What does loc mean on my Maytag washer? A lock icon appears on the front of the washer's control panel to indicate the lid is locked and also displays the current progress of the cleaning cycle, depending on the model of your Maytag washer. Once paused, the lid automatically unlocks to allow changes to the current load.
Why does my Maytag front load washer say Loc?
Why does my Maytag washer say Loc? LoC or LC - Front Load Washer. This error code does not mean "Door Locked". The door will open when the control is locked, but the washer will not start, due to control being locked.
Why is my Maytag washer not turning on?
If a Maytag sensor light is on, but you cannot get any of the commands to engage or start, this could also be a problem with the unit’s shift actuator. This is primarily caused by the shift actuator not being able to engage the drive shaft to respond to the washing machine’s commands; it could also be caused by wiring that has failed.
Can fix appliances CA help with Maytag washer error codes?
Luckily, Fix Appliances CA has the knowledge and expertise of qualified appliance technicians to handle any Maytag washer error code — for Maytag washing machine troubleshooting check the code explanations below.
How do I take the lock off my Maytag washer?
In this regard, how do I take the lock off my Maytag washer? To unlock the controls, press and hold the CYCLE END SIGNAL for 3 deliberate seconds or until the control lock light goes out. If the control locked light will not turn off, I recommend unplugging the washer for 5 minutes. How do you reset the key on a Maytag commercial washer?
How do I clear the LOC on my Maytag washer?
How do I fix my washing machine Loc?
How do I unlock my Maytag washer?
Why does my washer keep saying Loc?
How do I turn off the LOC on my Whirlpool washer?
Touch and hold 3 seconds again to de-activate the Control Lock.Jun 12, 2020
Is there a reset button on Maytag washer?
How do you bypass a washing machine lock?
How to Fix Maytag Machine drn Error Code
Standpipe drain system: The drain pipe end must be at least 36 inches and no more than 96 inches above the floor. Check the installation point and...
How to Fix Maytag Machine F# E# or F## Error Codes
To reset the code of the motherboard hold the START/PAUSE button once to clear the code, then press the START/PAUSE button again to reset the washer.
How to Fix Maytag Machine HC Error Code
This is a fairly easy fix that requires switching the hose inlet hoses. The error message shows up when the hoses for hot and cold water are instal...
How to Fix Maytag Machine LdL Error Code
The LdL code means that the lid of your washer isn’t closed completely and locked. Fixing this issue requires checking the entire perimeter of the...
How to Fix Maytag Machine LdU Error Code
This code means that the washer lid will not lock. Removing something heavy like a bulky blanket from the top of the washer may free up the locking...
How to Fix Maytag Machine LF, Lo FL or F8 E1 Error Codes
For troubleshooting Maytag washing machine with this error code, check the water inlet valve and faucet where the water is entering the washing mac...
How to Fix Maytag Machine Lid Error Code
Make sure the washer lid is closed completely and level. The cycle will reset if the lid is left open for longer than ten minutes. This reset cause...
How to Fix Maytag Machine Ofb Error Code
When the washer is out of balance and running a load-balance correction routine, allow the washer to keep going through the routine. Then, there ar...
How to Fix Maytag Machine OL Error Code
This message means that the washer is overloaded. Take some of the wet clothing out of the washer and place it to the side. Close the lid and press...
How to Fix Maytag Machine PF Error Code
Touch and hold the START button to reset the washing machine cycle.
Are you pressing and holding the Start button?
You may need to press and hold the start button for up to 3 seconds to engage the cycle.
Is the lid completely latched?
The lid must be completely closed and latched for the washer to operate.
Did you receive an "LF" or "F8E1" Error Code, or is the Spin or Wash light blinking?
If F8 E1 or LF (too long to fill) appears in the display, the washer is taking too long to fill or the washer is filling and draining.
Are you using anti-flood devices and controls?
Whirlpool recommends that appliances be directly connected to the water supply for optimum machine performance.
Is the Control Set Correctly?
Make sure the selector knob is lined up with a cycle selection and the start button has been pushed. The washer will not start if the selector is not placed on a cycle selection. Set selector to the desired cycle, like Normal, and push the start button.
