What is the difference between Ford and Holden trailer bearings? LM (Holden bearings) are rated for 750 kg on a 39 mm round or 40 mm square axle. SL (Slimline or Ford) bearings are rated for 1500 kg on a 45 mm round or square axle. With standard bearings, the inner bearing is larger than the outer, but with parallel bearings they're the same size.
Are Holden and Ford bearings the same thing?
The terms Standard bearings or Holden bearings are the same thing. The terms Slimline bearings and Ford bearings are also interchangeable. The simple way to identify your bearings is from the code printed on the bearing itself.
Is there a difference between Holden and Ford trailer studs?
Holden and Ford also use a different stud thread (well they use to) can't remember exactly what they are but. Hrm I worked at a trailer factory about 6 years ago and it was easy back then. The Fords used thicker studs. Only slightly, but you could tell the difference after a seeing a few hundred of each! Sorry I can't be of more help.
Is it worth it to replace boat trailer bearings?
This boat trailer bearing replacement is not a very budget-friendly option to purchase if you are currently short in budget and it especially calls for reloading the bearings properly first when setting it up. It is integral to stringently adhere to the manufacturer’s instructions if you want to avoid future problems.
What are the parts of a trailer or caravan bearing?
A bearing comprises of two parts; the cup which is pressed into the hub and also the cone that contains the rollers. The smaller cup & cone are called the outer bearings, because they fit the outside face of the wheel with the grease cap. The grease seal and inner bearings go on the inside toward the centre of the trailer or caravan.
Are Ford and Holden bearings interchangeable?
Shop All Bearings, Studs The terms Standard bearings or Holden bearings are the same thing. The terms Slimline bearings and Ford bearings are also interchangeable. The simple way to identify your bearings is from the code printed on the bearing itself.
What size are Holden trailer bearings?
Common bearing combinationsBearing typeInner bearing Part numberInner bearing Dimensions (ID x OD x width) in mmLM (Holden)LM67048/1031.750 x 59.131 x 15.875Slimline (Ford)L68149/1034.988 x 59.131 x 15.875CompositeLM67048/1031.750 x 59.131 x 15.875ParallelL68149/1034.988 x 59.131 x 15.87511 more rows
Are all trailer bearings the same?
Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer.
How do I know what bearings I need for my trailer?
The easiest way to determine which bearings are used on your trailer axle is to take the hub off and look for the reference numbers stamped into the metal of both inner and outer bearings. If the bearing numbers are unclear, the next best solution is to take measurements of both bearings. This is the bearing itself.
How can you tell the difference between Holden and Ford trailer hubs?
0:431:51Springwood Marine's 'The Difference Between Ford & Holden ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipSo the only real way to tell is just rule of thumb basically as the barangay. This is the outerMoreSo the only real way to tell is just rule of thumb basically as the barangay. This is the outer bearing if the outer bearing goes over your thumb. That's a ford bearing.
How do you tell a Ford and Holden stud pattern?
0:081:00How to Identify wheel stud patterns on your trailer. - YouTubeYouTubeStart of suggested clipEnd of suggested clipFairly easy way to identify. Them is to go grab hold of your stud measure from the center of oneMoreFairly easy way to identify. Them is to go grab hold of your stud measure from the center of one stud and the next one along if it's 63 mil. Its HT holding on a 5 star if it is 67.
How do I know what bearing I need?
The quickest way to determine which bearing you require is using the bearings reference number. Most bearings have their references numbers engraved on the bearings themselves, but these often rub off over time and so it may be necessary to measure the bearing yourself, as described below.
What bearings do I need?
How to choose the right bearing for your application:Find the Bearing Load & Load Capacity. First, know the type and amount of bearing load that your application will place on the bearing. ... Know the Rotational Speed of Your Application. ... Factor in Bearing Runout & Rigidity. ... Find the Right Lubrication for Your Bearings Needs.
How long do trailer wheel bearings last?
Thanks for any advice. Expert Reply: We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings.
What size is Ford stud pattern?
Find Your Stud PatternStud PatternStud PCDCommon Stud SizeFORD5 x 114.3mm1/2″COMMODORE5 x 120mm7/16″HQ HOLDEN5 x 120.65mm7/16″HT HOLDEN5 x 108mm7/16″4 more rows•Sep 29, 2019
How often should you repack trailer bearings?
How often should you repack your trailer bearings? The axle manufacturers recommend that you repack your trailer bearings once annually or every 12,000 km.
How do you read a wheel bearing number?
1:564:01How to identify a trailer wheel bearing - YouTubeYouTubeStart of suggested clipEnd of suggested clipIt is extremely easy to do. All you need to do is measure the outside diameter of the bearing. TheMoreIt is extremely easy to do. All you need to do is measure the outside diameter of the bearing. The inside diameter and the width of the bearing.
What bearing does my trailer run?
Identifying your correct bearing combination of inner and outer bearings is important when buying new axles, hubs or replacing the bearing s itself to ensure you buy the right combination.
Where are bearing numbers stamped?
Bearing numbers are stamped into the underside of the bearing as shown in the image below: