The "HC" indicates that the Hot and Cold water supply lines are reversed. Shut the cold and hot water supply valves off and then remove and reverse the hot and cold water fill hoses on the washer and then see if it continues to display "HC". Additionally, what does the code ul mean on a Whirlpool Cabrio washer? Whirlpool Cabrio Washer Error UL.
How do you clear the codes on a whirlpool Cabrio?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid.
- The motor has now been reset and is ready for you to start a cycle.
How to fix a whirlpool Cabrio?
- Disconnect the power to the washer.
- Disconnect the water hoses and move the washer to a suitable location.
- At the rear of the washer, locate three screws on the bottom of the control panel, and remove them.
- Tilt the control panel up and push it forward.
How to reset error codes on Whirlpool Cabrio washer?
To do it, follow these instructions below:
- Go to your display pad and touch any button you see there. ...
- Choose a cycle and press “START.” This might sound crazy, but yes, it’s part of the reset function. ...
- If the error comes back, disconnect your washing machine from the power source. ...
- Plug it back in, and choose any cycle. ...
- If it still hasn’t reset, repeat steps three and four. ...
How to activate diagnostic mode on a whirlpool Cabrio washer?
Whirlpool Cabrio Manual Diagnostic Tests Available In Manual Diagnostic Test Mode
- Water Valve Tests. ➔ START (turns off Fresh valve, cycle indicator is steady on). ...
- Drain Pump & Recirculation Pump Tests. CLEAN WASHER or DRAIN & SPIN ➔ Turns on recirculation pump, the indicator is steady on. ...
- Door Lid Switch Test. Opening the door should cause the Clothes Clean or Done status indicator to turn off. ...
- Door Lid Lock Test. ...
- Motor Circuit Tests. ...
How do you clear the error code on a Whirlpool Cabrio washer?
Write Down The Error Code! Then press PAUSE/CANCEL once to clear the error code and try to start a new cycle. If code appears again put the washer through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea. (Watch The Cabrio Diagnostics Video) This will reveal any stored Cabrio error codes.
How do I clear the error code on my washing machine?
1:073:12Clearing Washing Machine Error Codes Bosch, Neff, Siemens F18 ...YouTubeStart of suggested clipEnd of suggested clipUp press and hold the spin. Button while turning it to the spin. Position for five seconds releaseMoreUp press and hold the spin. Button while turning it to the spin. Position for five seconds release the button turn it to the off. Position. It should have cleared the ever code.
How do you run a diagnostic on a Whirlpool Cabrio washer?
0:061:29Washing Machine Diagnostic Test & Error Codes (Cabrio ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAny one button on the washers control console except for power start or the pause cancel button andMoreAny one button on the washers control console except for power start or the pause cancel button and hold that button for three seconds release. For three seconds. Hold for three release.
Do Whirlpool washers have a reset button?
Follow these steps to reset a Whirlpool washing machine: Make sure the power to the washer is turned on at the wall, but keep the Power button on the control off. Hold the Program button down while simultaneously pressing the Water Level button two times. When done correctly, the control panel lights should illuminate.
What Does the Code OL Error Mean On a Cabrio Washing Machine?
The Whirlpool Cabrio washer giving OL code indicates that you got the washer overloaded. At the beginning of each wash cycle, the inner tub fills with water. But if it’s overloaded to the extent that the inner basket can’t disengage from the motor, the drain pump sucks out water, and the wash cycle fails.
How Do You Clear the Fault Code OL on a Whirlpool Cabrio Washer?
As challenging as it can be, there’s a good chance you can get rid of the OL code without needing professional help. Here’s how:
How Do I Reset My Whirlpool Cabrio Washer?
Resetting the Cabrio washer can stop the OL error code, and it isn’t hard to tackle, so it’s worth trying.
How to Troubleshoot the Whirlpool Cabrio Washer?
The Whirlpool Cabrio troubleshooting process depends on the error code you get. There are several possibilities, some indicating an error with the wash cycle; others are related to the motor, the spin cycle, drainage, and so on.
FAQs About Whirlpool Cabrio OL Error Code
The low water level is significant for a water inlet malfunction; it could be clogged inlet hoses or a defective water inlet valve.
Wrap up
Falling to go into the spin cycle is mostly because of The Whirlpool Cabrio washer error code OL, which stands for “ O ver l oaded.” However, this doesn’t always mean there’s an overload in the literal sense of the word.
Why won't my Whirlpool Cabrio washer lock?
There are plenty of reasons that could lead your Whirlpool Cabrio washer’s door not to lock properly. The problem can be purely mechanical due to the lid lock assembly or a problem with your central control unit. You’ll find below all the possible causes of a dL code.
What causes a Cabrio washer door to lock?
For example, a clogged drain pump or drain hose filter won’t allow a door to unlock, and detergent build-up during a new cycle can prevent the door from shutting.
Why does my washer door latch break?
Broken Door Latch. Sometimes the door latch breaks over time due to mishandling. You could’ve closed the door too roughly, or something heavy could’ve fallen on it. Whatever the reason, the latch broke, and your washer’s door can no longer close.