What does the ICP sensor do on a PowerStroke?
What is the ICP sensor on a 6.0 Powerstroke? It senses the pressure in the high-pressure oil system and reports back to the engine computer which in turn adjusts the IPR valve position to achieve the desired pressure for a particular desired engine speed and load. The ICP, ECM, and IPR form a closed loop feedback system. Click to see full answer.
What should the idle speed of the ICP sensor be?
If the PCM does not receive data from the ICP sensor, it will fall back to a default ICP of about 700. If the sensor is working properly, the idle speed should be about 500.
What are the symptoms of a bad ICP sensor on a diesel?
7.3 Powerstroke ICP sensor failure symptoms include: The worst symptom of a bad, i.e. failed, ICP sensor on your 7.3 is that your engine just won’t start at all. But, to tell you the truth, so many failed parts on your 7.3 diesel cause the exact same symptoms that it’s hard to tell what’s not working.
How much torque does it take to replace an ICP sensor?
The replacement ICP sensor takes a 1-1/16″ deep socket or wrench. Step 5 – Torque your new 7.3 ICP sensor to spec – 9 lb./ft. – 108 INCH pounds. Step 6 – If your ICP pigtail is coated with oil, cracked, or frayed replace it.
What does an ICP sensor do?
The injector control pressure (ICP) sensor is on both the 7.3L and 6.0L Powerstroke engines. They use a high pressure oil system as a way to pressurize fuel in the injector body. ICP sensors on the Ford 7.3 diesel engines read the oil pressure in the HPOS.
How do you check an ICP sensor on a 6.0 Powerstroke?
3:069:30Testing the Icp voltage on the 6.0 powerstroke . DieseltruckpartsdirectYouTubeStart of suggested clipEnd of suggested clipYou can do that we can monitor actual voltage all the time. So we just have this to go in seriesMoreYou can do that we can monitor actual voltage all the time. So we just have this to go in series with it we're going to unplug the ICP sensor. Put it in reconnect it here.
What should the ICP read on a 6.0 Powerstroke?
6:157:47P2285 ICP sensor tips and tricks on the 6.0 Powerstroke. (03 shown)YouTubeStart of suggested clipEnd of suggested clipSo now the ICP is reading roughly 15 psi but voltage is there.MoreSo now the ICP is reading roughly 15 psi but voltage is there.
What is a ICP on a diesel truck?
The ICP or Injector Control Pressure sensor is an essential part of your Ford Diesel engine. This electronic part communicates how much pressure is needed to determine the amount of fuel to deliver to the motor.
Where is the ICP located on a 6.0 Powerstroke?
0:001:07HOW TO REPLACE ICP SENSOR ON 6.0 POWERSTROKE in 1 MINUTEYouTubeStart of suggested clipEnd of suggested clipIn one minute i'm going to show you how to replace the icp sensor on 6v power stroke let's getMoreIn one minute i'm going to show you how to replace the icp sensor on 6v power stroke let's get started injection control pressure sensor is located on passenger side valve cover.
What does the ICP sensor do on a 6.0 Powerstroke?
INJECTION CONTROL PRESSURE - The ICP (Injection Control Pressure) Sensor is responsible for detecting the pressure of the oil feeding the injectors in the Ford 6.0 Powerstroke. A faulty ICP Sensor can cause all kinds of problems. Poor idle, stalling, surging, or not even allowing the engine to start at all.
What is a good ICP reading?
In the horizontal position, the normal ICP in healthy adult subjects was reported to be within the range of 7–15 mm Hg. In the vertical position it is negative with a mean of around −10 mm Hg, but not exceeding −15 mm Hg.
What are normal ICP readings?
For the purpose of this article, normal adult ICP is defined as 5 to 15 mm Hg (7.5–20 cm H2O). ICP values of 20 to 30 mm Hg represent mild intracranial hypertension; however, when a temporal mass lesion is present, herniation can occur with ICP values less than 20 mm Hg [5].
Where is the injector control pressure sensor located?
0:052:48Ford 6.0L Powerstroke Injection Control Pressure (ICP) Sensor ...YouTubeStart of suggested clipEnd of suggested clipAnd early all fours have the ICP sensor mounted back here above. The high pressure oil pump newer.MoreAnd early all fours have the ICP sensor mounted back here above. The high pressure oil pump newer. Ones Oh 5 and later for sure have the ICP mounted on the passenger side valve cover.
What is an ICP valve?
The IPR valve and ICP sensor work together as part of a feedback cycle to control the oil pressure to the injectors in the HEUI fuel system. The ICP reports the actual pressure to the PCM which then makes an adjustment in the position of the IPR valve to bring actual pressure into sync with desired pressure.
