Why Washing Machine Drain Pump Keeps Running?
- Damaged Control Board. What it is: Most household appliances these days rely on what’s known as a control board. ...
- Faulty Drain Pump. ...
- Defective Water Level Switch. ...
- Broken Water Inlet Valve. ...
- Drain Hose Is Placed Incorrectly Inside the Standpipe. ...
- Final Thoughts. ...
Why is my washing machine not spinning or draining properly?
| What You Need to Know
- Check Your Machine’s Power Supply. Perhaps one of the easiest answers to the question, “Why is my washer not draining or spinning?” is in its power source.
- Reset Your Machine. If your machine has this function, try performing a master reset on it. ...
- Check the Machine’s Position on the Floor. ...
- Rebalance the Washer’s Load. ...
- Inspect the Lid Switch. ...
What causes a washing machine to not spin or drain?
- The washing machine sounds different than usual.
- The laundry is still damp or even wet when it comes out of the machine.
- There is still water in the drum at the end of the wash cycle.
How to fix a washing machine that won't drain?
How to Fix a Washing Machine That Won’t Drain
- Remove the Front Panel Screws. Start by unplugging the machine and emptying the water. ...
- Open Up the Washer. Before you do any work on the inside of the washing machine, make sure that the machine is completely unplugged.
- Look for the Clog and Pull It Out. ...
- If There's No Clog, Check the Pump and Remove It
Why is my Maytag washing machine not draining?
- Delicate or handwash cycle selected
- Extra Low, Low or No Spin option selected
- Washing one bulky item
- Excessive suds
- Drain hose kinked or drain clogged
- Drain hose more than 96” above the floor
- Outlet voltage low
Why does my washing machine keep draining?
If your washing machine drains while filling, check and make sure that the washer’s drain hose isn’t too far into the standpipe as there needs to b...
What causes a washing machine drain to overflow?
The most common reason for overflowing is a blockage in the drain hose or standpipe.
Can I put Drano down my washing machine drain?
Yes. Drano or any drain cleaner can be used to unclog your washing machine drain, but make sure you run your washer without a load of laundry befor...
Washing Machine Drain Hose Is Not Properly Positioned
The first cause of washing machine overflow is that the drain hose must be appropriately attached to ensure proper drainage.
Washing Machine Drain Filter Is Clogged
The second cause of washing machine overflow is clogged filter screens in the drain hose, often caused by fine clothing particles getting caught during the wash cycle.
Washing Machine Drain Connection Has Been Improperly Installed
If the piping isn’t connected at both ends, this will make for incomplete drainage and could lead to an overflow situation.
Washing Machine Draining Slowly
If your washing machine has been installed correctly and the filter screens are clean, there is still a chance that it can overflow.
Washing Machine Not Level
Washing machines work by pushing or drawing water out of the drum and up into the drain hose, which should be attached to a pump at the height of your washing machine floor connections.
Washing Machine Drain Hose Is Overflowing
If your washing machine drain hose is where the problem lies, you’ll notice that it already has water overflowing from it.
Washing Machine Overflowing at The Spin Cycle
If it’s happening at the spin cycle, this means that your washing machine is overloaded with clothing. Washing machines are designed to pump out excess water after each cycle has finished; if they can’t do this in an average amount of time, they will overflow onto the floor.
Why does my washing machine drain overflow?
If your washing machine drain overflows by the wall where the discharge hose goes in, the problem is likely caused by a buildup of residue and debris which has clogged the drainpipe in the wall behind your washing machine.
How to fix a clogged washing machine drain?
1. Create Space. The first thing that you will want to do to fix the problem of a washing machine drainage clog is to move the washing machine away from the wall. The drain behind the wall is where the discharge water goes into and when that drain is clogged water backs up. To access the drain, you will need to create space to work by moving ...
How to unblock a clogged drain pipe?
The first thing that you can try is boiling hot water. Remove the waste pipe and carefully pour boiling water through the pipe. While in many cases hot water can solve any drain problems that you have, some blockages can prove more difficult.
