If your Samsung washing machine is flashing a DC error code on the display, it means that the load in the washer is unbalanced. This occurs when you overfill the drum with clothes. This makes it difficult for the drum to spin The same thing also happens if you don’t put enough clothes when washing.
Why is the light blinking on my Samsung washer?
Some errors that can cause the lights to start blinking on your Samsung washer include: Not Filling: appears when water isn’t entering the washer properly. Hot or Cold: appears when the supply hoses for the cold and hot water have been accidentally swapped. No Drain: appears when water is not draining from the machine at all or slowly.
Why is my Samsung washer washing too much water?
The water inlet valve in the washer will only shut off at a minimum of 20 psi. If there’s inadequate pressure on the inlet valve, it may not close fully when it should, leading to more water in the washer. The “out of balance protection” feature in some Samsung washers leads to more water being added during a spin cycle if it suspects a small load.
Why is my Samsung washing machine running in a loop?
Most Samsung washing machines come with different faucets for hot and cold water. If the machine works fine but gets into a loop in the rinse cycle, it could be a sign of some issue with the cold water faucet.
Why does my washing machine keep turning on and off?
As you’ve seen above, the water inlet valve is important to each washing cycle. If it is not letting in enough water to complete a cycle, it can cause the machine to keep increasing the time. Check the valve as recommended above, to rule out any problems with it. A glitch in the control panel can cause the cycle timer to malfunction.
Why do the lights keep flashing on my washing machine?
If your washing machine detects an unbalanced or excessive wash load this will cause the spin light to flash. New machines will try to redistribute the load – but you may have to do this manually.
How do I reset my Samsung washing machine?
How to reset Samsung washing machine eco bubble (steps)Step 1: Turn on the washing machine. You clearly simply need to press the power button to make it turn on.Step 2: Press the option button. Next, press the option button on the machine for about 5 seconds. ... Step 3: Turn the dial to factory reset. ... Step 4: Tap to reset.
What are the codes on a Samsung washer?
Samsung Front-Load Washer Error CodesFault CodeWasher ProblemLELow water level during cyclesOEOverflow or too high water levelsnF1Hot and cold water lines are reversedtEWater temperature is either too high or too low13 more rows•Apr 14, 2022
How do I fix the code on my Samsung washing machine?
Occasionally, the UR error code is caused by a fault with the electronic controller, which has mistakenly identified an unbalanced load error when there is none. Resetting the washer by disconnecting the power to the washer for 10 minutes should fix the issue.
Why is my Samsung Washer not starting?
If the electrical outlet is receiving power, but the washer won't start, the power cord might be defective. However, this is very rare. To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.
What are washing machine error codes?
Error Codes in my Whirlpool Front Load WasherError CodeErrorrL or F34Items were detected in the washer during the Clean Washer cycle.Sud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,7 more rows•Apr 11, 2022
How do I reset my washing machine?
1:243:47The machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
Are there problems with Samsung washers?
There has been a recall on Samsung front load washers because water leakage onto the electrical connections of the washing machine's thermal sensor can cause an electrical short and ignite the circuit board, posing a fire hazard to consumers.
How do you do a factory reset on a washing machine?
If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
How do I reset my Samsung washer door lock?
Normally waiting for the cycle to end is all you need to do to unlock the door, or turn your washer on if it's off. If you get stuck, though, you can drain the water from front load washers using the emergency drain hose; once the water is gone, the door will unlock.
Samsung Washing Machine Is Flashing DC
If your Samsung washing machine is flashing a DC error code on the display, it means that the load in the washer is unbalanced. This occurs when you overfill the drum with clothes. This makes it difficult for the drum to spin The same thing also happens if you don’t put enough clothes when washing.
Samsung Washing Machine Is Flashing NF
If your Samsung washing machine is flashing the error code NF, it means that the machine isn’t getting water. This indicates that there is an issue with the water supply. Here’s how to fix this problem…
Why Is My Samsung Washing Machine Flashing SUD?
If your Samsung washing machine is flashing the error code SUD (often read as 5UD), it means that there is excessive foaming going on in the washing machine’s drum. Most times this happens when you use the wrong type of detergent when washing.
What Does The Red Lock Mean On A Samsung Washing Machine?
The red lock symbol on a Samsung washing machine is the Child Lock indicator. This feature prevents anyone from changing any of the machine’s settings during a wash cycle. This comes in very handy for homes with little kids.
Samsung Washing Machine Is Flashing ND
If your Samsung washing machine is flashing the ND error code, it means that the washer is not draining. Here are the different things that can cause this issue…
Samsung Washing Machine Is Flashing 4C
If your Samsung washing machine is flashing a 4C (or 4E) error code, it means that the washing machine isn’t getting enough water. Here’s what to do to fix this issue…
Samsung Washing Machine Is Flashing 5E
If your Samsung washing machine is flashing the error code 5E (often read as SE), it means that there is an issue with the drainage system. Here’s what to do if your Samsung washing machine is not draining…
Why does my Samsung washer have a loop?
If the machine works fine but gets into a loop in the rinse cycle, it could be a sign of some issue with the cold water faucet. If it is clogged, the washer will not get enough water to complete the rinse process, hence the loop.
Why does my Samsung washer have an out of balance feature?
The “out of balance protection” feature in some Samsung washers leads to more water being added during a spin cycle if it suspects a small load. This is to protect the machine from damage, but it will lead to excess water in the end. To avoid this, redistribute the clothes to ensure a better balance in the washer.
Why is my washer stuck in the rinse cycle?
If it is stuck in the rinse cycle, it could be that the timer is failing to communicate with the rest of the control unit. Replacing the timer will, therefore, correct this problem.
Why is my washer not rinsing?
Check for Electrical Issues. If there is faulty wiring somewhere in your washer, it could be the cause of the rinse loop. Such wiring problems can prevent the timer from working. It could also lead to an internal power cut when the washer is at the rinse stage. Such problems are best left to professionals.
What to do if Samsung washer isn't filling with water?
If your Samsung washer isn’t filling with enough water, the first port of call should be the water inlet valve. If you don’t find any problems with the valve, there are other things you can do. They include the following:
What to do if Samsung washer won't work?
If your Samsung washer won’t work, the first thing you should do is to find the right troubleshooting techniques that can correct the problem. In some cases, pressing the right buttons on the washer is enough. For more problems that need extensive repair, you’ll need to contact the service center.
How to calibrate Samsung washer?
The buttons that will bring up the calibration mode will vary from one model to the other, but in the average Samsung washer, the process will involve the following: 1 Press and hold “Temp.” and “Delay End” simultaneously for three seconds. 2 Wait for “Cb” to appear on the display. 3 Press “Start” or “Pause” to get the tub to rotate back and forth for 1-3 minutes. 4 Watch for “En” “End” or 0 on the display. 5 Turn off the machine.