What size is a 1310 U-joint?
| Series | Cross Width | Cap Diameter |
| 1310 | 3.219 (3 7/32”) | 1.062 (1 1/16”) |
| 1310BC* | 3.219 (3 7/32”) | 2 @1.062 (1 1/16”) 2 @ 1.125 (1 1/8”) |
| 1330 | 3.625 (3 5/8”) | 1.062 (1 1/16”) |
| 1330BC* | 3.625 (3 5/8”) | 2 @ 1.062 (1 1/16”) 2 @ 1.125 (1 1/8”) |
| U-Joint Series | Width Center/Center | Currie Strap Kit P/N |
|---|---|---|
| 1310/1330 | 1.416 in. | CE-4058 |
| 1330 BC* | 1.590 in. | CE-4059 |
| 1350/1410 | 1.666 in. | CE-4060P |
What is the difference between 1310 and 1350 U-joints?
Each series has a very specific cap diameter and overall joint width. Normally the larger the U-Joint the stronger it is. The 1310 to 1350 U-Joint Conversion is a mix of two different series specifications on the same u-joint so that that different sized yokes and driveshafts can be connected.
What are standard U-joints sizes?
Standard u-joints sizes are classified by series, with each series having specific cap diameter and overall joint width. Typically speaking, a higher series number translates to a stronger joint.
What are the parts of a U joint?
Nearly all U-joints have one side that is pressed into a welded-in yoke while the other side bolts into the other yoke. The press-in sides use C-clips to hold the caps in place. There are outside and inside locks, and in most cases they are not interchangeable.
How strong are the U-joints?
The strength of the u-joint depends on several factors, material, design, the presence of a grease fitting, cap size, etc. Take note that the u-joint is only as strong as the smallest series number.
What is the difference between 1310 and 1350 U-joints?
Size and strength. The 1310 series joint is what you would expect to find stock in most Jeep or small trucks. A 1350 series joint/shaft is what you might find in many full size trucks. While it's not 100% accurate, you could say that a 1310 is a "half ton" joint and a 1350 is a "one ton joint".
What is the difference between 1330 and 1350 u-joint?
They are often found in 3⁄4-ton trucks and allow more angularity than 1310 joints but are only marginally stronger. 1350 joints are found in 1-ton trucks and use the wider body of the 1330 joint but with larger trunnions and caps.Jun 1, 2013
How do I know what size u-joint?
You measure from the outer side of the lock ring groove side to side. This gives you the width of the joint lock. You still need to measure the overall width of the joint to make sure it is compatible with the bolt-on yoke.Mar 16, 2017
What size is a 1410 u-joint?
Driveshaft and Driveline Parts > Universal Joints > U-Joints BY SIZE > 1410 Series U-Joint 4.188 X 4.188 - 1.188 outside snap ring > 1.188 X 1.188 Bearing Cap Diameter.
Are all 1350 U-joints the same size?
Standard u-joints sizes are classified by series, with each series having specific cap diameter and overall joint width. Typically speaking, a higher series number translates to a stronger joint....Understanding U-Joints.Series1350Cross Width3.625 (3 5/8”)Cap Diameter1.188 (1 3/16”)Spicer P/N5-1350X4 more columns•Jan 6, 2020
How strong is a 1350 u-joint?
The 1350 U-joint is rated for 2,200 lb-ft (minimum elastic limit) of torque.Sep 12, 2019
What is a 1350 yoke?
The forged 1350 steel pinion yokes are designed for Spicer 1350 series universal joints, forged for maximum strength, precision machined, heat treated for toughness, built with U-joint-style joint retainers, and available with the appropriate nuts, washers and u-bolt.
How many U-joints does a Silverado have?
you will find three U-joints on a Chevy Silverado. The rear U-joint is in the rear end of the vehicle. The front U-joint is in the front of the vehicle, and the axle is in the middle.Dec 28, 2021
What is the difference between 1410 and 1415 U joint?
READ THIS: The 1415 series AAM universal joint is just . 007 NARROWER than the Spicer 1410 series. The bearing cap diameter is exactly the same for both. The two are not interchangeable and great care should be taken to be sure of the manufacturer of your driveshaft before ordering and installing any universal joints.
What are the different types of u-joints?
There are two types of universal joints, defined by their number of bending joints:Single joint: has only one bending aspect and is capable of operating at up to a 45-degree angle.Double joint: utilizes two bending joints, the double u-joint can operate at angles up to 90 degrees.
How strong is a 1310 U joint?
According to Spicer, the 1310 joint is rated at 400 lb-ft of continuous torque (down the track) and 800 lb-ft of short-term torque (launch at the line). The 1330 has the same size caps as the 1310, but the U-joint cross is the same size as a 1350.Apr 17, 2014
What is conversion U joint?
Conversion or combination u-joints include a mix of two different series specifications in the same joint so that that mismatched yokes and driveshafts can be connected. The caveat is that the joint is only as strong as the smaller series.
What determines U joint strength?
U-joint strength depends on many factors, including material type, body design, the presence of a zerk fitting, cap size, etc. The chart below summarizes the continuous lifetime operating torque and yield torque values (the point at which the u-joint begins to deform)
What is the angle of a U joint?
as a rule of thumb, the angle of a driveshaft should not exceed 22 degree s. however, some manufacturers do make quality high-angle driveshafts that operate dependably from 22 to 80 degrees.
How long does a U joint last?
Rated lifetimes are on the order of 3000 hours.
How many cardan joints are there in a single cardan drive shaft?
Single Cardan: Single Cardan is a term for a driveshaft with one universal joint at each end of the assembly. So actually there are two single cardan joints in a single cardan drive shaft. Double Cardan: Double Cardan is a term used when describing a one piece driveshaft with three (or more) universal joints.
What is universal joint?
A universal joint in its simplest form consists of two shaft yokes at right angles to each other and a four point cross which connects the yokes. The cross rides inside the bearing cap assemblies, which are pressed into the yoke eyes.
Why are U joints rebuildable?
The joints are rebuildable because the seals, clips, and bushings can be replaced. u-joints like this are very expensive compared to over the counter parts store u-joints but, even under the harshest rockcrawling conditions, should be 10 times stronger than inferior joints if properly maintained.
How much torque does a steering knuckle joint have?
In a driveshaft application, it could be considered as a 2 ton joint. Keep in mind that a steering knuckle joint sees 3-5 times as much torque as the driveshaft joints strictly from the ring and pinion reduction. It is further multiplied by having the steering turned to anything other than straight.
What is a 1410 vs 1480?
The 1410 can be considered a 1.25 ton joint and is appropriate when behind the torque monster diesel engines from the Big Three. 1480 : This joint (farthest right) is most commonly a steering knuckle joint rather than a driveshaft u-joint and resides inside the knuckles of Dana 60 and 70 front axles.
What is the purpose of a U joint?
The purpose of the U-joint is to adjust for the working angles of the suspension. They are the weak link in the driveline, and that is for a reason- replacing the U-joint is much easier than replacing the entire shaft. Where this becomes an issue is when through the course of vehicle maintenance or performance upgrades, ...
Which is better, 1350 or 1310?
For most cars, 1310-series U-joints are typical choice, but for performance applications, the rugged 1350-series joints are the better choice. The larger the series number, the larger the trunnion. Trunnions are the protruding shafts that the caps ride over. Larger trunnions equate to more torsional strength.
Can you change to a larger series U joint?
Changing to a larger series U-joint is not a simple task, you can’t just buy bigger joints . All yokes (slip, bolt-on, and weld-in) must match the desired joint size. You can opt for crossover U-joints, but they tend to not be as strong and they don’t last as long.
Does a spicer U joint have grease?
The Spicer-style, solid-body U-joint comes “lubed for life,” and does not have grease Zerk fittings. This makes them a little stronger because they do not have the stress risers created by the opening for the Zerk fitting in a greasable U-joint.
Can you use a 1350 to 1310 joint?
A 1350-to-1310 joint has a 1350 on one side and a 1310 on the other, allowing you to install the driveshaft until you replaced the slip and bolt-on yokes. While it can be done, using crossover U-joints is not suggested as a long-term solution. The smaller size basically becomes a fuse, and will break eventually.
