Where is the fuse for the SRS switch located?
The fuse block is on the driver's side of the engine compartment. Pull out the SRS fuse. In most models, this is fuse #40, located in the lower right corner of the fuse block. Turn the ignition switch to "ON" without starting the engine.
Where is the fuse box for the radio fuse?
Fuse Box: 1 inside the car, next to the Driver's door. The other day i was checking my fuses to see which one went bad when i put in my radio. I removed one by one until i found the bad one.
Where is the MES connector on a fuse box?
The MES connector is a yellow connector at the top right of the fuse box that connects to an empty socket. Unplug it and pull it out. Figure 1. Circled is the MES connector.
Where is the fuse for the OBD scan tool located?
Locate the fuse panel cover and remove it. This is located on the lower left side of the control panel on the driver's side of the car. Find the port that fits the OBD cable and plug the scan tool's cable into this port. Put the key into the ignition and turn it to the "Run" position.
Is there a fuse for the airbag?
The airbag in your vehicle likely a fuse but the fuse does not activate the air bags. Additionally, if your service airbag lights are on, your entire system will be inoperative.
What is an SRS fuse?
The car's onboard computer will turn on the Supplemental Restraint System (SRS) Warning Light if the system will not operate properly or operate outside of intentions. This system is designed to deploy air bags and tighten seat belts when the computer determines the car is in an accident.
How do I reset my SRS?
2:294:02How To Reset SRS Light on a Honda - YouTubeYouTubeStart of suggested clipEnd of suggested clipThis. Okay so you turn the ignition. And you're holding them together like that it's gonna turn offMoreThis. Okay so you turn the ignition. And you're holding them together like that it's gonna turn off release them turn it back on touch them.
Can a blown fuse cause the airbag light to come on?
There are many possible fuses that could be behind this, but fuse #13 is a likely culprit. If your airbag light is on and your rear windshield wiper doesn't work, then it's a pretty good indication that you need to change fuse #13 and possibly others. Blown fuses can definitely cause the airbag light to come on.
How do you change an airbag fuse?
1:213:29DODGE DART AIRBAG FUSE LOCATION REPLACEMENT ...YouTubeStart of suggested clipEnd of suggested clipPull up pull out now right here inside guys you have diffuse numbers on the back side of the fuseMorePull up pull out now right here inside guys you have diffuse numbers on the back side of the fuse box those of your fuse numbers whoever in number those.
How do you check an airbag fuse?
1:424:22Airbag Light Stays On - Cheap and Easy Fix! - YouTubeYouTubeStart of suggested clipEnd of suggested clipSystem with it. So here's our 10 amp fuse this is fuse number two it's right up here near the top.MoreSystem with it. So here's our 10 amp fuse this is fuse number two it's right up here near the top. Top. Left hand corner. And.
How do I fix my SRS airbag?
0:393:28How To Fix SRS Airbag Warning Light AIR BAG On EASY FIX - YouTubeYouTubeStart of suggested clipEnd of suggested clipNow to fix it it's pretty simple. You can turn off the car. Always turn off the car when you'reMoreNow to fix it it's pretty simple. You can turn off the car. Always turn off the car when you're working. With.
How do I reset my airbag light manually?
Turn Your Ignition on and Off. First, turn the ignition switch on. Next, wait for the airbag light to turn on – it normally stays lit for seven seconds before shutting itself off. Then, immediately turn off the ignition switch, and wait three seconds. Repeat the initial steps once or twice before starting the engine.
Can you reset airbag light without tool?
It is impossible in most car models to reset the airbag light without a scanner. This is for safety cautions because you should always repair the fault after the airbag light occurred. Luckily, in many car models, the airbag light will also go away by itself if you have repaired the problem.
What happens if I take airbag fuse out?
It will fully drain the system. No im not kidding. Just pulling the fuses won't entirely remove all power from the system as there are still large capacitors to consider.
What can cause SRS light to come on?
Here are the most common causes of the SRS light:Seat Belt Latch Failure. The SRS contains sensors that monitor when the seat belts are fastened. ... Defective Passenger Seat Occupancy Sensor. ... Corrosion. ... Bad Clockspring. ... Dead SRS Computer Battery Backup. ... Previous Accident. ... Faulty SRS Computer.
How can I bypass the airbag light?
