What is the space between the ceiling and the floor called?
Especially in multi-story buildings, there's often a space between the ceiling and the floor above (cf. interstitial space).
What is the roof of a house called?
When referring to a specific house (as in your first reference) it's THE roof (specifically the roof of this house), and either THE ceiling or THE ceilingS. Your second reference is talking generally of this space, wherever it is found.
What is the horizontal space between the roof and the wall?
It’s hard to describe the horizontal space , because I can’t see enough of the structure above. The flashing that covers the “joint” (space) between the wall above and the roof below is called “counter-flashing”. Usually there is a piece of metal flashing that is layered into the roofing plies and turned vertically up the wall.
What is the difference between roof and ceiling?
When referring to a specific house (as in your first reference) it's THE roof (specifically the roof of this house), and either THE ceiling or THE ceilingS. Your second reference is talking generally of this space, wherever it is found. In this case, it is correct to say A roof and A ceiling (ie any roof and any ceiling).
What is the space called under the roof?
AtticAttic. The space under the roof.
What is an unfinished attic space called?
Scuttle Attic Any attic space that does not have a permanent staircase for access is considered a scuttle attic. A typical scuttle attic has a trap door and requires you to climb a ladder or a pull-down staircase to get up into it.
What are attic bedrooms called?
An attic or semi-finished room just beneath the roof of a house. garret. attic. loft. cockloft.
What is a small attic called?
A scuttle attic is an attic space accessed by a small hole in the ceiling. The hole, along with the panel that covers it, is called a hatch. Because the term ''scuttle attic'' refers to the opening rather than the attic itself, you might also see it called a ''scuttle hole'' or an ''attic hatch.
What is the purpose of a scuttle hole?
Well, a scuttle attic is a small hole that allows you access to the attic space or even to access to the roof. Typically, they are found in older homes and contain attic ladders.
What is a dormer attic?
Located on the slope of your roof, dormers are roofed structures that typically feature windows and increase the height of your ceiling. Dormer windows are also designed to give your attic or loft additional space, usually adding 30 square feet.
What is the difference between a loft and an attic?
A loft room is accessed by a fixed staircase and has the whole loft area converted to a living space including the sloped eaves if the property has a pitched roof. An attic room is accessed by a fixed staircase and has the eaves area of the loft squared off to create a box room in the centre.
What is an attic space?
Attics are the space between the roof and the ceiling of the highest floor of the house. They're usually full of insulation, and sometimes heating or air conditioning equipment as well.
What is a loft room?
A loft is a building's upper storey or elevated area in a room directly under the roof (American usage), or just an attic: a storage space under the roof usually accessed by a ladder (primarily British usage).
What is a scuttle for an attic?
Basically, a scuttle attic is a hole in the drywall ceiling that leads to the attic with a small attic access panel that covers it. Our small little attic access panel would technically be referred to as a scuttle attic.
Why are attics left unfinished?
The goal with an unfinished attic is to seal it off from the main living space below. This means you should insulate between and over the floor joists. Don't forget to also insulate the attic hatch.
What is a Cockloft in a building?
The cockloft is a void space that is created between the top floor ceiling and the roof decking. ( 1) (1) The cockloft is a void space that is created between the top floor ceiling and the roof decking.
What is interstitial space?
An interstitial space is an intermediate space located between regular-use floors, commonly located in hospitals and laboratory-type buildings to allow space for the mechanical systems of the building. By providing this space, laboratory and hospital rooms may be easily rearranged throughout their lifecycles and therefore reduce lifecycle cost.
Why is it important to separate the building systems?
Separating the building systems from the primary space can also be helpful during construction. If sequenced correctly, it can decrease the installation time of major equipment significantly. Each trade may work on one floor and move to the next after another is finished.
Why are interstitial spaces important?
