What is a blocked tremolo on a Strat? A: Blocking a tremolo means to set it up so that it can only go down in pitch, not up. Doing so provides a number of advantages: It can add sustain to your tone.
Full Answer
How to put a Floyd Rose on a Strat?
Part 2 Part 2 of 3: Replacing the Strings Download Article
- Buy replacement strings of the same gauge. If you don't know what gauge your old strings are, take your guitar into a music shop and have a tech look ...
- Use wire cutters to snip off the ball end of the replacement string. The ball end of standard guitar strings won't fit in a Floyd Rose bridge.
- Secure the new string at the bridge. ...
Which tremolo is right for your Stratocaster?
Pitch Control: A Tremolo Primer
- Trem Terminology. First, some definitions. ...
- A Trim Trem History. Invented by Clayton “Doc” Kaufman in 1929 and officially patented in 1935, the Kaufman (or Kauffman) Vibrola was the earliest vibrato system put to use on ...
- Behind the Bars. There are two basic types of trem arms, both of which are fairly self-explanatory: Screw-in and pop-in.
How to play tremolo like a boss?
From the Manufacturer
- Provides guitarists with high-quality vintage tremolo effects in an easy-to-use compact pedal
- Dedicated "Wave," "Rate" and "Depth" knobs allow for precise effect tailoring
- "Rate" control allows for higher speed adjustment than BOSS' classic PN-2
- "Wave" control alters LFO waveform from triangle to square
How can I Make my Squier Strat sound better?
How?
- rmcelwee Strat-Talker. ...
- peskypesky -------
- stratmanchu Senior Stratmaster. ...
- peskypesky -------. ...
- rmcelwee Strat-Talker. ...
- rmcelwee Strat-Talker. ...
- vaughndrix Strat-Talker. ...
- Shades of Blue Most Honored Senior Member. ...
- motoman45 Strat-O-Master
- softwarejanitor Most Honored Senior Member. ...
What does blocking the tremolo do?
A: Blocking a tremolo means to set it up so that it can only go down in pitch, not up. Doing so provides a number of advantages: It can add sustain to your tone. It can help keep the guitar in tune after “dive-bombing”
Should I block a Strat tremolo?
While the design is great and they can be set up to play in tune, often that maintenance falls by the wayside and the tuning becomes unreliable. And if you never use the tremolo, blocking it off can get you some great results. You'll get much better tuning stability and, when it's done properly, greater sustain too!
How do you block a Fender tremolo?
1:5610:25How to block a Vibrato/Tremolo like a Fender Stratocaster Eric Clapton ...YouTubeStart of suggested clipEnd of suggested clipSo what you want to do is you want to take these shims and you want to create a very snug. Fit onMoreSo what you want to do is you want to take these shims and you want to create a very snug. Fit on both sides of the tremolo block that's the lower section of the tremolo.
Does Clapton block his tremolo?
Speaking to Vintage Guitar in 2004, Lee Dickson, who has been Clapton's guitar tech since 1979, said that while the guitarist doesn't use a tremolo bar, he likes vibrato guitars, noting, "We block the vibrato behind the bridge and tighten up the (vibrato) springs, so it stays pretty solid.”
How do you block on a Stratocaster bridge?
1:199:57How to block off a tremolo - Hardtail an electric guitar - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd you just kick off all the crafting require. So you get it up and you just push them from theMoreAnd you just kick off all the crafting require. So you get it up and you just push them from the front all the way through the back. Also you've removed all trace of strange.
Does all Strat have a floating bridge?
There are three possible configurations of the Stratocaster Tremolo: Floating, Decked, and Blocked. Floating the trem allows the bridge to be pushed down which loosens the string tension, and pulled up which tightens the string tension.
How do you hard tail a Stratocaster?
0:193:17How to Hardtail Fender Stratocaster Tremolo Bridge - YouTubeYouTubeStart of suggested clipEnd of suggested clipJust. To the floating tremolo sits back flush on the body a white touch thing screws that or justMoreJust. To the floating tremolo sits back flush on the body a white touch thing screws that or just leave them as they are.
What does a Tremsetter do?
The Tremsetter greatly improves guitar performance by automatically returning your full floating tremolo to an exact "zero" neutral position, eliminating flutter and sag, so your guitar remains in tune. You can bend strings, play bridge harmonics, aggressive rhythm parts or mute strings and the bridge remains stable.
What is a decked tremolo?
These are adjustment screws used to fine tune spring tension affecting the bridge. If you want to deck your trem or block your trem, you may add more or stronger springs. The idea is to pull the bridge down to the surface of the guitar body.
How much did Jimi Hendrix white Strat sell for?
If you ever visit Seattle, a trip to the city's Museum of Pop Culture is well worth your time – as here you'll find the iconic white Stratocaster Jimi Hendrix used during his performance at Woodstock. The guitar in question was purchased by Microsoft co-founder Paul Allen, who purchased it for a cool $2 million.
What Strat does Clapton use?
Fender Eric Clapton StratocasterThe Fender Eric Clapton Stratocaster is the signature model electric guitar of English guitarist Eric Clapton....Fender Eric Clapton Stratocaster.Eric Clapton StratocasterHardwareBridgeBlocked Synchronized TremoloPickup(s)(2001–present): 3 Vintage Noiseless single-coils (1988–2000): 3 Gold Lace Sensors12 more rows
What kind of Strat does Eric Clapton play?
