Our Hayward system shuts the chlorinator off automatically when the water flow is too low. I can usually hear when the system is struggling for water as the pump gets louder and makes a recognizable sound. Ensure all proper valves are open and weren’t closed, thereby restricting water flow. Check the skimmer for blockages.
What should I do when working on my Hayward chlorinator?
When working on the chlorinator you will want to make sure that your swimming pool filter system is shut off. You will also want to unplug t he pump cord if possible to prevent the swimming pool timer from kicking on the pool pump while you are working on rebuilding your Hayward Chlorinator.
What is a clog in a Hayward chlorinator?
Clogs can also occur in the control valve when you vacuum the pool, and airlocks can develop inside the cartridge. Clogs and airlocks restrict water flow, and the pool chlorine levels will fall. Hayward offers four chlorinator models--two for in-ground pools and two for above-ground pools.
Why is my chlorinator not fitting properly?
My Chlorinator Lid is Tight, Leaking, or Won’t Fit Properly Whenever you have a leak, the first places you want to check are the gaskets and O-rings. The O-ring on the inside of the chlorinator can become brittle over time.
Does a Hayward chlorinator have a check valve?
All models have a check valve to ensure that water flows only one way. Each Hayward chlorinator has a removable lid that allows you to drop in a slow-release Trichlor chlorine tablet. It also has a flow-control valve that allows you to adjust the flow of water.
Why is my chlorinator not working?
The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.
How do you unclog a chlorinator?
0:091:01How to Unclog a Tablet Chlorinator - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can also escort a water hose down the chlorinator to help clear out the blockage the tabs.MoreYou can also escort a water hose down the chlorinator to help clear out the blockage the tabs.
How do I know if my chlorinator is clogged?
3:314:13Pool Chlorinator Clog FIX! - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd what you should hear once you un do it when you turn off the pump and you actually take the lidMoreAnd what you should hear once you un do it when you turn off the pump and you actually take the lid off you should hear a suction sound so i'm gonna let you listen to that. Here.
How do I reset my chlorinator?
To reset, move the switch to 'Off' and then back to 'Auto'. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to 'Super Chlorinate' and back to 'Auto'. It takes about 30 seconds for the unit to settle back on the default reading.
How do you clean a Hayward automatic chlorinator?
0:001:37Servicing the Hayward Chlorinator - YouTubeYouTubeStart of suggested clipEnd of suggested clipUsing a slot screwdriver gently pry open the cap from the body and replace the o-ring. You you canMoreUsing a slot screwdriver gently pry open the cap from the body and replace the o-ring. You you can now reassemble the cap and cover make sure that you have the slip washer between the cap.
How do you open a stuck Hayward chlorinator?
Try to get some air into it by opening up the air pressure relief valve atop your filter, or by draining your filter. Then whack it with some moderate force with a screwdriver. Also, if it has a handle on top, you could use a long bar/screwdriver/whatever to create more leverage.
Why is my salt water pool not generating chlorine?
Salinity. Chlorine generators need salt to produce chlorine and can't do so if the amount of salt in the water is too low. The desired salinity level in a saltwater pool is between 2,500 and 3,500 ppm. Get a salt-testing kit from a pool supplier and check to make sure that the levels are within this range.
How do I reset my Hayward salt cell?
Reset AquaRite Salt Chlorination Inspect Cell Light If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.
What should my Hayward chlorinator be set at?
The safe operating range of pH is between 7.2 and 7.8 PPM.
How do I know if my salt water chlorinator is working?
1:252:22Tip 3 - How to check if your salt cell is working - YouTubeYouTubeStart of suggested clipEnd of suggested clipWhat we're doing here and we turn it on is we're looking for bubbles or a fizzing. Effect. Once weMoreWhat we're doing here and we turn it on is we're looking for bubbles or a fizzing. Effect. Once we see the bubbles. And the fizzing. We know that it's actually working.
How do I know if my Hayward salt cell is working?
The easiest way to ascertain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights. Ensure there is enough salt in the pool. On the chlorinator box there should be a light or dial that indicates it is working.
How do I reset my Hayward Aqua Plus?
You must reset the system by entering the 'Diagnostic Menu' and then hitting the right arrow key once and then pushing the plus key once. This should reset the light and message.
How to replace a Hayward CL110 chlorine line?
To replace the lines on the Hayward CL110 Chlorinator you will need to loosen the nuts at the end of each line. Turning them counter clockwise will loose these nuts, be sure to do it carefully or the chlorine feeder line nuts could break or strip out. Once the nuts are loose you can remove both the feed and return lines. The Hayward re-build kit for the Chlorinator should have new nuts and lines in the pack.
What is a Hayward CL110 chlorine feeder?
The Hayward CL110 Chlorinator is a bit different from the CL220 model. This model uses flexible black chlorine feeder hoses to connect the tank to the filter system. From time to time these lines will become brittle and need to be replaced. You can buy replacement Hayward Chlorine feeder lines online or from a local swimming pool supply store.
How to work Hayward CL220?
In order for the Hayward CL220 or the CL110 to work right you must have the chlorinator set and installed with the correct direction of flow. On the side of the chlorine feeder you will see an arrow that says, “flow”. This arrow needs to be pointed towards the return side of the swimming pool plumbing.
What is the dial setting on a pool chlorinator?
The dial setting ranges from 1 to 10. You can use this dial on the side of the chlorinator to control the amount of chlorine that goes back into your swimming pool. To increase the level of the chlorine into the pool you would want to turn the dial up towards the 10 setting.
Can you run water through a chlorinator?
Try to always run water through the chlorinator by turning the pool on first, this was NOT a typo that was said twice, Chlorine gas can be very dangerous, be careful anytime you work with any type of swimming pool chlorine or tablets.
