How to Troubleshoot a Roper Dryer That Will Not Start
- 1.. Confirm that the dryer's power cord is connected to a grounded outlet. Unplug the cord and examine it for any damage...
- 2.. Verify the circuit breaker to the dryer circuit has not tripped. In the electrical service panel for your home, look...
- 3.. Check for a blown fuse in older homes that have fuse boxes. The...
Full Answer
Why is my Whirlpool dryer not starting?
Why Your Whirlpool Dryer Is Not Starting?
- Solution. Whichever the case, a loose door latch will not let your whirlpool dryer start. ...
- Solution. If you are experienced enough, you can first use a multimeter to check the power connections to confirm the issue.
- Solution. ...
- Solution. ...
- Solution. ...
- Steps of replacing a whirlpool dryer thermal fuse. ...
- Solution. ...
- Solution. ...
- Solution. ...
- Solution. ...
How to repair a dryer that will not start?
- Unplug the dryer from the outlet. This is important! ...
- Note where the start switch is and label the 2-3 wires leading to it with electrical tape to ensure you can reattach them exactly as they are. ...
- Use your multimeter to test the start switch for continuity. Set the multimeter to measure resistance with a scale of Rx1. ...
Why is my dryer not turning on?
How to test your dryer’s drive motor:
- After unplugging your dryer, locate the motor by opening your dryer’s cabinet. ...
- Using pliers to pull on the metal leads and not the wires themselves, remove the motor from the dryer.
- Set your multi-meter to the Rx1 setting and touch the terminals with the probes. ...
Why is my Hotpoint dryer drum not turning?
WHY WON'T MY DRYER SPIN?
- DRIVE BELT. A worn, slipped, or broken drive belt creates a distinctive problem: the dryer motor will be humming as usual, but the drum won't turn.
- DRUM ROLLERS. Most dryers are equipped with two drum support rollers—as well as accompanying axles, glides, and bearings—that allow the drum to spin as freely as possible, reducing strain ...
- DRYER MOTOR. ...
What would cause a Roper dryer not to start?
On most dryers, when the dryer belt breaks, the motor will still run, but the drum will not turn. However, some dryers have a switch that shuts off power to the dryer if the drive belt is broken. Check the dryer belt to determine if it is broken. If the belt is broken, replace it.
How do you reset a Roper dryer?
Firmly push the switch all the way to the "Off" setting and then firmly push it back to the "On" setting. A correctly reset breaker emits a snapping sound when turned back on. If there are two circuit breakers, check both switches.
When I push the start button on my dryer nothing happens?
If the dryer start switch does not have continuity when it is activated, it will need to be replaced. The door switch is located near the dryer door and is activated when the door is closed. If the door switch fails, the dryer won't start at all. Most door switches will make an audible click when they are activated.
Why won't my dryer start but has power?
If the motor relay loses the electrical current from the control board, the relay will trip and stop supplying power to the motor. That means the dryer won't start or operate. Typically, the relay is damaged in these cases and will need to be replaced before the motor can receive the signal to operate again.
Where is the dryer reset button?
Generally speaking, you would reset a dryer by pressing the reset button that is located on the control panel. This will help to clear any issues that may be happening with the dryer. It may be necessary to wait until the motor cools down before you push the reset button, but it should fix most problems.
How do I know if the thermal fuse is blown?
To test if your thermal fuse has blown, touch the right side of your multimeter lead to the right side of the fuse, and repeat with the left multimeter lead. If the multimeter needle fails to move, this indicates the thermal fuse has blown.
How do I know if my dryer start switch is bad?
As a safety feature, the dryer will not work with an open door. When the switch is broken, it is unable to tell the control panel the door is shut, so the dryer will not turn on. The only way to tell if the switch is faulty is to take it out of the dryer and test it with a multimeter.
How do you check a dryer start switch?
1:141:56Dryer Won't Start? Two Terminal Switch Testing, Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou begin make sure the switch you're testing has been removed or isolated from the appliance use aMoreYou begin make sure the switch you're testing has been removed or isolated from the appliance use a probe to touch one of the switches terminals and the second probe to touch the other terminal.
Where is the thermal fuse?
Thermal fuses are installed on the dryer's exhaust duct. Typically, you must remove the back panel of a dryer to access the fuse. Ensure to shut off electrical power to the dryer before attempting to locate and troubleshoot the fuse.
How much does it cost to replace a dryer thermal fuse?
