upstairs landing, it’s better that you begin with cutting it at the top of the stairs.
Can you tape off stairs?
It’s almost never a wise idea. Since the treads are cut so tightly, the chances are that they will scrape up the trim when you fit the treads and risers as needed. However, you may tape off the stairs, painting the trim instead. Use two coats of paint, generously.
How long does it take to install prefinished stair treads?
In other words, half the work is done for you, so installation takes only about 15 minutes per tread.
How deep is stair tread?
Standard tread depth is 11-1/2 inches, and a variety of widths are available to meet your specifications. Additionally, Stair-treads.com is not simply a distributor but also the tread manufacturer, and the company will custom-stain the treads to your flooring.
What are the advantages of prefinished stair treads?
The primary advantage of using the prefinished stair treads is the ease of installation. For example, the stairs shown in this article were built of lumber and covered with carpet. Once the carpet was removed, the raw lumber tread was revealed and it was downright ugly.
What is retrofitting stair treads?
Retro-fitting stair treads is the simplest solution for a DIY’er intent on installing hardwood treads over an existing flight of stairs. High-quality prefinished stair treads are made of solid edge-glued wood—not a veneered or engineered material—and can be used to “cap” or reface an existing tread. The primary advantage of using the prefinished stair treads is the ease of installation.
How do I cut bull nose off of a stair tread?
One way is to cut it off. Using a handheld circular saw or jigsaw, cut the bull nose of the tread back flush with (or slightly behind) the existing riser.
Do you have to remove old lumber treads when refacing stairs?
By refacing the stairs with the new prefinished treads, there was no need remove the old lumber tread. This is a particularly important advantage when dealing with “pre-fab” staircases that are built in a factory and delivered to the jobsite during construction.
Can you cut a riser with a miter saw?
Risers can be cut to length with a miter saw, handheld circular saw, or even a hand saw. I had to rip the risers to width, which is a little trickier. It’s possible to rip the risers with a handheld circ saw with an edge guide, but you’ll get the most accurate results using a table saw with a rip fence.
When installing stair risers, do you install the treads first?
In this article, when we say “install stair risers first”, it doesn’t mean install all the risers first before the treads. It means that you first install the bottom two risers. Then you install the first tread, which fits above the bottom riser and against the riser behind the tread. After installing a stair riser, ...
How do I install stair treads?
Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser. Treads and risers fasten with construction adhesive to the subfloor. There are many different types of stair treads, and some will offer different methods of installation.
Why do you need to install a riser first?
Stair stringers are not always level, so if you install the tread first, you will have to shim it accordingly if your stair stringers are out of level. By installing the riser first, you can use your level to bring your riser to a height to ensure your stair tread is level.
Do you need adhesive for stairs?
The adhesive is the most important part of your install – and don’t be shy when using it. Remember, stairs withstand major abuse, so you want them to be rock solid. You’ll also need access to the back of your stairs to screw through the subfloor into the risers and treads.
Is it easier to install risers or treads?
Ease of Installation. While installing treads first might seem more straightforward, it is easier to put your risers first and then treads. Regardless of what order you install your treads and risers, your tread installation will take more time.
Can you screw a stair tread into a subfloor?
Then the stair tread fits snug against the riser – not the subfloor or stringer. Therefore, you can go behind your stairs and screw through the subfloor and riser and into the stair tread. Now you have fastened the riser and tread together into the subfloor. This will result in a much stronger connection.
Can you go behind a stair riser?
Installing risers first results in a more long-lasting set of stairs. The primary reason is that when you install risers first, you can cut them to fit the entire face of the stair riser, from top to bottom. Then the stair tread fits snug against the riser – not the subfloor or stringer. Therefore, you can go behind your stairs ...
How deep should a stair tread be?
Allowing for a 1 1/2-inch overhang, the minimum depth of the stair tread must be at least 10 inches. Cut the tread to the exact size needed using a miter saw. The blade of the miter saw must cut the wood on ...
Can a miter saw cut through a stair tread?
The blade of the miter saw must cut the wood on the waste side of the marked line or your stair tread will be too short. Do not cut through the line or on the measured side of the tread. Both mistakes will leave you with a wasted stair tread.
Ordering Supplies
To start, you'll have to order the stair treads. Treads can range anywhere from $20 to $100 or more depending on the type of tread that you order. Plain, unfinished treads are the cheapest, but you'll have to finish the wood yourself at home. Mitered and altered treads are more expensive.
Hiring a Contractor
Some contractors offer a free estimate, and they'll visit your house and give you a quote for the project. If they charge per stair, you can expect to pay $100 or more for each tread and riser that they install. The total usually comes to over $1,000. Other contractors charge by the hour, which typically comes to $150 or more per hour of work.
What's the Overall Cost?
On average, the cost of installing treads and risers can range from $5,000 to $8,000. However, this isn't an exact price. Get in touch with contractors in your area to learn about the cost to add risers to open stairs.
Can You Save Money by Installing Your Own Treads and Risers?
You could save thousands of dollars by installing your own treads and risers. However, you'll still have your own labor costs. Time is one of the biggest costs — you'll have to put everything on hold and set aside a day or two to complete the project. Contractors work more quickly because they install new stairs every day.
Order Stair Treads and Risers From Stair Part Pros
When you need supplies for your upcoming project, check out our selection of stair treads and risers. Looking to build a new set of stairs or redo an existing staircase? Browse our selection of box newels, skirtboards, moldings, brackets, iron shoes, stairwells and everything else you need to start from scratch.