Can you run a CL110 above ground pool?
Before working on either the in ground model which is the CL220 or the above ground swimming pool model which is the CL110 you will always want to make sure you can run the pool water though the chlorinator for a few minutes.
What to do if your CYA is too high?
Normally the best course of action is keeping the CYA level down to a manageable level, or if it's already too high, replace enough water to get it to a manageable level and then SLAM the pool.
Does rinse water go backwards?
Smy answered you, so I'll just elaborate and say that rinse runs water backward through the filter media so there's the potential that you could clog the media running enough water through it to empty the pool. waste runs water directly from the inlet of the filter to the waste port.
Can you replace cya with water?
Unfortunately there's no proven way except water replace ment. The problem with using tablets is that the cya gets high really fast in a lot of cases, and it becomes almost impossible to keep raising the fc to levels required to prevent algae blooms.
How to switch cell type to super chlorinate?
Switch your cell type by cycling the main switch from AUTO to SUPER CHLORINATE and then back to AUTO.
What is the salt level of a chlorine generator?
Your salt level is between 2500-2600 parts per million (ppm). Your chlorine generator is still producing chlorine at the moment, which is a good thing. This is more of an indicator light than anything else. The salt level is 2300 ppm or less and no chlorine is generating.
How to fix 500 hour countdown timer?
The 500 operation hour countdown timer expires. To fix the problem, manually reset the Inspect Cell LED.
Why Is My Salt Chlorinator Cell Not Working?
The chlorinator system that we got when we bought our house with a 3 year old pool was a first generation Lectrinator salt system. That company went bankrupt in early 2020 but we had already replaced the entire salt system with a more modern and automated Hayward AquaRite system in 2010 after the Lectrinator cell died twice and needed to be replaced sooner than I’d hoped.
How long do chlorinators last?
A good quality, well-maintained chlorinator cell may last 3-5 years on average but will eventually need to be replaced. Why do chlorinators fail, how do you know when they’ve failed and what can you do to extend their life?
What is a chlorinator cell?
The chlorinator cell is an integral part of the salt water pool system that electrically converts salt to chlorine. Major manufacturers of salt water pool systems include Hayward, Pentair, Jandy and CircuPool.
Why put Hayward Turbo Cell in place?
I was told to always put our Hayward Turbo Cell in place so that the indented side is facing down so there is always a pool of water at the bottom of the cell in the off chance the flow slows and the sensor doesn’t react. That way there is always some water in the cell and it won’t get damaged.
When to add salt to pool?
If it’s really low, you might have a lack of salt that requires more salt added to the pool. I typically add a large bag of salt in the spring when opening the pool and a smaller bag midway through the summer. I generally take a water sample once per month to the pool company and they tell me when it’s time to add salt.
Does Hayward self clean?
Our Hayward system has a self-cleaning cell feature that I use so I haven’t had to manually clean the cell before. I generally only take the cell out at the end of the season for storage over the winter and take a look at the metal plates to make sure they’re clean. Your system manufacturer might have a similar feature or you may have to manually clean the cell from time to time as per their instructions.
Can chlorine be used to damage cells?
Avoid running large amounts of chemical chlorine (liquid, crystal) through the cell as it can damage it over time.
How to clear a chlorinator valve?
To clear the valve, first, remove the chlorinator lid. Using tongs, remove the chlorine tablets from the canister. Next, using tongs, remove any sludge or debris at the bottom of the chlorinator. Finally, remove the screen and hose it down with water.
How to get air out of a chlorinator?
First, turn your pump off and remove the chlorinator lid. Low water in the canister indicates the presence of air. Next, restart the pump while the lid is off and allow water to fill the canister. As the water rises, it will push the air out of the system. Once the water fills the chlorinator, you can reinstall your lid.
What is an offline chlorinator?
Offline chlorinators are ideal for pool owners installing a chlorinator into an existing pool line. You install them “off” of the existing plumbing line and attach thin tubes into the line.
What are the two types of chlorinators in a pool?
Before we begin, let’s make sure you know which type of chlorinator you have. There are two different types of chlorinators: inline and offline . The main difference between the two types of chlorinators is how you install it.
What happens if you reverse a chlorine hose?
However, if you reverse the hoses, the injection process that dissolves the chlorine will not function. Look for directional arrows on the hoses showing the correct installation direction.
What to check for when a chlorinator leaks?
Whenever you have a leak, the first places you want to check are the gaskets and O-rings. The O-ring on the inside of the chlorinator can become brittle over time.
Do pool chlorinators dissolve?
Tablets Are Not Dissolving. One of the most common swimming pool chlorinator issues we encounter is the tablets not dissolving. Or, in some cases, they aren’t dissolving as quickly as you think they should. However, pool owners can still come across other issues that contribute to undissolved chlorine tablets.
How to fix chlorinator that is not dissolving?
– If an Off-Line chlorinator, check the injection fittings where the hoses attach. Clean with water and a paperclip.
How long does chlorine last in a pool?
Most will hold around 9 lbs, or enough chlorine to last 2 weeks for the average size swimming pool.
What is the best way to use chlorine tablets?
Using a erosion feeder by Hayward or Pentair is the best way to use chlorine tablets or sticks. Floaters in the pool are less desirable for many reasons, but better than putting tablets in the skimmer basket (please don’t do this!).
Can you use a chlorinator offline?
In many cases, there is simply not a suitable location for an in-line chlorinator to be installed. Perhaps there is not enough of a straight run of PVC (you need about a foot), or no area that would allow for easy access to the chlorinator to fill with chlorine tablets. In these cases, an offline chlorinator may be your best bet.
