How to configure Cisco 2960 switch step by step?
configuration. To run Express Setup: Step 1 Verify that no devices are connected to the switch, because during Express Setup, the switch acts as a DHCP server. If your PC has a static IP address, before you begin, you should change your PC settings to temporarily use DHCP. Step 2 Connect the AC power cord to the switch and to a grounded AC ...
What is the default password for Cisco switches?
User accounts and RBAC have the following configuration guidelines and limitations:
- You can add up to 256 rules to a user role.
- You can add up to 64 user-defined feature groups in addition to the default feature group, L3.
- You can configure up to 256 users.
- You can assign a maximum of 64 user roles to a user account.
How to recover a lost password on a Cisco switch?
- Type reset at the rommon 2> prompt. ...
- Type enable at the Router> prompt. ...
- Important: Type configure memory or copy startup-config running-config to copy the nonvolatile RAM (NVRAM) into memory.
- Type write terminal or show running-config. ...
- Type configure terminal and make the changes. ...
How do I set password for switch?
Windows 11, Windows 10, and Windows 8.x
- Press Win -r. In the dialog box, type compmgmt.msc, and then press Enter.
- Expand Local Users and Groups and select the Users folder.
- Right-click the Administrator account and select Password.
- Follow the on-screen instructions to complete the task.
What is the default cisco switch password?
Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168. 1.254. However, some differ as shown in the table below.
How do I reset my Cisco Catalyst 2960 password?
Find the below steps to recovery password for Cisco 2960.Power off the switch first, then press and hold the mode button while you power on the switch again. ... To initialize the flash file system, run the command: ... You can now list the contents of your flash by running. ... To further boot the switch run the boot command as:More items...
What is the default cisco username and password?
The default username is cisco. The default password is cisco. Usernames and passwords are case sensitive.
What is the default IP for cisco 2960 switch?
The switch has a default IP address "10.0. 0.1" and a secondary IP address "10.0. 0.3".
How do I reset my Cisco 2960 to factory settings?
Reset a Cisco 2960 Switch to Factory Default Settings- Start by connecting your cisco switch via a console cable that will be also connected to the same console.Step 2.- Use the following commands: Router: en. Router#erase startup-config. Router# del flash:vlan.dat.- Reload your cisco switch to complete the restoration.
How do I reset a Cisco switch to factory default?
Hold the "mode" button on the front of the switch for 10 seconds. The lights will blink then go solid – the switch completely wipes all configuration and then reboots.
How do I find my cisco username and password?
Cisco Router Login Guide The default username for your Cisco router is Cisco. The default password is Cisco. Enter the username & password, hit "Enter" and now you should see the control panel of your router.
How do I find my cisco Connect password?
Open My Hub > Sessions and find the active session. Click Info. In the expanded Info window, scroll to the AnyConnect Credentials section to see the host, user, and password associated with the active session.
What is default IP of cisco switch?
192.168.1.254To access the switch by using the web-based interface, you must know the IP address the switch is using. The switch uses the factory default IP address of 192.168. 1.254 by default.
How do I connect my Cisco Catalyst 2960 switch?
Follow these steps:Connect the supplied RJ-45-to DB-9 adapter cable to the 9-pin serial port on the PC. Connect the other end of the cable to the console port on the switch.a. Configure the PC terminal emulation software for 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.a.
How do I change the IP address on a Cisco 2960 switch?
Configure an IP address on a switchenter the VLAN 1 configuration mode with the interface vlan 1 global configuration command.assign an IP address with the ip address IP_ADDRESS SUBNET_MASK interface subcommand.enable the VLAN 1 interface with the no shutdown interface subcommand.More items...
How do I login a switch using putty?
Configure putty to be able to communicate with the router over the USB port ( /dev/ttyUSB0 ).run sudo putty.Click on Serial for the Connection Type:Set the serial line to /dev/ttyUSB0.Click on Keyboard, then set backspace key to Control-H.Click on Session . Click on Default Settings. Click Save .Click Open .
What is Cisco IOS password security?
By default, the Cisco IOS software operates in two modes (privilege levels) of password security: user EXEC (Level 1) and privileged EXEC (Level 15). You can configure up to 16 hierarchical levels of commands for each mode. By configuring multiple passwords, you can allow different sets of users to have access to specified commands.
What is the setup program for a switch?
When you power-up your switch for the first time, an automatic setup program runs to assign IP information and to create a default configuration for continued use. The setup program also prompts you to configure your switch for Telnet access through a password. If you did not configure this password during the setup program, you can configure it when you set a Telnet password for a terminal line.
How to provide terminal access control?
A simple way of providing terminal access control in your network is to use passwords and assign privilege levels. Password protection restricts access to a network or network device. Privilege levels define what commands users can enter after they have logged into a network device.
Can you use TFTP to enable password?
To provide an additional layer of security, particularly for passwords that cross the network or that are stored on a Trivial File Transfer Protocol (TFTP) server, you can use either the enable password or enable secret global configuration commands. Both commands accomplish the same thing; that is, you can establish an encrypted password that users must enter to access privileged EXEC mode (the default) or any privilege level you specify.
Can you configure username and password on a switch?
You can configure username and password pairs , which are locally stored on the switch. These pairs are assigned to lines or ports and authenticate each user before that user can access the switch. If you have defined privilege levels, you can also assign a specific privilege level (with associated rights and privileges) to each username and password pair.
What does it mean when your Cisco router doesn't work?
If the default username or password doesn't work, it means that it's been changed. Unlike residential routers, the Cisco business and enterprise-class routers and switches have specific password recovery features, meaning that a full factory reset (the typical reset-a-password process) isn't required.
Do routers have default IP addresses?
Most network devices operate with the default IP address they come with but routers, and especially switches, in business and enterprise environments, are often changed when installed. Learn how to identify network hardware IP addresses on a local network if the default IP isn't working.
