Receiving Helpdesk

how do you change the water inlet valve on a maytag bravos washer

by Cesar Bergnaum Published 3 years ago Updated 3 years ago

Part of a video titled How To: Whirlpool/KitchenAid/Maytag Water Inlet Valve ...
6:37
14:17
Into the washer. Once you have both screws out we can lift the water inlet valve assembly out of theMoreInto the washer. Once you have both screws out we can lift the water inlet valve assembly out of the washer.

How to replace the water inlet valve on a Maytag washer?

How to Replace Your Maytag Washer’s Water Inlet Valve Assembly. 1. Unplug the washer and turn off the water supplies. First, unplug the washer. This should be the first thing you do before starting any appliance ... 2. Disassemble the machine to access the water inlet valve assembly under the ...

What is a Maytag Bravos water supply valve?

The Maytag Bravos water supply valve is a very large assembly of six solenoids that direct water through the detergent, bleach, and fabric softener dispensing cups as well as directly into the washer’s tub through the “fresh fill” inlet valve.

How does a Maytag Bravos washing machine work?

Like most electronically controlled appliances, Maytag Bravos Washing Machines use a part called the user interface which is a thin panel of switches placed directly behind the skin of the washer’s control console and also a switch called the encoder that identifies the position of the rotary cycle selection knob.

How do you replace a water inlet valve on a refrigerator?

Replace the water inlet valve. Orient the new part with the solenoids on the top and the water connections on the bottom. line it up with the holes and press it firmly into position. Secure it with the two screws you removed earlier.

How do you change the water inlet valve on a Maytag Bravos?

0:532:06How to Replace the Water Inlet Valve on a Maytag Vertical ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd remove the two hex head screws that hold the valve. Pull the water valve out of the washer. SetMoreAnd remove the two hex head screws that hold the valve. Pull the water valve out of the washer. Set it aside for disposal push. The new water valve into position reinstall the mounting screws plug.

How do you change a water valve on a Maytag Bravos XL?

How to Replace Your Maytag Washer's Water Inlet Valve AssemblyUnplug the washer and turn off the water supplies. ... Disassemble the machine to access the water inlet valve assembly under the console. ... Remove the water inlet valve assembly. ... Replace the water inlet valve. ... Install the new wire harness. ... Reassemble the machine.

How do you remove the Maytag inlet valve?

2:096:12How To: Whirlpool/KitchenAid/Maytag Water Inlet Valve WP8540751YouTubeStart of suggested clipEnd of suggested clipOnce you have the clamp moved up we can pull the hose off the water inlet valve get the hoses onMoreOnce you have the clamp moved up we can pull the hose off the water inlet valve get the hoses on there type you can use a small flat-head screwdriver to help pry. It.

How do I know if my water inlet valve is clogged?

Signs pointing to a faulty inlet valve include:Leaks that fill the dishwasher when it's off.Inadequate water for a cycle. ... A bad inlet valve can lead to leaks from the dishwasher onto the kitchen floor. ... Most inlet valve malfunctions stem from a defective seal or solenoid failure.

How do you change a water inlet valve?

0:262:08Replacing the Water Inlet Valve on a Front-Load Washer - YouTubeYouTubeStart of suggested clipEnd of suggested clipUse a Phillips screwdriver to remove the two mounting screws remove the old water inlet valveMoreUse a Phillips screwdriver to remove the two mounting screws remove the old water inlet valve assembly. Position the new water inlet valve assembly lining.

Why is my Maytag Bravos washer not filling with water?

If your Maytag washer is not filling, check your fill hoses: Check household faucets. Hot and cold water supply lines must be connected and turned on. Check for kinks in inlet hose.

How do you test a Maytag inlet valve?

1:552:50Washer Not Filling? Water Inlet Valve Testing, Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipDisconnect the hot and cold water supply lines from the inlet valve and hold them over a bucket or aMoreDisconnect the hot and cold water supply lines from the inlet valve and hold them over a bucket or a washtub.

Why is my Maytag washer dripping water inside?

The tub seal might be torn, causing water to leak from the seal. If the tub seal is leaking water, water may leak through the tub seal and into the tub bearings. This can cause the bearings to fail. For this reason, if the tub seal is leaking water, replace both the tub seal and the tub bearings.

Why is water dripping inside my washer?

If your washer drips water or fills with water when it is not turned on, the water valve on the back of your washer may have failed. This can cause water to leak from the water valve into your washer tub when the washer is turned off. In this situation, the water valve usually needs to be replaced.

How do I know if I need a new water inlet valve?

8:1410:09How To Test A Dishwasher Water Inlet Valve (The Right Way) - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf no water comes out of the valve. Or if the water flow seems restricted or slow then you shouldMoreIf no water comes out of the valve. Or if the water flow seems restricted or slow then you should replace the valve.

How do you unclog a water inlet valve?

0:241:37Clogged Screens/Water Inlet Valve - EASY FIX - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhatever do grab some kilowatts or pliers and slowly unscrew this water will come out. And once itMoreWhatever do grab some kilowatts or pliers and slowly unscrew this water will come out. And once it is all the way.

How can you tell if a water valve is bad?

If you have no water pressure throughout the house on both the hot and cold, your PRV may be bad. Make sure you check both the hot and cold water. If there is good pressure on the cold and not the hot it may be an issue with the water heater or the fixture itself.

What is the water inlet valve on a washing machine?

The water inlet valve on your washing machine is the part that the connect the two water hoses to the machine, and it controls the flow of both hot and cold water. Replacing a bad valve is a simple job and must be done with parts and procedures that are specific to your washing machine model. Why is my washer leaking?

How to clean water inlet screens?

Remove the water inlet screens with your finger or a pair of needle-nose pliers. Brush out any dirt or grit. You can soak the inlet screens in a mild solution of water and vinegar if they are calcified. Insert the clean water inlet screens back into the inlet valves on the washer.

How to tell if a washer is leaking water?

If you have water leaking from the washer during a wash or drain cycle, check the area of the drain pump. Look for signs of a loose hose clamp or a leaking hose connected to the pump first. If the leak is originating from the pump, you will need a replacement pump.

What is the inner basket on a Whirlpool washing machine?

Most washing machines have an inner basket that is directly attached to the drive system at all times.

What is the suspension system on a Cabrio washer?

The suspension system on the Cabrio, Bravos, and Oasis washing machines is about as simple as it gets. The outer tub is suspended on four spring-loaded suspension rods. This design enables the washer tub to absorb a great deal of vibration and shock by using the weight of the tub as a counterbalance.

What is the drain pump on a Whirlpool Cabrio?

The Drain pump of a Whirlpool Cabrio, Maytag Bravos, or Kenmore Oasis washing machine is essentially the same as the recirculation pump except it’s purpose is to remove dirty wash water from the washing machine’s tub and send it packing down stream. Because the water level is being monitored by the pressure sensor built into the washing machine’s control board, if the washer takes to long to drain an “ Ld ” meaning “Long Drain” error code will appear on the washer’s display. Another common drain related error code is “ Sd ” meaning “Suds Detection” (For more information about troubleshooting these error codes click on the code link) Like all washing machines it is important to check your pockets for loose change and put smaller items such as baby socks and lingerie into a mesh laundry bag to keep them from finding their way into the drain pump or recirculation pump.

What is a control board on a washing machine?

All electronically controlled washing machines use a control board to process commands entered into the user interface and send the proper amount of electricity to a particular washer component at the correct time to perform some function, such as opening a particular water valve solenoid, operating the motor, energizing the recirculation pump, drain pump or lid lock. If the washing machine were a body the control board is the brain behind all of the washer’s operations.

Why does the air pressure in a washing machine increase?

As the water level rises , air pressure inside the “pressure transducer” tube increases because of the water’s weight. When the desired water level is reached, the pressure transducer inside the washing machine’s control board cuts electricity to the water valves and turns on the recirculation pump, for the wash portion of the cycle.

Why is my washing machine control failing?

The most common cause of any control failure is corrosion on the connectors. Always check for a good electrical connection first! Also look for broken or looses wires, bad terminals, or wires not pressed onto connectors far enough before replacing any washing machine parts.

Why does the inner basket rotate?

Because the inner basket is free floating it will tend to rotate with the water and clothing it contains which the agitator or impeller is turning. This catch up then slow down movement creates an additional wash action used to free dirt from clothing. The basket hub is a two-part component.

1. Unplug the washer and turn off the water supplies

First, unplug the washer. This should be the first thing you do before starting any appliance repair procedure. Then turn off the local hot and cold water supplies. During this repair, you may need to pull the washer away from the wall so you can more easily access the rear of the appliance.

2. Disassemble the machine to access the water inlet valve assembly under the console

First, you will need to flip the top panel of the washer over. To start, tape the lid down securely. Next, depress the two tabs between the top panel and body of the machine. Pry a putty knife about six inches inward from each front corner to press each tab. Once both are open, swing the door up.

3. Remove the water inlet valve assembly

Start removing the wiring harness. To do that, move to the left side of the console and cut the zip tie holding the left bunch of wires. Locate the thermistor that’s plugged into one of the plugs facing the back of the machine. It has two blue wires.

4. Replace the water inlet valve

Orient the new part with the solenoids on the top and the water connections on the bottom. line it up with the holes and press it firmly into position. Secure it with the two screws you removed earlier.

5. Install the new wire harness

Your part may have come with a new wire harness with the water intel assembly has a newer type of solenoids. Whether you’re using a new wiring harness or reusing the old one, the steps are the same:

6. Reassemble the machine

Line up the five mounting tabs at the interior edge of the console with the body of the washer. Then flip the console over and click the three back tabs with the screws into place. Tighten the screws to secure the console.

What is the water inlet valve on a washing machine?

The water inlet valve on your washing machine is the part that connects the two water hoses to the machine, and it controls the flow of both hot and cold water. A problem with the valve can cause the washer not to fill properly or not fill at all.

Why is my washer not filling?

Malfunctions in the water inlet valve can cause a washer to not fill properly, fail to run, or wash at the incorrect water temperature. Fixing a water inlet valve is a matter of systematically examining the parts until you find the problem. Sometimes the fix will be simply cleaning the filter screens, but it can also require replacement ...

Can you repair a washing machine valve?

There is little that you can do to repair the valve itself, but you can clean the two inlet ports to restore full water flow. You can also test the valve to determine whether it has failed. Replacing a bad valve is a simple job and must be done with parts and procedures that are specific to your washing machine model.

How to stop water from flowing in washer?

Water inlet hose. Check for any kinks in inlet hoses, which can restrict water flow. If possible, remove the inlet hoses from the back of the washer. To do this, turn the water supply off, then use pliers to remove the hoses. Place hose ends in a bucket to catch water remaining in the hoses. Check the inlet screens on the back ...

How to save energy by not connecting to hot water line?

If you want to save energy by not connecting to the hot water line (or only have access to a cold water line if connected in a garage, etc.), purchase a “Y-connector” and an extra inlet hose to connect the hoses to both sides of the water valve.

How to clean a clogged water hose?

Check the inlet screens on the back of the water inlet valve. If they appear to be clogged, scrub thoroughly with a brush (an old toothbrush works great) and mild soap and water.

How long does it take for a washer to reset?

If the unit is unplugged before turning off the power, the washer will go into a reset mode, which will take approximately 10 minutes to complete. You may hear the pump running, and the door will unlock after about 10 minutes.

Can a washer run with only one incoming water?

The washer will not properly operate with only one incoming source of water. The water valve inside the machine needs to have the “pressure” from both attached hoses in order for the washer to complete the cycle. If a cold water wash is selected, the washer is designed to add hot water to keep the temperature optimal for cold wash performance. ...

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9