Interstitial spaces are exceedingly useful when a building needs to be re-modeled. In a medical or lab facility, technology improves incredibly fast and no one can predict what equipment buildings will need to be designed for in the future. With an interstitial space, room layouts in the primary floor may be altered much more easily than traditionally designed buildings since there are fewer service stacks penetrating the floors. The walls can be arranged and rearranged freely. If a drastic renovation must occur, only one floor at a time has to be shut down for renovation, instead of the whole building. The cost of the building is reduced significantly since major equipment does not have to be changed during a renovation. Lifecycle cost includes anything that pertains to the building from when it is in its schematic design phase until it is demolished. A chart of the cost distribution is shown in figure 2. If the equipment itself must be retrofitted, it can be done faster, since the spaces have ample area to work and are separated by floor. The lifetime of the building may also be increased, since the adaptable spaces may be retrofitted instead of needing to be torn down for a redesigned building.
Who was the first architect to use interstitial space?
The first building to actually use an interstitial space design was Louis Kahn ’s Salk Institute of Biological Studies in La Jolla, California.
Do interstitial spaces need to be shut down?
If changes or maintenance need to be performed in the interstitial space, the primary space does not need to be shut down, which is important in buildings like hospitals where the equipment in the space must operate constantly. Unlike traditionally built buildings, where the mechanical space is located in the basement or on the top floor, ...
House Parts Defined
Ever tried pointing out an architectural detail to somebody, only to fumble for what to call it? Or put in a call to a contractor to fix a part of your home and have to call it "you know, that thingamajig"? Don't worry, it's happened to all us.
Bargeboard
A board attached to the edge of a gable roof. In house styles such as Gothic Revival and Tudor, bargeboards often bear intricate carvings or colorful painted details. Also called vergeboard or gableboard.
Check Throat
The groove cut into the underside of a windowsill that prevents rainwater from reaching the wall.
Cricket
A second, small, pointed roof that diverts rainwater around something, such as a chimney, that projects out of a primary roof.
Efflorescence
The weathering on exposed bricks or stones that looks white and powdery. It appears when natural salts in the materials leach out and crystallize.
Enfilade
A series of doors to connecting rooms arranged so that there is one uninterrupted sight line.
Haunch
The curving part of an arch that's bookended by the peak of the arch and either a capital or molding abutment.
What is a weep hole in a brick house?
1. In brick/masory homes the vertical slots are called weep holes. Their purpose is to allow the rain water that soaks through the brick to come back out. From what I learned, about 10% of what gets on the brick passes through since the brick is porous. On the back side of the brick there is a drainage plane, or surface ...
Can you put flashing down over a weep hole?
However, because you have weep holes, you’ll need to allow the moisture to run out ...
What is the eaves of a roof?
Eave – The underside of your roof in the area that extend from the fascia boards to your home’s outside walls. Exposure – The area on any roofing material that is left exposed to the elements. Fascia – The exposed boards you see on the front edges of your roof’s overhangs (eaves).
What is overhang on a roof?
Overhang – That portion of the roof structure that extends beyond the exterior walls of a building. Overdriven – The term used for fasteners driven through roofing material with too much force, breaking the material. Overexposed – Installing shingle courses higher than their intended exposure.
What is outside corner siding?
Outside Corner – A trim piece used to mate courses of siding on a 90 degree outside corner. Panel Projection – The amount that a panel of vinyl sticks out away from the wall; you should choose the largest profile for the style of panel you want. Panel Siding – Siding, which comes in sheets, normally 4 feet by 8 feet.
What is a cricket on a roof?
Crickets – A peaked water diverter installed behind chimneys and other large roof projections. Effectively diverts water around projections. Cupping – When shingles are improperly installed over an existing roof or are over-exposed, they may form a curl or cup. May also be due to a manufacturing defect.
What is panel siding?
Panel Siding – Siding, which comes in sheets, normally 4 feet by 8 feet. Examples of panel siding include Texture 1-11. Because panel siding can be installed quickly, it can be a less expensive option than other types of siding. Plywood siding – Plywood sheets, some with a grooved or decorative outer surface.
What is the pipe that directs water from the roof?
Downspout – A pipe that’s fastened to the sides of your home and directs water from your roof’s gutters away from your house. Drip edge – A strip of material (typically metal) installed along the roof edges so water won’t drip onto the eaves, siding, or deck.
What is corrugated siding?
Corrugated Siding – Siding made out of aluminum or plastic derivatives having ridges and valleys and is attached to the sides of buildings. Course – A row of panels, one panel wide, running the length of the house from one side to the other or, in the case of vertical siding, from top to bottom.