What would cause a 7.3 not to start?
Injector Control Pressure Sensor: When an ICP is failing, the engine runs extremely rough as load is imposed (under throttle), and the condition can eventually contribute to a 7.3L's inability to start. Oil contamination in the wiring usually is the cause.
How do I test my 7.3 ICP sensor?
7:5610:33Ford Powerstroke 7.3 ICP sensor-Easiest way to diagnose it!YouTubeStart of suggested clipEnd of suggested clipDeal disconnect it go try to crank it if it cranks up and it fires. More than likely this ICP sensorMoreDeal disconnect it go try to crank it if it cranks up and it fires. More than likely this ICP sensor is bad.
How do you test a 6.0 IPR valve?
1:1712:13IPR 85% testing the Ford 6.0 Powerstroke diesel - YouTubeYouTubeStart of suggested clipEnd of suggested clipUp. Okay I have the fitting in it's good and cook the air up a couple warnings. One if you hook theMoreUp. Okay I have the fitting in it's good and cook the air up a couple warnings. One if you hook the shop air up to it you are pressurizing this system over a hundred pounds.
Where is the injector control pressure sensor located?
0:052:48Ford 6.0L Powerstroke Injection Control Pressure (ICP) Sensor ...YouTubeStart of suggested clipEnd of suggested clipAnd early all fours have the ICP sensor mounted back here above. The high pressure oil pump newer.MoreAnd early all fours have the ICP sensor mounted back here above. The high pressure oil pump newer. Ones Oh 5 and later for sure have the ICP mounted on the passenger side valve cover.
What is a IPR sensor?
The IPR valve and ICP sensor work together as part of a feedback cycle to control the oil pressure to the injectors in the HEUI fuel system. The ICP reports the actual pressure to the PCM which then makes an adjustment in the position of the IPR valve to bring actual pressure into sync with desired pressure.
How to diagnose a failed ICP sensor?
One quick way to diagnose a failed 7.3 ICP sensor is to lift the plastic clip on the wiring connector and remove the pigtail from the sensor. If there’s oil on the sensor’s plug receptacle, its leads, or around the pigtail connector, you’ve got a failed ICP sensor.
What is the ICP sensor on a 7.3?
The ICP sensor on your 7.3 Powerstroke diesel is a pretty common failure item. When it does fail the good news is it’s relatively easy to diagnose, remove, and replace with a new part to get you and your 7.3 Powerstroke back on the road.
What should ICP be for 7.3?
At WOT in neutral your 7.3 ICP should be – 1100-1200psi – With a caveat that after s/n 896812, after 3 minutes of WOT with no load, the number would be 1800psi. Because at WOT, your 7.3 ICP pressure number will spike and then level off if you stay on the throttle.
What is the code for OBD II?
If your Check Engine Light – CEL – comes on and you have a diagnostic tool to read the OBD-II trouble code, a code of P2285 or related ICP codes P2283, P2284, P2286, and P2287 point to trouble in your 7.3’s ICP sensor electrical circuit or the sensor itself.
Can oil cause bad electrical readings?
When it does, the oil will cause bad electrical readings as well as corrode the sensor’s ability to send those signals. Here’s how to further test ICP sensor 7.3 as the cause of whatever above symptoms your Powerstroke’s having. With your engine running, pull the connector, disconnect your 7.3 ICP pigtail.
Is 7.3 ICP sensor OEM?
Given that an ICP sensor’s a pretty simple part, this 7.3 ICP sensor is OEM, it works, and will most likely get the job done with a minimum of headache.
What is an ICP sensor?
The ICP (Injection Control Pressure) Sensor is one of the most critical sensors on the 6.0L Powerstroke Engine. It senses the pressure in the high-pressure oil system and reports back to the engine computer which in turn adjusts the IPR valve position to achieve the desired pressure for a particular desired engine speed and load. The ICP, ECM, and IPR form a closed loop feedback system. Failure of the Ford Powerstroke ICP sensor can cause a very wide range of drivability symptoms. If there is oil in the ICP sensor connector, it needs to be replaced. If your truck will not start, but will start if you disconnect the 6.0L Powerstroke ICP sensor, the sensor is likely at fault.
What happens if ICP sensor fails?
Failure of the Ford Powerstroke ICP sensor can cause a very wide range of drivability symptoms. If there is oil in the ICP sensor connector, it needs to be replaced.
Special offers and product promotions
Amazon Business: Make the most of your Amazon Business account with exclusive tools and savings. Login now
Product description
ICP Sensor manufactured to OEM Spec for 6.0 Powerstroke Diesel Engines.
What other items do customers buy after viewing this item?
There was a problem filtering reviews right now. Please try again later.
