- Coefficient of friction, or COF, is an objective standard of rating how slippery an item is.
- Search COF ratings published by tile manufacturers and retailers.
- Look for higher COF slip resistance numbers.
- Dry, clean items that move against each other are usually COF-rated from 0.3 to 0.6.
- Zero COF means that two items have no friction. ...
What is COF of a tile?
Water … The Coefficient of Friction (COF) of a tile is a measure of the “slip resistance” of a tile. For example, the dry cement patio around a public pool is very slip resistant (so it would get a high rating) and the ice on hockey rink is VERY slippery (so it would get a low rating).
What is the DCOF rating of a tile?
Correct: A manufacturer says that its tiles are rated at ≥ 0.42 wet. Because this is specified as the DCOF AcuTest, its wet ratings are using the current system. This does not mean that ≥ 0.60 wet tiles are unsafe.
What is the minimum COF required for floor tiles?
C.O.F.: Use tiles that provide good traction (COF greater than or equal to 0.60). Water Absorption (W.A.): Water absorption standards vary.
What is a good COF for bathroom tile?
C.O.F.: Use tiles that provide good traction (COF greater than or equal to 0.60). Water Absorption (W.A.): Water absorption standards vary. In general, use: • less than 7% for areas that are occasionally wet (bathrooms, kitchens). Click to see full answer. Also question is, what is COF for tile?
What is a good coefficient of friction for tile?
The Ceramic Tile Institute identifies tile in the following three categories: Slip Resistant: Coefficient of friction is 0.60 or greater (wet). Meets or exceeds general safety and health regulations, ADA and OSHA requirements. Conditionally Slip Resistant: Coefficient of friction is 0.50 to 0.59 (wet).
What does COF mean in tile rating?
C.O.F. (Coefficient of Friction) The coefficient of friction value represents the tile's natural resistance to slip, measured by the force. required to move an object across the tile divided by its weight.
What is a good slip resistance rating for tile?
The measurements require that for level interior floors tiles, wet with water, the minimum slip resistance is 0.42 DCOF and for level exposed exterior floors that are wet with water, the minimum slip resistance is 0.60 DCOF.
What is a good coefficient of friction for shower tile?
0.42There is little agreement on what is suitable, but it is normally accepted to have an average Coefficient of Friction rating of . 6 per ASTM C1028 or DCOF minimum of 0.42 per ANSI A137.
What is a good dynamic coefficient of friction?
Dynamic Coefficient of Friction: ANSI® A326. 3 now includes a method for measuring Dynamic Coefficient of Friction (DCOF) and a recommended value of 0.42 for interior, level floors that are likely to be walked upon when wet.
Is a high coefficient of friction slippery?
Friction Measurements In plain terms, COF measures how slippery a surface is, and how much friction it generates. More friction is better, because more friction means better traction and thus a lower likelihood of slipping. A low COF means there is less friction, and thus, it is easier to fall.
What does R10 slip resistance mean?
Often used to prevent slippage in domestic situations, anti-slip tile ratings of R10 will be perfect for kitchens and bathrooms. Thanks to their anti-slip properties, they can also be used as external floor tiles (porcelain versions only) or commercial tiles.
What slip rating do I need?
A tile with a rating between P0-P3 is generally considered suitable for indoor flooring while a P4 or P5 has a lower slip risk and can be used outside or around a pool.
What is a good slip coefficient?
The U.S. Occupational Safety and Health Administration (OSHA) has recommended an SCOF of 0.50 for workplace environments, but often flooring having a rating of 0.60 or greater (supposedly even more slip resistant than 0.50 flooring) is proven by reliable test devices (and multiple slip and fall accident victims) to be ...
What is coefficient of friction for porcelain tile?
0.42The DCOF standard for porcelain ceramic tile is 0.42. DCOF values of a surface will change over time.
What kind of tile is not slippery when wet?
Terracotta tile, quarry tile, and brick have high COF ratings, so they are very slip resistant. Honed natural stone, slippery like glass, is one of the lowest COF-rated floor tiles.
What is a good DCOF for bathroom floor?
0.42The Dynamic Coefficient of Friction is a measurement that represents how slippery a tile is. According to the American National Standards, when purchasing tiles for a bathroom, ensure that it has a DCOF rating of higher than 0.42, which is.
What is the R10 slip rating?
What is r10 slip rating? The R scale runs from R9 to R13, where R9 is slippery when wet, and R13 the least slippery. Floor surfaces that are classified by the DIN 51130 standard as R9 (or in some instances R10) will be slippery when used in wet or greasy conditions.
What is a COF for tile?
Beside this, what is COF for tile? There is a reliable way to know how slippery floor tile will be under both wet and dry conditions: COF (or coefficient of friction) slip ratings published by tile manufacturers. COF slip resistance ratings help you determine if you are buying the right tile for the right location.
What is a grade 1 tile?
Tile Grading Tiles are graded using a numerical numbering system based on their thickness and quality. A rating of 1 is the highest quality and thickest tile available, 3/4-inch thick, and you can use them anywhere. Grade 2 reflects that some imperfections exist but the tile still is usable on walls or floors.
Why do we no longer use SCOF?
We no longer use SCOF testing because DCOF more realistically measures conditions of walking on tile. DCOF AcuTest® uses slightly soapy water instead of clean water to recreate environments where slipping occurs.
Why are tile sizes important?
Tile sizes are a factor for slip resistance in wet areas. Smaller sizes allow for more drainage through an increased number of grout joints and easier sloping. Planar variations on larger formats could result in a higher probability of standing water and increase the risk for hydroplaning.
What is a DCOF?
DCOF, or dynamic coefficient of friction, is a measurement that determines how much friction there is on wet, level floors when walked upon. The results of DCOF testing help us determine ...
What is pool decking?
Pool Decking (and other wet areas with minimal footwear) edestrian areas that could be exposed to water (excluding ice), but are otherwise reasonably maintained , where footwear is typically used. Some examples are (but not limited to): walkways, gazebos, or patio areas. ≥ 0.60. Oils.
Is Dal Tile slip proof?
ANSI A137.1 requires that tiles suitable for interior level spaces expected to be walked upon when wet have a wet DCOF ≥0.42. No floor tile is "slip proof.".
Does Dal Tile have a test?
Dal-Tile Corporation recommends that customers have tile independently tested to determine if the Dal-Tile Corporation product meets the requirements of the customer's preferred test method (if other than the AcuTest) prior to product selection.
)&qlt=60&wid=1024)