Other Costs to Fix a DryerPartMaterial CostTotal CostThermal fuse$5 - $10$80 - $130Dryer thermostat$3 - $20$180Bearing$50$130 - $250Roller$10 - $30$90 - $2301 more row
Why does my dryer not stay on?
All dryers stop when the door opens or the door switch detects the door opening, so a broken door strike, weak door catch or faulty door switch can cause the dryer to stop mid-cycle. A bad drive motor, failed timer or faulty electronic control board can also stop the dryer before the cycle ends.
Why won't my dryer start?
If the door stays ajar or some item prevents the door from staying closed, the dryer will not start. Keep the door closed by firmly pressing against the door until you hear a click sound. Avoid slamming the door to minimize wear and tear.
How to check if dryer circuit has tripped?
Firmly push the switch all the way to the "Off" setting and then firmly push it back to the "On" setting. A correctly reset breaker emits a snapping sound when turned back on. If there are two circuit breakers, check both switches.
How long is the Whirlpool dryer warranty?
As your dryer ages, possible replacement parts include a heating element, a lid switch assembly or a blower fan. Whirlpool offers a one-year warranty.
Can you use a dryer if the cord is damaged?
Arrange repairs with a qualified service technician authorized to do Roper repairs. Do not use the dryer if the electrical cord is damaged, and do not attempt to repair a damaged cord with electrical tape; have the cord replaced. If the outlet fails to work after you reset the breaker or replace the fuse, your home might have an electrical hazard.
My Repair & Advice Featured Story
I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad.
My Repair & Advice Featured Story
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping.
My Repair & Advice Featured Story
Background: Roper Electric Dryer model REX6634RQ0 purchased new in early 2006 by my wife. Dryer use profile is low to moderate as it was used by only one person (working from home) from 2006 to late 2007 then moved and stored in a dry basement until mid 2009.
My Repair & Advice Featured Story
I realized my load of laundry was still wet after a normal drying cycle. My first action was to turn the dryer on (2010 gas Maytag centennial) and open the front port to look at the ignitor coil. It never turned orange so I knew there must be a problem with the primary circuit.
My Repair & Advice
Looked up the part on your website. Ordered the part, watched the video, and it was fixed in 10 minutes.
My Repair & Advice
I temporarily wired the two outside wires together to use the dryer. The dryer would not shutoff when you open the door and the light would not come on. The switch enables the dryer to work one way and turns on the light and turns off the dryer the other way. Replacing the part was really easy.
My Repair & Advice Featured Story
My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping. My thing was: I would turn it off and turn the drum by hand about halfway around and it would work again.
Why won't my dryer start?
When a motor goes bad, there is usually a slight humming sound coming from the motor as it tries to rotate the shaft and pulley that spin the drum.
What happens if my dryer doesn't work?
A: When dryers fail to operate properly, it’s a huge inconvenience. Gone are the days of stringing up yards of clothesline and hanging the family’s clothes on display, but this means that when the dryer isn’t working , you’re out of luck.
What is a relay in a dryer?
A motor relay is a lesser-known part present in some dryers that helps the drive motor operate as long as it’s receiving sufficient electricity as determined by the control board. It’s designed to help prevent electrical overloads and potential ensuing fires.
How to stop a dryer from overheating?
Keeping vents and hoses regularly maintained can help prevent a dryer from overheating. If it turns out that the dryer vent has been clogged for some time, a technician can test the thermal fuse to see if it’s gone out. It’s a common fix, so they’ll likely have a replacement part available. Photo: depositphotos.com.
What happens when the timer goes out on a dryer?
When the motor switch goes out, a dryer won’t start, continue running, or advance the time. Replacement is the only option for a defective timer.
What happens if a dryer relay is damaged?
Typically, the relay is damaged in these cases and will need to be replaced before the motor can receive the signal to operate again.
Why does my dryer not start when the thermal fuse blows out?
It’s also a common cause of dryer issues. When the thermal fuse blows out, the dryer won’t start, which is a safety precaution to prevent a fire. Sometimes thermal fuses go out due to clogged dryer vents.
Why does my dryer stop mid cycle?
If the drum bearing is worn out, it may put too much strain on the motor, causing the dryer to stop mid-cycle or not turn at all. To determine if the drum bearing is at fault, remove the dryer belt and try turning the drum by hand. If the drum rotates freely, it is unlikely that the drum bearing is worn out.
