Where is the thermal fuse on a Maytag Bravos MCT?
This fuse is located on the exhaust duct. If the dryer overheats, the thermal fuse opens to cut off power to the dryer.
How do you change a thermal fuse on a Maytag Bravos dryer?
0:181:27How to Replace a Maytag Electric Dryer Thermal Fuse - YouTubeYouTubeStart of suggested clipEnd of suggested clipPull the wires off of the thermal fuse remove. The mounting screw using a 1/4 inch nut driver. PullMorePull the wires off of the thermal fuse remove. The mounting screw using a 1/4 inch nut driver. Pull the fuse off of the blower housing. Position the new fuse.
Where is the thermal fuse on Maytag Bravos XL dryer?
The thermal fuse for your model is on the top of the blower wheel housing. The service manual tells you how to access it after you remove the front panel.04-Apr-2018
How do I reset my bravos MCT dryer?
Full Reset Disconnect the power to the Maytag dryer and wait 30 minutes. After 30 minutes, restore power and make a new selection. If the problem persists or the dryer will not operate, disconnect power once again and call Maytag for service.
How dO I know if my thermal fuse is blown?
0:062:10Dryer Not Heating? Thermal Fuse Testing, Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the fuse has continuity. It should be functioning properly. No continuity means the electricalMoreIf the fuse has continuity. It should be functioning properly. No continuity means the electrical path is broken and the fuse has blown out thermal fuses come in many shapes and sizes.
How do you tell if a thermal fuse is blown without a multimeter?
You can use jumper wires to test whether a thermal fuse is faulty if you don't have a multimeter....Test a Thermal Fuse with Jumper WiresStep 1: Remove the Thermal Fuse. ... Step 2: Disconnect the Thermal Fuse. ... Step 3: Replace or Reattach the Thermal Fuse.21-Jun-2021
How do you bypass the thermal fuse on a Maytag dryer?
Locate and Bypass the Fuse The thermal fuse will look like a thin strip of white plastic with a wire coming out of each end. In order to bypass the thermal fuse, use electrical tape to tape the two ends together. The thermal fuse will then be bypassed. Turn the dryer on to a heat cycle for no more than 90 seconds.
How do I reset my thermal fuse?
2:524:55Reset Dryer Thermal Fuse / Switch (Dryer won't heat fix) - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo if you have this issue and you keep spot or you trip this you may want to try drilling this. AndMoreSo if you have this issue and you keep spot or you trip this you may want to try drilling this. And then you got a little bit of pressure. And it resets. It.
Where is the thermal fuse on the dryer?
1:163:12Dryer Repair- Replacing the Thermal Fuse (Whirlpool Part# 3392519)YouTubeStart of suggested clipEnd of suggested clipLocation of the thermal fuse is right on the blower housing.MoreLocation of the thermal fuse is right on the blower housing.
How do you put a Maytag Bravos washing machine in diagnostic mode?
0:060:55Whirlpool and Maytag washer diagnostic mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipRight right right left right this will bring this washer a diagnostic mode say you have a whirlpoolMoreRight right right left right this will bring this washer a diagnostic mode say you have a whirlpool Bravos.
How do you run a diagnostic test on a Maytag dryer?
1:522:51Whirlpool, Maytag & Kenmore Dryer - Using Diagnostic ModeYouTubeStart of suggested clipEnd of suggested clipTest we hit our second button once the start button will flash. We hit that. And it goes through andMoreTest we hit our second button once the start button will flash. We hit that. And it goes through and it checks our l1 voltage l2 voltage and heater voltage and then also tells us what our airflow is.
How do I get the error code on my Maytag Bravos dryer?
Unplug the dryer for 5 minutes and the plug the dryer back in. If the code reappears, replace the main electronic control board. A stuck button on the user interface control board causes this code. If you can't free the stuck key, replace the user interface control board.