If the switch is damaged or has failed electronically, it’s possible the Whirlpool washer lid won’t unlock or signal a cycle to start. When this happens, you’ll find your washing machine isn’t spinning, draining, or starting.
Full Answer
Why won’t my Whirlpool washer start?
If your Whirlpool washer isn’t starting, it could be any one of a number of issues, including power issues and clogs. Get the lowdown on what these potential problems are and how to troubleshoot your issue by reading below.
What do I do if my Whirlpool top load Washer won’t unlock?
Whirlpool top-loading washers have several safety features, including a lid lock that ensures the washer won’t start if the lid is open. Although this facilitates safe operation, what do you do if your Whirlpool top load washer won’t unlock due to a malfunction? Bypassing the lid lock with a magnet can enable the use of your machine.
Do Whirlpool washing machines have spin cycle problems?
Whirlpool has been making washing machines for over 100 years. Their range of models features top-loaders, front-loaders, and washer-dryer combinations. Occasionally, even the highest quality models may have an issue with the spin cycle. The most common causes of the issue can be fixed by following this guide.
Why does my Whirlpool washer stop mid-cycle?
Often, a homeowner can easily remedy the issues with a Whirlpool washer that stops mid-cycle. Check the circuit breaker on the electrical circuit that serves your Whirlpool washer. If the washing machine is heavily loaded, the circuit may have tripped.
How do I reset my Whirlpool top load washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
Do Whirlpool washers have a reset button?
While most Whirlpool washers can be reset by disconnecting the power, some models may have different instructions. You may be able to find the specific reset instructions for your model either in the manual or by locating the washer's tech sheet, which is usually located under the control panel.01-Nov-2021
Why does my Whirlpool washer not want to start?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home's main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.23-Feb-2021
Why does my washer turn on but not start?
First, make sure the power is on and that the machine is plugged in. You should check the outlet to make sure it's working. Then, check if a fuse is blown or a circuit breaker thrown. If those both work, see if the Delay Start button or Control Lock feature has been activated.
How do you reset the sensor on a Whirlpool washing machine?
0:031:50Whirlpool washer reset calibration - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst you need to reset the selector. By turning it counterclockwise. Couple of clicks.MoreFirst you need to reset the selector. By turning it counterclockwise. Couple of clicks.
Will unplugging a washing machine reset it?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I get my Whirlpool washer to start?
Washer needs a reset: Resetting the machine can cycle its power, enabling it to start again. Unplug the washing machine or turn off its power at the circuit breaker. After one minute, restore power and try starting the washer.01-Jun-2021
How do I get my Whirlpool washer to turn on?
0:061:03How to Start Using Your New Whirlpool Top Load Washing ...YouTubeStart of suggested clipEnd of suggested clipMachine start by selecting your soil. Levels. Next choose the water temperature you would like toMoreMachine start by selecting your soil. Levels. Next choose the water temperature you would like to use now select your cycle. This should reflect the type of laundry that you're washing.
How do I turn on my Whirlpool top load washer?
1:061:27Whirlpool Washers - How to use your washing machine? - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou can open the lid of the washer by pressing stop then add the garment you want close the lid andMoreYou can open the lid of the washer by pressing stop then add the garment you want close the lid and press the start button again.
Do washing machines have a reset button?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.29-Dec-2018
How do I check the lid switch on my washing machine?
1:144:30Whirlpool / Kenmore Washer Not Draining - Lid Switch Test - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou want to say 2 meter ohms. And test those two pigs. That's a closed circuit. And that indicatesMoreYou want to say 2 meter ohms. And test those two pigs. That's a closed circuit. And that indicates that the lids closed which thatlet's which is good. Now if your lips closed.
What causes the washing machine to stop from working?
There are a few possible reasons for this: - The locking mechanism could have jammed (maybe some clothes have gotten in the way). - There could be a glitch in the washer's computer. - The washing machine may not be draining properly, leaving the washer door locked and the drum filled with water.
Why won't my washer open?
When the switch comes in contact with the strike, it locks the lid and signals the control panel to begin a wash cycle. The plastic strike can crack, break or become misaligned with wear and tear or if the lid is slammed down. When this happens, it may be unable to engage the lid switch or leave the washer door locked, won’t open.
How to bypass a Whirlpool top load washer lid?
If your Whirlpool top load washer won’t unlock, a magnet can bypass the lock to open the lid. Unplug the washer and move it away from the wall. Remove the top panel by pushing in its retaining tabs ...
How to check if Whirlpool washer is tripped?
If the washing machine is heavily loaded, the circuit may have tripped. If you find the circuit breaker in the tripped position, push it to the fully off position and then flip it back to the on position.
Where is the spin cycle switch on a Whirlpool washer?