How to avoid water spills in washing machine?
3. Unclogging Methods. There are a few different methods that may work to unclog the drain behind your washing machine.
What is the best way to clear a drain pipe behind a washing machine?
An auger, also known as a snake, is the most common method used as it is a mechanical device that can physically remove any debris that is blocking the drainage. There are several different types of augurs that you can use to clear a drainpipe behind a washing machine.
Why does my washing machine back up into my shower?
If your washing machine is backing up into your shower the problem is mostly related to a clog in the drainage system . When a washing machine is tied to the same drainage pipe as a shower, the shower serves as the path of least resistance for any water stopped by a blockage in the drainage system.
Can hot water flush a drain?
On the other hand, if the blockage is caused by soap and lint buildup, very hot water may very well flush out the drain. 4. Reinsert Washing Machine Hose to Drain. It’s always a good idea to test the drain to make sure ...
Why does my Samsung washing machine keep draining?
Here are the reasons why your Samsung washing machine keeps draining: 1. Drain Hose Is Inserted Too Far Down Your Home Drain. Inserting your drain hose too far down your home drain can cause drainage problems. In order to avoid this issue ensure that the hose hasn’t been inserted more than 6 inches into your home drain.
Why does my washing machine overfill with water?
This required pressure varies between washing machines. If the machine doesn’t get the right amount of pressure, the water inlet valve won’t close completely. As a result, the machine overfilled with water.
What does a defective control board do on a Samsung washing machine?
Defective Control Board. The control board does exactly what the name implies. It controls the machine’s functions and initiates wash cycles. If your Samsung washing machine keeps filling and draining , this may be a sign that the control board is defective.
What is the best way to test a washing machine?
1. Water Inlet Valve. This valve controls the water coming into the washing machine. If the valve is defective or broken, it won’t close properly. This means water will still be running. You can test this by unplugging your machine while it’s in a fill cycle.
How high should a drain hose be?
Also ensure that the drain hose is suspended at a minimum height of 18 inches. However, it must not exceed 96 inches. If playback doesn't begin shortly, try restarting your device.
Why does my washer keep filling?
If your washer continues to fill during a drain cycle, the water inlet valve could be at fault. To verify that the valve is at fault, unplug the washer when the symptom occurs. If the washer continues to fill, then the inlet valve is defective. If the washer stops filling, then the problem is related to the electrical circuit ...
What is the water inlet valve on a washing machine?
The water inlet valve on your washing machine is used to fill the tub with cold, warm or hot water for the wash and rinse cycles. The valve is operated by electric solenoids that are controlled by the timer or electronic control board and the water level control/water level selector switch or pressure switch.
Where is the water inlet switch on a washer?
On washers that use an electronic control, this switch may be located at the sump area below the tub. As the water fills in the tub it will compress the air in the tube and push against a diaphragm inside the switch. The switch will control the water inlet valve and turn the valve off at the correct water level.
Why won't my washing machine drain?
The number one cause for a machine that won’t drain or spin is because of a user error. Often people select the wrong type of cycle for the laundry they are doing. Delicate and hand wash cycles are designed to spin more slowly, and if these modes are selected for the wrong fabrics, the machine won’t drain properly.
Why does my washing machine shut off?
If the system that is powering your washing machine has any sort of blips or inconsistencies in power, your machine may shut off randomly. This will cause the machine to quit its cycle altogether. The machine probably won’t restart on its own, and it may not even drain.
Why does my Whirlpool washer keep going through the wash cycle?
If your whirlpool washer completes an entire wash cycle, and then automatically starts again, the most common reason is because it is stuck in a test mode . One way to test if this is the issue is to unplug the washer for ten seconds, then plug it back in and run the cleaning cycle. If the washing machine tries to repeat the cycle again, ...
How long does a Whirlpool washer spin?
The washer then continues spinning for a long time, sometimes up to an hour.
What does a washer sensor do?
