Receiving Helpdesk

why is my lawn mower string stuck

by Miss Alexandria King Published 3 years ago Updated 2 years ago

What Causes The Lawn Mower Pull Cord To Get Stuck?

  • Debris. If the mower is not frequently checked and cleaned, it doesn’t take long for debris to build up in the blade.
  • Automatic Break. A common problem with the pull cord is the automatic break. ...
  • Recoil Starter. This particular problem sounds a lot more intimidating than it really is. ...

Full Answer

Why is my lawnmower pull cord stuck behind the starter?

Sometimes the mower starter clutch becomes seized because the ball bearing inside the clutch becomes rusted. Fixing this issue helps you to pull the starter cord freely. These are the reasons that are actually working behind the lawnmower pull cord stuck.

Why won’t my lawnmower start?

And due to a stuck pull cord, it doesn’t allow the lawnmower to start. Recently I faced this problem and fixed this at home. You know when you pull the cord, it rotates a hub that connects the crankshaft and spins the blades.

Why does the pull string lock up on a push lawnmower?

When a push lawnmower's pull string, or starter rope, locks up, it could mean the engine has a problem, but that usually isn't the case when oil is added to the engine regularly.

Why is my lawn mower hard to pull without a blade?

A tangle of rope or a broken spring could be the problem. The rope is very difficult to pull if a lawnmower blade is missing. The flyweight of the blade is what carries the engine through the compression stroke. Don’t run a mower with no blade. How can I make my lawn mower pull easier to start?

What causes lawn mower pull cord stuck?

Grass and Debris Is in the Way The blade is connected to the starter coil, so if the blade is unable to move, your pull cord will be stalled as well. If your pull cord moves slightly, it's likely that there are grass and debris that needs to be removed from the housing on the top of the motor.

What do you do when your cord gets stuck?

0:051:41How to fix a pull cord stuck after tipping mower - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst put a rag down to catch the oil pull off the spark plug wire. And move it out of the way thenMoreFirst put a rag down to catch the oil pull off the spark plug wire. And move it out of the way then remove the spark plug. Pull the starter rope several times to clear oil out of the cylinder.

How do you fix a lawn mower cord that won't retract?

0:412:58HOW-TO Tighten A Limp Starter Rope That Won't Retract On A Small EngineYouTubeStart of suggested clipEnd of suggested clipI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would goMoreI'm just going to turn counterclockwise. One turn on this one if the rope was out further I would go two turns counterclockwise. And with this recoil here one turn counterclockwise fix.

What causes a push mower to lock up?

Your lawn mower's piston can seize if the mower stands for a long time in wet conditions or if you forget to put oil in the crankcase. You may be able to free the piston by removing the spark plug and manually rocking the blade.

How do you loosen a lawn mower string?

If the lawn mower start string being stuck is an ongoing problem, you should spray a small amount of WD-40 as needed, whether that's every time you use it or a few times each year.

How do you fix a pull start string?

0:352:51How-To: Fix a Broken Recoil Rope - YouTubeYouTubeStart of suggested clipEnd of suggested clipWe've applied a double knot on the other end of the rope. We've done the same thing we drew the ropeMoreWe've applied a double knot on the other end of the rope. We've done the same thing we drew the rope through the handle. And apply - double knot at the end.

How do you fix a pull cord spring?

0:096:40How to fix a pull starter recoil spring and replace a stuck or limp pull cordYouTubeStart of suggested clipEnd of suggested clipJust kind of have to work it with your pair of pliers the most important thing is. This is whereMoreJust kind of have to work it with your pair of pliers the most important thing is. This is where it's gonna go once it's in there it's gonna go like this. Okay go in there like that you know catch it.

How do you lubricate pull start?

3:335:41How To Lubricate A Sticky Starter On A Chain Saw or Weed EaterYouTubeStart of suggested clipEnd of suggested clipRight I usually go on the top when I put a couple good blasts in the in the top in the hole that'sMoreRight I usually go on the top when I put a couple good blasts in the in the top in the hole that's closest to the top blast. It in there like that.

How do you start a lawn mower with a broken string?

Depending on where the rope broke, you might have some rope left on the coil wheel. You can feed the old rope back through its hole and retie the pull handle if you have enough rope to pull start the mower. Next, replace the housing and then screw it back in place.

How do you know if your lawnmower is seized?