0:014:49How to bypass airbag light and fix your horn with aftermarket steering ...YouTubeStart of suggested clipEnd of suggested clipStart the truck the airbag light will glow solid at first and then it should go. Away. If you pullMoreStart the truck the airbag light will glow solid at first and then it should go. Away. If you pull the resistor the airbag light should start blinking. Again.
Step 1 - Find The Mes (Memory Erase Signal) Connector
Pop open the panel underneath the dashboard to reveal the fuse box. The MES connector is a yellow connector at the top right of the fuse box that c...
Step 2 - Reset The SRS Light
Take a twist a jumbo paper clip into a U shape. Turn the ignition off and connect each end of the paperclip to the pins on the MES connector. Turn...
Step 3 - Troubleshoot The SRS
If the reset didn't work, it means that the SRS is getting an error. This can be caused by the steering wheel, airbags, gauges, or seats being disc...
Where is the SRS fuse located?
Pull out the SRS fuse. In most models, this is fuse #40, located in the lower right corner of the fuse block. Turn the ignition switch to "ON" without starting the engine. Leave the ignition on for about one minute to allow the system a chance to reset. Turn the ignition off.
What does the SRS light mean?
When you see the Supplemental Restraint Systems (SRS) light illuminated on the control panel of your Vehicles it means there is a problem with the airbags or the seatbelt tensioners.
How to reset SRS light on Silverado?
How to Reset the SRS Light on a Silverado. Turn the ignition off. Open the hood. Lift up on the tab on the side of the fuse cover to remove it. The fuse block is on the driver's side of the engine compartment . Pull out the SRS fuse. In most models, this is fuse #40, located in the lower right corner of the fuse block.
How to get SRS light to blink twice?
Unshort the two wires. This will cause the SRS light to blink twice. Turn off the vehicle, wait a minute and start the engine. The SRS light will illuminate once more, and then go off for good.
How to short out a MES connector?
Strip the ends of both wires using a knife. Put one end of each of the wires into each of the holes of the MES connector. Cross the other ends of each of the wires together so that they establish contact . This will short out the MES. Take care not to touch the exposed wire with any part of your body.
What does SRS mean on airbags?
The SRS (Supplement Restraint System) warns you if something is wrong with the air bag system. Sometimes the light comes on when there's nothing wrong with the system at all. Performing a quick reset should shut off the light.
What does the SRS light on a Honda Civic mean?
The SRS light is there to tell you when something is wrong with your airbags, but sometimes it'll stay on for no reason. Here's how you reset it. This article applies to the Honda Civic (1992-2000). The SRS (Supplement Restraint System) warns you if something is wrong with the air bag system.
Why is my SRS not working?
If the reset didn't work, it means that the SRS is getting an error. This can be caused by the steering wheel, airbags, gauges, or seats being disconnected when the ignition comes on. It could also be a bad SRS module.
How long does the SRS light last?
Turn the ignition on, and the SRS light will come on for six seconds before turning off. Disconnect the paper clip as soon as the light goes off. When light comes back on reconnect the paperclip. Wait for the light to go off once more then disconnect the paperclip.
Why does my SRS light blink twice?
The SRS light will blink twice to indicate that its memory has been erased. Turn off the ignition and wait ten seconds to restart the car. The light should come on for a moment then go out. Figure 2. SRS light (highlighted above) will blink twice when it's been reset.
Why is there a SRS light on my car dashboard?
A faulty seat sensor can cause the SRS light to appear on your dashboard. Have it serviced by a licensed professional. At this point, most basic causes can be ruled out, indicating that there may be a serious issue with your safety systems.
Can sensor damage be seen?
Sensor damage may not always be visible, so it's recommended that you leave this job to the professionals! If, on the other hand, the dealer says your sensing and diagnostic module is the only component that needs to be replaced, you might want to consider doing this plug and play replacement at home.
What does SRS stand for on Honda Odyssey?
Honda Odyssey: Reset Airbag Light (SRS) The SRS (Supplemental Restraint System) Warning light on the Honda Odyssey is designed to only come on after the vehicle has been in an accident. If the light comes on otherwise, then there is a problem with the internal diagnostic system.
What to do if you can't reset the SRS warning light?
**NOTE: If you are unable to Reset the SRS Warning Light on the first try, REPEAT the steps. If you are still unsuccessful, contact the dealership for assistance or consult your vehicle user’s manual.