How to tell if dryer drum bearing is worn out?
To determine if the drum bearing is at fault, remove the dryer belt and try turning the drum by hand. If the drum rotates freely, the drum bearing is not likely worn out.
How to tell if support rollers are worn out?
To determine if the support rollers are worn out, remove the belt from the dryer and try turning the drum by hand. If the drum does not... rotate freely, check the support rollers for wear. If the rollers spin freely without wobbling, they do not need to be replaced.
What are drum glides on a dryer?
The drum glides are small plastic pieces that support the front of the dryer drum. As the drum rotates, it slides on these plastic pieces. Over time, the drum glides wear out. If the drum glides are worn out, the drum can start binding and put strain on the motor.
How many rollers does a dryer have?
Most dryers have two drum rollers on the rear of the drum, and some dryers have two more rollers supporting the front of the drum. The rollers must spin freely to work properly. If the drum rollers are worn out, the dryer won’t turn properly.
What to do if drum does not rotate?
If the drum does not rotate freely, check the support rollers for wear. If one or more of the rollers are worn out, we recommend replacing all... of the rollers at the same time as a preventative measure. (The roller shaft can often be reused if it is in good condition.
How to fix a humming motor?
First, check the motor to see if it makes a humming noise. If the motor still hums, remove the belt from the motor and check the blower wheel to ensure that it is not obstructed. Next, with the belt removed, try rotating the drum by hand. If the drum does not rotate freely, determine what is causing the drum to bind.
Why won't my dryer start?
So it’s possible that your dryer won’t start because the signal that the door’s really closed isn’t being sent. Depending on your model, you’ll usually find the switch poking through the front panel into the dryer door frame. Unplug the dryer, and use your multi-meter ...
Why is my dryer not running?
If your dryer is not running, it could be that this fuse is broken, malfunctioning, or has been tripped by high heat.
What does it mean when the thermal fuse goes off on a gas dryer?
Keep in mind that if this safety device has gone off, it usually means that the dryer has gone above its safe level of heat, and so it might be good to see if one of the other thermostats has failed.
Why does my dryer make a humming noise?
The dryer drum is turned by a motor, which also operates the dryer’s blower. A broken motor may have been making a humming noise if a switch or winding has gone bad. The test to see if the motor is not working requires live voltage sent to the motor terminals, so this is a job for a service technician.
What does it mean when a wire overheats?
Any signs of wires or terminals that have overheated are warnings that the terminal block has loose connections that could overheat and possibly cause a fire. Repair or replace any damaged wires, but if the terminals themselves have overheated, you’ll need to replace the terminal block.
Why won't my Whirlpool dryer turn on?
As a safety precaution, a Whirlpool dryer doesn’t turn on if the door isn’t closed and latched. Even if the door appears closed, gently push to make sure it’s latched. Confirm that all clothing is in the dryer and that trapped items aren’t preventing the door from closing correctly.
Why is my dryer not drying clothes?
If there is a part malfunction when your dryer isn’t drying clothes a blown thermal fuse is often the cause. A dryer’s thermal fuse will trip to prevent the dryer from overheating, cutting power to the dryer. While a thermal fuse can malfunction over time, clogged dryer vents are a common trigger that blows the fuse.
How to check if dryer is receiving enough electricity?
To make sure your dryer is receiving adequate electricity here’s how to evaluate your incoming power: Make sure the dryer is correctly plugged into the proper electrical outlet. Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses. Avoid using an extension cord.
How to check if Whirlpool dryer is working?
Sometimes a Whirlpool dryer not starting is more of a power issue than a dryer malfunction. To make sure your dryer is receiving adequate electricity here’s how to evaluate your incoming power: 1 Make sure the dryer is correctly plugged into the proper electrical outlet. 2 Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses. 3 Avoid using an extension cord. Most extension cords can’t safely transmit the electricity required to power a dryer.
Why is my dryer not making a noise?
It could be because the dryer start switch is faulty. If the dryer doesn’t make any noise or motion when pressing the start button it’s likely the start switch is the problem. If multimeter testing confirms a lack of power to the switch it requires replacement. Image from Sears Parts Direct. #6.
Can you use an extension cord to power a Whirlpool dryer?
Avoid using an extension cord. Most extension cords can’t safely transmit the electricity required to power a dryer. #2. Problem with Whirlpool Dryer Settings. If your Whirlpool dryer won’t start but has power, confirm that you’ve selected the right dryer settings.