How to tell if a riding lawnmower engine is seized:It sounds rough.Hard to start the engine.The blades are stuck.The piston and cylinders won't move.The oil will be deficient.The fuel quality will have deteriorated.How to tell if a riding lawnmower engine is seized?https://www.gardentoolexpert.com › how-to-tell-if-a-ridin...https://www.gardentoolexpert.com › how-to-tell-if-a-ridin...Search for: How do you know if your lawnmower is seized?

How do you fix a seized lawn mower?

Step 1: Tip the Lawn Mower. Set the lawn mower on a level surface and tip it so the spark plug is facing up.Step 2: Remove the Spark Plug. ... Step 3: Spray PB Blaster Into the Spark Plug Cavity. ... Step 4: Unstick the Engine by Turning the Blade. ... Step 5: Add Engine Oil.Step 6: Replace the Spark Plug.Step 7: Start the Engine.How to Repair a Seized Lawn Mower Engine - Hunkerhttps://www.hunker.com › how-to-repair-a-seized-lawnm...https://www.hunker.com › how-to-repair-a-seized-lawnm...Search for: How do you fix a seized lawn mower?

What causes a pull cord to lock up?

The starter cord can get stuck if oil gets trapped in the chamber of the engine. The spark plug needs to be removed so you can give the cord a tug.

Why is my lawnmower pull start stuck?

When a push lawnmower’s pull string, or starter rope, locks up, it’s possible that the engine has a problem, but that usually isn’t the case when oil is added to the engine regularly. There is a problem with the recoil starter. You should mow after a few minutes if the engine has stopped.

Why is it hard to pull the cord on my lawn mower?

A tangle of rope or a broken spring could be the problem. The rope is very difficult to pull if a lawnmower blade is missing. The flyweight of the blade is what carries the engine through the compression stroke. Don’t run a mower with no blade.

How can I make my lawn mower pull easier to start?

If you remove the spark plug from your lawnmower, the muscles involved will be regenerated. This will reduce the resistance of the engine and allow you to pull the cord as an exercise that will strengthen your muscles.

Why won't my mower pull the starter cord?

The firing of the spark plug initiates the ignition. Hence, your engine starts over. If there are obstructions within the mower blades or the engine’s starter hub , you won’t pull the starter cord.

Why does my lawn mower blade keep spinning?

This condition prevents It from spinning due to obstruction between the blade and the mower deck. As said before, the pull cord is responsible for spinning the mower blades that eventually start the engine.

How do I fix a lawn mower pull cord?

How to fix a lawnmower pull cord that is stuck, step by step: Step 1: To start, inspect your blade for any stuck strands of grass or debris. Remove them as they cause the pull cord to get stuck. Step 2: Open the blower housing and inspect the recoil starter. If it appears damaged, you need to replace it.

Why is my pull cord stuck?

For one, the development of grass or debris needs to be removed to allow the pull cord to work again . You might also have an issue with your recoil starter, which may be broken.

How to replace a recoil starter?

Replacing the recoil starter: Replacing a recoil starter is seldom difficult. To perform the replacement, remove the recoil starter guard. Next, use a screwdriver to remove the tabs connecting it to the blower housing. Remove the old starter and add the identical one to its place in the tabs.

Where is the recoil starter located?

The recoil starter is situated under the blower housing. Before doing anything, ensure that the spark plug wire is removed. Also, release the starter cable or the pull cord from the mower handle. Now, remove the screws securing the blower housing.

How to get oil out of spark plug?

Place a dry cloth near the spark plug hole since we will spray the oil out of the engine. Try to start your engine by pulling the rope several times. You shall notice oil being thrown out of the spark plug hole. When the oil has stopped spraying out, reattach the spark plug and connect the wire back to the plug.

What happens when you give a mower a hard pull?

Or worse, the mower fires up for a minute and the cord is whipped back, you hear some funky grinding noise, and the mower dies.

How to recoil a spring?

How to Recoil the Spring 1 Bend the tabs up so the coil can be removed from the housing. 2 With the coil in hand, pull the end until the coil is compact and even; a nice spool. 3 Now place the end holding tab into the housing and lay the rest of the coil in the housing carefully. 4 Hang onto the coil so it won't uncoil before you're ready. 5 While holding the spring with a small finger, place the coil on top of the spring inside the housing and carefully release the spring. The clutch will hold it in place while you bend the tabs down. 6 Place the starter assembly back onto the clutch and put the screws back in. 7 Guide the string back through the pull start hole in the housing and tie it back onto the handle.