Fender Stratocaster electric guitarToday, Eric Clapton is best associated with the Fender Stratocaster electric guitar (he endorses a signature model) and Martin Acoustic Guitars (five models have been issued over the years). In concert, he primarily plays his signature model Fender Stratocaster.
Who blocked the tremolo on a Strat?
Eric Clapton, for instance. If your Strat has a tremolo tailpiece, and you want a hard tail, you can do what Eric did and block the tremolo (which is actually a vibrato, but after decades, the name stuck).
How to block a tremolo?
An easier but very effective method for blocking your tremolo is to tighten the two spring claw plate screws until they are flush against the body (make sure you detune before you do this) Then, make sure that you have all five springs attached to your spring claw and tremolo block.
What wood should I use for a Strat?
Hint: Use a hard wood like maple rather than a soft wood like pine, and make sure you have a snug fit. Once you’ve inserted the block, and string tension is brought back up to normal, you should have, in effect, a hard-tail Strat.
Step 1
Now’s the time to set your action up. If it’s already set, take a measurement at the 12th fret. A good example for most players would be sixth string: 2mm and first string: 1.5mm from the bottom of the string to the top of 12th fret. Make sure that you have set the correct radius curvature on the saddles too.
Step 2
Remove the tremolo cover from the rear of the instrument. If you’ve never looked in here before these springs are the source of that drone you can hear acoustically on your Strat. Tighten the two long wood screws to add more pressure on the spring. That should pull the tremolo heel back downwards to touch the paintwork.
Step 3
The two-point tremolo system makes the tremolo chrome plate float at the front as well as the back. Let’s set the toe down with the flathead screwdriver. Check very carefully that you’re not over-tightening it. The tremolo plate’s knife edge should be sitting in the posts nicely, not resting any higher or even on the threads.
Step 4
Set the other side’s post down using the same method. You can see what happens when you over-tighten the post: it forces the toe down too much and causes the heel of the tremolo to raise up. Play with the height until it’s resting on the paint and not messing with the heel height . Make sure you get both posts right.
Step 5
Now we’ve lowered the tremolo we’ll need to restore the saddles to the same action setting as before using the 12 grub screws on the saddles. The new block wedge is driven in-between the tremolo’s metal body and the tremolo cavity’s wall. The block should have maximum contact with the shape of the metal.
Step 6
Measure the dimensions for the block we need to make. With the length, avoid the rounded edges of the rout as they make it awkward. The width we will add an angle onto. Take note of the measurement between the metal and the rout. We will oversize that and leave a small overhang (as shown in the diagram to the left).
Step 7
Transfer your three measurements onto the timber. We have marked the length and the depth. You may have to play with the depth but it’s the least critical measurement. We’d expect roughly 35mm for depth allowing for a little air gap. We will angle the width later by sanding; it will also be a little oversized, as per the diagram.
How does a decked tremolo work?
A decked tremolo requires tightening of the inertia block with the two tremolo claw screws at the back wall of the tremolo cavity to prevent it from moving. This makes the bridge behave more like a hard tail bridge, eliminating common headaches.
Can a Strat bridge be reversed?
Players are more aware of tuning problems today because of much better electronic tuners that were not around back then. Fortunately this change does not modify the instrument, nor is it permanent. It can always be reversed, making it ideal for collectible instruments that need to stay original. The Strat bridge is decked and basically tightened with the claw screws under the tremolo cover plate in the back of the guitar body. The springs are so tight that the tremolo will not move thereby rendering it a hard tail or a “blocked tremolo” or “decked tremolo”.
What is the floating tremolo system on a guitar?
As one of the most distinctive features on perhaps the most famous (and most imitated) guitars ever, the floating tremolo system as found on the Fender Stratocaster (and other guitars like it) is one of the most-played hardware systems out there. The system allows players to create natural, fluttering vibrato, akin to what early jazz ...
How do I deck a tremolo?
How to Deck Your Tremolo. Step 1: You guessed it, take the plate off the back of your guitar. Step 2: The three springs on this Strat were anchored into the screw claw at an angle, so to accommodate, I moved them over and then slipped on two more springs. Step 3:
How to convert a tremolo bridge to a hardtail?
One involves “blocking” the bridge by wedging a wood block between the trem system and the body of the guitar. The other is to “deck” the tremolo by adding extra springs and tightening the spring claw to deck the bridge against the body.
What does a tremsetter do?
Sitting in place of one of your springs, the Tremsetter counteracts the action of your springs and string tension’s interplay to keep your tremolo in place. You can still get the full action of your tremolo, but the Tremsetter will eliminate any tuning and tremolo flutter problem.
How to tighten trem on guitar?
Tighten down the screw claw to add extra tension on the springs. This will make sure the trem is decked down against the body nice and tight. Start with a turn or two, tune up the guitar and then play it and feel it out. If you feel you need some more tension, flip the guitar back over and repeat.
Can you put a spring block on both ends?
This is especially helpful when you put blocks on both ends of the spring block, as you can’t push your bridge back to un-wedge the block. After that, you’re pretty much done. Tune your guitar, play a bit and see how it feels.
Can you push back on a guitar bridge with a tremolo bar off?
With the trem olo bar off, you really won’t end up pushing back on the bridge much. For most people (myself included) this is enough, but some players want a 100% set bridge. If you decided to drop tune your guitar, the trem can still move forward and cause an issue.