The job of the sensor is to detect when the inner tub and spinning hub are aligned. Once the inner tub falls into place, the sensor will signify the rest of the cycle to start. When your washer is stuck on the sensing mode, the sensor is detecting an issue somewhere in the machine.
Why isn't my Whirlpool washer working?
Some of the most likely reasons why your Whirlpool washer isn’t working include uneven loads, hot water issues, and the washer’s timer being stuck. It could also be caused by a blocked drain or a faulty fuse in your home.
Why does my Whirlpool washer stop spinning?
The most common reasons why your Whirlpool washer may stop at the beginning, or in the middle of, the spin cycle, comes down to faulty switches. There are two main switches which need to be engaged for your washer to run. They are similar, but different.
Why does my washing machine drain pump keep running?
In that case, it could result from a damaged control board, a faulty drain pump, or a defective water level switch.
Why does my washing machine not measure water levels?
Why it fails: If the water level switch in your washing machine is defective or faulty, it won’t be able to measure the water levels accurately. The switch may mistakenly think that the washing machine is overflowing with water, and so it’ll activate the drain pump to empty itself out.
What is a washing machine drain hose?
What it is: All washing machines have a drain hose connected to its back or side panel. When the washer begins its drain cycle, the drain pump will turn on and send water from the washer out through that drain hose. Quite often, that drain hose leads out of the washer and into a standpipe.
What is a faulty drain pump?
Faulty Drain Pump. What it is: To clean a load of laundry, a washing machine needs to go through several stages or ‘cycles’. All of it begins with the washing filling the drum with water. The drum will then spin around to agitate all of the dirt to come out of the clothes inside.
How to find water level switch on washer?
The best way to locate the switch on your washer is to refer to the user manual. Still, you can usually identify the water level switch very quickly.
What is the function of a control board on a washing machine?
Your washing machine also has a control board, and its job is to regulate all of your washer’s different functions. First, you’ll input all of the settings you want to use to wash your load of laundry. That includes temperature, time, spin cycles, and so on.
Can a washing machine control board get damaged?
In that case, the washing machine will start to behave unusually. There are many ways a control board can get damaged. For starters, the manufacturer that put it together could have overlooked some mistakes and given you an inferior control board, to begin with.
1. Clogged Drain Hose
If your washing machine isn’t draining, the most likely culprit is a blocked drain hose. The drain hose is the rubber tube located behind your washing machine. When lint or other debris accumulates in this tube, it can hinder water flow and affect the performance of your washer.
2. Improper Drain Height
Washers need to be installed at a certain height from the floor. If you’re too high, your washer may not be able to drain water well. Before you install your brand-new washing machine, check the instruction manual for details on drainpipe height and how it can impact your drainage rate.
3. Poor Load Distribution
An unevenly distributed load can throw off your washer’s balance, causing it to vibrate when it spins, which prevents the clothes from being cleaned properly. Unbalanced loads can also damage components of the machine, resulting in costly repairs.
4. Clogged Drain Pump Filter
The drain pump in all washing machines is designed to evacuate the water from the tub after cycles of washing and rinsing. However, if during one of these draining cycles you hear that the pump appears to be running but water is either going down slow or not at all, then this usually indicates a problem with this pump.
5. Check Lid Switch
The most important part of any washing machine safety system is the lid switch. This system prevents damage or injury by stopping the machine immediately if the lid is open.
6. Faulty Drain Pump
If you notice water still sitting in the washer tub after washing a load of laundry, check to see if there are any obstructions blocking the drain line or if the pump itself has failed. A failed pump will likely have an audible issue, such as a grinding or whirring sound that may have started slowly and steadily increased over time.
7. Worn Out Drive Belt
If the water isn’t draining during a wash or rinse cycle, it could be because of a few different reasons. If the problem isn’t the drain pump, it may be the drive belt. Located at the bottom of the machine, this belt helps operate the pump. If it’s torn or damaged, the pump will not be able to work properly.
