Receiving Helpdesk

what is a 120 208 panel

by Dr. Diego Daugherty MD Published 3 years ago Updated 2 years ago

When using 120/208V single phase, you will use any two of those same three hot conductors, with the two waveforms peaking 120 degrees apart from each other. ... When one waveform is at its peak, measuring 120V, the other is only part of way through its cycle, measuring only 88V. The sum of the two is 208V.13-Sept-2018

Full Answer

What is the difference between a 208/208 and a 120/120v panel?

But your question sounds like your meaning a panel fed from a 120/208 source which is a WYE and will not have a high leg, on these voltage between any two phases will be 208 volts, and any phase and neutral will be 120 volts. Not a dumb question. If you have a wild leg then you do not have a 208/120V panel you have a 240V delta panel.

What does it mean when it says 120 208 on battery?

If it says 120/208, then it uses both 120 and 208V internally. This means it requires a 4-wire connection. If you are running it on a 3-wire connection, then the neutral and ground are improperly connected together and sharing one wire.

Is 208Y/120 the same as 208/120 Delta?

If you have a high leg it is not 208Y/120. That is delta. 1. Why a high leg at all? What are you supposed to put on it (high leg) when all you need is 120v for computers and lights?

What are the different types of 208v 3 phase power panel?

A 208V 3 Phase Power Panel provides 3 power circuit types (120V 1 Phase, 208V 1 Phase, 208V 3 Phase) in 7 circuit configurations based on Circuit Breaker (CB) Type (1 Pole, 2 Pole, 3 Pole) and Position (1, 2, 3, etc.) as shown below. 208V 1 Phase (Phase A, Phase B)

What is the difference between 120 240V and 120 208V?

120/240V is a 240V single phase supply, center tapped to produce a "split phase" with 120V between either side to neutral, and 240V between the two hot lines. 120/208V is two phases from a three-phase supply. There is 120V from either phase to neutral, and 208V between the phases.14-Jul-2020

What does it mean by 120 208V?

120/208VAC means that power distribution is 3 phase with neutral connection (Y System). 120V represents voltage of each phase to neutral point and 208V represents voltage between any two phases. For balance systems, line to neutral voltage is line to line voltage divided by 1.73 (Sq. root of 3).25-Sept-2003

What is a 208 panel?

0:106:25How is 208 volts different than 230/240 volts? - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd they're splitting that phase into two separate discrete phases with a center tap and that centerMoreAnd they're splitting that phase into two separate discrete phases with a center tap and that center tap is the neutral. So neutral going to the structure goes to the center.

What is 208V used for?

208 volts is Line-to-Line Voltage. This three Phase voltage is frequently used in small businesses.07-Aug-2017

Is 120 and 208 the same?

120/208V Single Phase Power Since the two waveforms peak at different times, the combined power you get from them is less than the numerical sum of the two. When one waveform is at its peak, measuring 120V, the other is only part of way through its cycle, measuring only 88V. The sum of the two is 208V.13-Sept-2018

Can I plug a 208V into 120V?

1 Answer. You'll be fine. What's happening is that 208V 3-phase is "wye" configuration.

How can I get 120V from 208?

Locate and identify the ground or neutral terminal of the 208-volt 3-phase system. Connect the input terminals of your circuit between any phase conductor and the neutral terminal of the system. This connection point will deliver 120-volts to your circuit.07-Aug-2017

What's the difference between 208 and 220?

208V is a line to line voltage of a 208/120Y system. 220V is a line to ground voltage of a 380/220Y system. 240V is the line to ground of a 415/240Y system.13-Aug-2010

Can a 208 be single phase?

In the USA, 208V single phase and three phase voltage is one of the standard voltage levels used for commercial applications. It can be derived from Wye-Wye (Star to Star), Delta-Wye or High leg delta configuration of primary and secondary windings of the transformer.

How do you measure 208 voltage?

The formula is volts times the square root of 3, which happens to be rounded off to 1.732. For 2 lines each carrying 120 volts, the calculation for this is 120 volts times 1.732, and the result is rounded up to 208 volts. That's why we call it a 208 volt three-phase circuit, or a 208 volt 3 phase line.

What is the phase colors for 120 208?

In commercial 120/208-volt medium voltage and 277/480-volt high voltage electrical systems, there are three phases – A, B, and C. Each phase is one of three colors – black, red, or blue for low and medium voltage and Brown, Orange, Yellow for high Voltage.03-Apr-2020

What is the difference between 208 and 480 volt?

208V is the voltage between phases of a 3-phase “Y” circuit that is 120V from neutral to any hot. 480V is the voltage between phases of a 3-phase “Y” circuit that's 277V from hot to neutral.03-Mar-2017

What is the Y in 208V?

The “4 Wire” in 208V 3 Phase 4 Wire refers to the neutral as 4th wire. The” Y” in 208Y/120V refers to the neutral as the center of the Y shaped power source.

What phase should a power panel be balanced?

Ideally, the power circuit loads should be balanced across all three Power phases (Phase A, Phase B, Phase C). You can’t get it perfect, but it’s something to think about. Most Power Panels don’t have a documented load schedule. Below is an example of what one looks like.

Is 208V single phase or 3 phase?

208V Single Phase and 208V 3 Phase power are easy to use, but hard to understand. If you want a simple understanding but aren’t electrically minded, start with a simple analogy you can build on. I like the bicycle analogy.

What voltage to ground for 2 pole breaker?

Voltage to ground will be 208. If a two pole breaker is installed between slot 1 and 3 then you are saying the voltage will be 240v. Click to expand... Phase to phase, yes. Same again for slots 3 and 5. If you put your meter across phase A and ground it reads 120V, phase to ground on B 208V.

Can you use 240V on a three phase load?

You can only do this for a load which is wired delta, giving you 240V on all three line to line connections. This ability to support three phase loads is one of the advantages of high leg delta.

What is the difference between 208V and 240V?

The only difference between the two is that the 208V source systems include an external transformer to step the input voltage up to 120/240V. As an alternative to the step-up transformer, you can opt to use the Break-Before-Make (BBM) maintenance bypass switch.

What UPS system should I use for dirty power?

In cases where the utility power is “dirty” or “’harsh”, you should use a UPS that includes isolation to provide the maximum protection to your equipment. UPS systems that include isolation are considered separately derived power sources per Motorola’s R56 Standards.

Can you use 208V single phase power for UPS?

If you are designing a site that will have 208V single phase power to feed the UPS, you should be aware of the nature of 208V power and how it works with different UPS models. This is one of the subjects that raise the most questions because it is different for the different UPS types, it is something you may not encounter on every project, and it has the potential to be a costly error if ignored.

Can you split 208V into two 120V?

Since most Motorola equipment requires 120V, we need to split the 208V back into two 120V conductors – but it can’t be done. As stated earlier, the power that goes in must match that power that comes out without creating anything new.

How many service disconnects are required for panelboard?

A panelboard having main lugs only shall have a maximum of six service disconnects to de-energize the entire panel- board from the supply conductors. Where more than six disconnects are required, a main service disconnect must be provided. c. Must include connector for bonding and grounding neutral conductor.

What is a box lug?

Enclosures. Boxes are code-gauge galvanized steel except for column type panelboards, which include a painted box finished in ANSI-61 light gray to match the trim. Standard panelboard cabinets are designed for indoor use.

image
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9