Still need help? Contact us or schedule service
Please contact us or click below to make an appointment from our preferred list of service providers for service on your appliances.
Interested in purchasing an Extended Service Plan?
Please click below to learn more on how you can save up to 25% on New Appliance Extended Service Plans within 30 days of your appliance purchase.
Why is my Maytag washer sensor light on?
This is primarily caused by the shift actuator not being able to engage the drive shaft to respond to the washing machine’s commands; it could also be caused by wiring that has failed.
What is the problem with Maytag washers?
Maytag washing machines are built-to-last, but there can be some common problems, just like all other washer models. The sensing lights all correspond to a specific problem with the unit, and thankfully, these problems are easily fixed with DIY methods. Overall, many of these error codes point to a faulty shift actuator that can easily be replaced.
Why does my Maytag washer light blink?
When a Maytag washer sensing light is blinking, this is usually because the appliance is experiencing an issue where the motor cannot engage with the chosen command. This could be because the lid is not properly closed, or the chosen setting does not produce enough water for the load. A Maytag washing machine’s sensor light will blink ...
What is a Maytag washer?
Maytag’s washing machines are known for durability and dependable mechanical features that ensure thorough cleaning and easy-to-use settings. Like all appliances, even Maytag washing machines have moments where mechanical glitches can arise. Maytag washers have an array of lights that alert you when something is not right ...
How to fix a faulty water inlet valve?
To fix a faulty water inlet valve, you can use a multimeter to check the coils on the valve that pick up the electric commands sent out by the washer. If the coils still have a path of voltage to the washer, this may not be the problem.
Why is my Maytag sensor not working?
If the sensor lights on your Maytag are not working at all, the control panel may have malfunctioned. Control panels can short circuit as time goes by. Additionally, this could be caused by not resetting the error codes after replacing a new part. To check this problem, run a diagnostic test for error codes.
Why does my tub light flash?
A flashing fill light could have a few different causes. There could be a problem between the electronic sensors that provide directions to the water inlet valve. The water level switch could be going out, and in this case, you may notice the tub only filling halfway with water or not at all.
Is there anything blocking the latch?
Ensure the door latch is not blocked. Below are some everyday items that may prevent the washer from latching:
Does the latch need to be cleaned?
Check to make sure there is no soil build-up on the door contact area. If this area does need to be cleaned, use the following: warm water, mild soap, and a soft cloth.
Was the cycle just started?
When the Start/Pause button is touched, the washer will first perform a self-test on the lid lock mechanism. You will hear a click, the basket will make a slight turn, and the lid will unlock briefly before locking again.
Still need help? Contact us or schedule service
Please contact us or click below to make an appointment from our preferred list of service providers for service on your appliances.
Interested in purchasing an Extended Service Plan?
Please click below to learn more on how you can save up to 25% on New Appliance Extended Service Plans within 30 days of your appliance purchase.
Maytag Washer Not Filling: What To Check?
Several things could be causing water flow issues with your Maytag washer. It could be either a problem with the drain hose or with the water inlet hose or filter.
Finishing Up
After you’ve cleaned the inlet hose filters, put them back into the hose along with the rubber gasket. Reattach and turn the water back on. You will need to reset the washing machine and run a diagnostic cycle to make sure it’s working well.
How often will I need to clean out drain hoses or inlet hoses?
You shouldn’t have to clean out the hoses on your Maytag washer often. It really depends on how many loads of laundry you do daily. Clogs occur when the lint, hair, and fabric threads accumulate from laundry over time and get caught in one of the hoses.
Can I put an anti-flood control or device on my washer?
Maytag experts state this isn’t a good idea because it could interfere with water properly flowing into your washer within the correct time programmed on the washer’s control panel.
What does LF stand for?
The LF in the washer code error means “long fill.” It means the washer is taking too long to fill up with water. The main control will shut down if it doesn’t get a signal from the water pressure sensor indicating the water is at the proper level. The error pops up when the control panel shuts down.
How can I get into the diagnostic mode on my Maytag washer?
Running a diagnostic test should be done with caution. There are moving parts working and the tests bypass some of the machine’s safety features.
Can I drain my Maytag washer manually?
Yes, you can drain your Maytag washer manually but it will take a bucket, some towels, and time.