This switch is under the lid and is usually easily found by looking for a small round or square hole.
What does a Whirlpool washing machine do?
Your Whirlpool washing machine has a water inlet valve that controls the water the enters the washtub. If the inlet valve fails to open, the Whirlpool washer control will wait for the water to enter before continuing to the next part of the cycle.
Why does my washer vibrate?
Things call fall behind the washer and dislodge the plug. The washing machine, particularly top loaders, can vibrate and walk if the washer tub becomes unbalanced.
Where is the thermal fuse on a Whirlpool washer?
You must first locate the thermal fuse. This fuse location is usually close to the drive motor. Getting to this area may involve removing the back panel of the Whirlpool washer to gain access. Before opening the Whirlpool washer, unplug the power cord from the outlet.
How to diagnose a bad timer?
You can diagnosis a bad timer by accessing the connections on the back of the timer. Use a multi-meter to determine if there is continuity in the timer during the different phases of the washer cycle. A bad timer diagnosis is common. Check every other possibility before changing the timer.
Does Whirlpool have a door lock?
If your Whirlpool washer is a front loading type, it has a door lock and motor switch . This feature prevents anyone from inadvertently opening the door on the washing machine while it is in operation. Open and reclose the door and make sure the latch engages.
Why is my Whirlpool washer not making a noise?
If your Whirlpool Washer model WTW4850HW or WTW4955HW is making no noise and is not working, there is a handful of reasons that it may be malfunctioning. While there are a variety of reasons you may need to troubleshoot your Whirlpool, such as the water not filling enough or overfilling, use this guide only when you are noticing that there is no noise or attempt at functioning from your washer. The reasons it may not be properly working include the following:
What does the back of a Whirpool washer do?
At the back of the washer, you’ll notice the water inlet valve for both hot and cold water. The supply hoses should have a filter screen to catch debris from damaging the Whirpool top load washer. If it is clogged, the water pressure may be too low for the clothes washer to properly function.
How to remove plastic belt guard from washer?
Use a piece of electrical tape to secure the washer lid, and tip the washer on to it’s back. If necessary, ask for help since it is heavy. Use your socket or nut driver to remove the plastic belt guard, and disconnect the drive motor wire connector and the drive belt. You can do this manually, without any tools.
How to get water out of Whirlpool washer?
Once you’ve moved your washer away from the wall so you can easily access it, remove the hot and water supply lines from the inlet valve on the back your Whirlpool using pliers, then twisting by hand. Water will likely spill out.
Why is my outlet not receiving voltage?
Other possible reasons that an outlet may not receive voltage include that the fuse has blown, or the circuit breaker has tripped. Try resetting the circuit breaker to see if this fixes the voltage. Another issue includes a ground fault circuit interrupt, which can cause an outlet to be tripped.
How to check if an outlet is getting the correct voltage?
Test the Current. To make sure that your electrical outlet is getting the correct voltage, use a voltage tester. If it is not receiving voltage, ensure that it is not controlled by a switch that is accidentally turned off.
Why does my Whirlpool washer stop spinning?
The most common reason a Whirlpool top-loader washer stops spinning is a faulty lid switch. The lid switch is a safety measure that prevents the washer from spinning while the lid is open. The lid switch on most top-loader washers can be activated manually using a screwdriver or pencil to push it to simulate the lid being closed. You should also be able to hear the lid switch click when you close the lid. If you cannot, it probably needs to be replaced.
Why won't my washer spin?
Like the lid switch on top-loader washers, if the door lock on front-loader washers is faulty, the washer will not spin. The door lock can be checked for a mechanical fault by inspecting it closely and paying attention to it as you open and close the door. To see if the door lock is faulty due to an electrical fault, you will need to test it with a multimeter. If the door lock is broken, it is likely unrepairable and will need to be replaced.
What happens if the motor coupling breaks?
If the motor coupling breaks, the washer will not spin. When repairing the motor coupling, it is recommended that you do not remove the clutch, as this can be difficult to put back after the brake disengages. Follow these steps to repair the motor coupling: Disconnect the washer from the power source.
Why is my washer not spinning?
Another common reason for a washer not spinning is a problem with the drive belt . The drive belt is responsible for rotating the tub. Over time, the drive belt can become loose or break, which causes the washer not to spin.
Why do clothes need to be placed evenly around the agitator?
If there is an imbalance, perhaps because clothes have gotten caught up on one side of the drum, the motion of the washer is disrupted, which results in a subpar spin cycle. For the same reasons, the washer itself also needs to be balanced.
Does Whirlpool have a spin cycle?
Their range of models features top-loaders, front-loaders, and washer-dryer combinations. Occasionally, even the highest quality models may have an issue with the spin cycle. The most common causes of the issue can be fixed by following this guide.