Can you fix a spring if it is sprung?

After the rust is cleaned out and put back in place with the ball bearings it's time to fix the spring if it is sprung. Often times the spring is sprung from the starter seizing up. They're not too difficult to recoil.

What does it mean when a motor cord is stuck?

If the cord is moving sluggishly or slowly, this indicates debris or blockage in the top housing of the motor. If the cord is completely stuck, then there might be damage to the cord, or it is caught by a component of the housing. If this happens, then you should unscrew the screw that is on the top of the motor housing.

How does a lawn mower work?

The mower cord is connected to a hub, and this hub spins when you pull the cord. In turn, this spins the blades of the lawnmower, and the crankshaft as well. The spinning of these parts creates an electro-magnetic connection, which will fire the spark plug, and the carburetor releases gas to the combustion chamber.

How to replace a spring on a Honda Civic?

For you to replace the spring mechanism, you will need to separate the starter cover from the hub by removing the cord itself. After you replace the spring, you can then wind the hub, insert the cord into the holes on the cover and hub, securely form a knot, and allow the hub to slowly rewind before placing the cover.

What happens when you pull a gas cord?

Every time you pull the cord, a recoil spring within the motor housing rewinds it back into its original position. When the system adjusts everything correctly, the cord should not have any slow or remain in a stuck position.

Can you panic when you have a stuck cord?

In case you ever encounter issues with stuck cords, you do not need to panic. It is a problem you can solve easily, especially when you know what the problem is. Hopefully these tips will help you to solve the problem as quickly as possible.

How does a Pull Cord Function?

The cord on your lawnmower connects to a hub that in turn spins when you pull the pull cord. This will spin the lawnmower’s blades together with the crankshaft.

How to Fix a Lawn mower Pull Cord that is Stuck – The Possible Solutions

Solution 1: Initially, I would check out the automatic brake on my lawnmower. Some manufacturers have their mowers automatically stop the engine for safety purposes.

Conclusion

If this is your first time dealing with a stuck pull cord, do not worry and do not panic. This is an entirely normal problem that is quite commonplace yet very easily resolved.

What happens if your lawnmower pull cord is stuck?

If the pull cord on your lawnmower is stuck, you're not going to be cutting the grass with that mower until you fix it. Although it might seem like a big problem, it usually isn't.

How does a lawn mower work when pulling a cord?

When you pull your lawnmower cord, it spins a hub that is connected to the crankshaft, which spins the lawnmower blade. As the crankshaft spins , an electro-magnetic connection fires the spark plug at the same time that the carburetor injects gas into the combustion chamber . Once the gas ignites, the engine starts operating.

How to reset a starter spring?

After replacing the spring, wind the hub, feed the cord through the holes in the hub and cover, tie a knot and let the hub rewind slowly before replacing the starter.

Why does my lawn mower pull string lock up?

When a push lawnmower's pull string, or starter rope, locks up, it could mean the engine has a problem, but that usually isn't the case when oil is added to the engine regularly. On a rotary mower, the starting mechanism is connected to the cutting blade, and a buildup of debris on the blade can make starting the mower difficult. The problem also could be with the recoil starter. Unless the engine has seized, you should be mowing after a few minutes.

What causes a lawn mower to get stuck in the starter rope?

The starter includes a spring-loaded hub that spins the engine crankshaft and the lawnmower blade when you pull the starter rope. The spring can bind or even break, and it's possible for the rope to cross over itself when it rewinds and get stuck.

How to start a lawn mower when the underside is clear?

After the mower's underside is clear, pull the starter rope while depressing the brake lever on the handle if a brake lever is present. If you forget to depress the brake lever while pulling the starter rope, the starter won't turn and the engine won't start.

What to do if your mower runs out of oil?

If the mower runs out of oil while it's operating, major repairs are the usual result, but if it happens when the engine is cold and you're trying to start it, adding more oil should free the piston. Check the oil dipstick. If it shows that the crankcase is empty, add the recommended oil for your mower. Put on leather work gloves, and gently push ...

How to wind a rope after replacing spring?

After replacing the spring - if that task is necessary - wind the hub until the hole in the center lines up with the hole in the housing. Holding it steady with a screwdriver, feed the rope through both holes, tie a knot and allow the hub to unwind slowly to wind the rope.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9