Samsung DW-FG720 Dishwasher Error Codes
| CODE SYMBOL | MEANING | SOLUTION |
| bE2 | Button key error | Check if any buttons are stuck, or if a ... |
| 3E, AE | Internal communication error | Turn off and restart the appliance. |
| 5E | Drain error | Check whether the drain hose is clogged ... |
| 4E | Water supply error | Make sure the water supply valve open. |
What does se mean on my Samsung dishwasher?
What does se code mean on Samsung dishwasher? In general, the 5E (SE, SC, and 5C) error code appears after the dishwasher completes the program and tries to start draining the dirty water, but it can't. If the water goes through the hose, it means there is a clog in the sewer system, pipe, or siphon under the sink.
What are the error codes on my Samsung dishwasher?
Samsung DMT800 Series Dishwasher Error Codes 1 When the pulse of 100 or less is detected even 73 seconds after the water supply. 2 When flow meter pulse is 5 or less for 13 seconds after the water supply starts. 3 When the water supply does not complete 6 minutes after the water supply starts.
What does the LC or Le error code mean on my dishwasher?
The LC or LE error code appears when the dishwasher's leak sensor detects moisture or the water reflector is blocked (Waterwall models only). When this code occurs, the dishwasher will turn itself on and will not turn off. During this time, it will attempt to drain the water away. If you see a leak, see our guide for dishwasher leaks water.
What do the PC and PE error codes mean on my dishwasher?
The PC error code appears when the Zone Wash function is not operating correctly. Turn off the dishwasher and then try to start the cycle again. If the error still occurs, visit our Support Center to request service. The PE error code appears when the Half load function is not performing correctly.
What does code SE mean on Samsung washer?
An SE error code on your Samsung washer indicates that there is a drainage problem. On some models, the same error is represented by a 5E or nd error code. Be careful not to mistake it for an E5 error code, which indicates that there is a problem with the heating element.
Why does my washer keep saying se?
SE - drain error. Dirty water remains in the drum after washing, so the machine does not start rinsing. In most cases, an incorrectly installed hose is to blame. In second place is a blockage in the drainage system on the third - a broken or blocked pump.
How do you clear a dishwasher error code?
This can usually be corrected by performing the following steps:Press the POWER button to turn the dishwasher off.Turn the circuit breaker to the dishwasher OFF and wait 10 seconds.Turn the circuit breaker to the dishwasher back ON.Press the POWER button to turn the dishwasher ON, and start a new cycle.Oct 12, 2020
Where is the drain sensor on a Samsung dishwasher?
What it is: Inside your Samsung dishwasher, there's a drain filter. This part is located towards the bottom of the appliance, where water pools before it's removed through the drain hose.
How do I fix the SE error on my Samsung dishwasher?
5C, SC, 5E, SE - The dishwasher can't drain.Inspect the dishwasher's drain connection at the sink.Check the drain hose.Run water in the sink that the dishwasher is connected to.Clean the drain, filter, and sump in the tub.
How do I fix the SE error on my Samsung washing machine?
Resolve 5E Error Code on your Samsung Washing Machine Turn off the washer and check that it is level. ... Inspect the drain hose. ... Clean the pump filter (for front load only*). ... Turn the washer back on and start a cycle. ... Request service.Mar 18, 2022
How do you bypass the leak sensor on a Samsung dishwasher?
When the LC code is flashing on your Samsung dishwasher it indicates the unit's leak sensor is detecting moisture or a water leak. If you'd like to simply clear the code it's as simple as unplugging the power cord to the dishwater for about 15 minutes. Doing this should clear the error and reset your dishwasher.
How do you unlock a Samsung dishwasher?
0:080:56Samsung Dishwasher Control Panel Locked | DW80R2031US - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd i can't choose anything you see i'm trying to choose items and all this does is blink. And toMoreAnd i can't choose anything you see i'm trying to choose items and all this does is blink. And to unlock it i similarly. Hold this down for three seconds. And now it's unlocked.
How do I reset the leak sensor on my Samsung dishwasher?
To perform a hard reset, unplug the dishwasher or turn off the power at the main break, and leave it off for about 10 to 15 minutes. This should allow the dishwasher to reset its control board, and at the same time, reset the leak sensor.
How do you force a Samsung dishwasher to drain?
Samsung dishwasher is not drainingInspect the dishwasher's drain connection at the sink. ... Check the drain hose. ... Run water in the sink that the dishwasher is connected to. ... Clean the drain, filter, and sump in the tub. ... Confirm your drain line is not frozen. ... Request service.
How do I clean the drain pump on my Samsung dishwasher?
1:334:56Samsung Dishwasher - Not finishing a cycle - Drain Pump - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd set that off to the side. All right to remove the drain pump there's a little locking tab. RightMoreAnd set that off to the side. All right to remove the drain pump there's a little locking tab. Right here and just gonna go in with the flat-head screwdriver. And just pry it out just a little bit.
How do you clean a Samsung dishwasher drain?
2:466:12SAMSUNG DISHWASHER CLEANING — EASY DIY - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou use a turkey baster to get in and get rid of all the water down here this is where the waterMoreYou use a turkey baster to get in and get rid of all the water down here this is where the water drains out from the dishwasher.
What to do if dishwasher leaks water?
If you're certain that there is not a leak, and if you recently moved the dishwasher, some water may have splashed near the sensor. Give it time to dry. If the noise of the dishwasher is bothersome, unplug it or turn it off at the circuit breaker.
Can you use floodsafe hoses on Samsung dishwasher?
Floodsafe hoses are not compatible with Samsung dishwashers and should not be used. Also, make sure the water supply is turned on. If the error still occurs, visit our Support Center to request service. Drain error. The 5C, SC, 5E, or SE error code appears when the dishwasher can't drain.
Can you connect a dishwasher to a garbage disposal?
If you've recently connected the dishwasher to a garbage disposal, make sure the garbage disposal cap is removed. Finally, make sure the detergent dispenser has not been overfilled or extra detergent added outside of the dispenser. If you continue to get the error, visit our Support Center to request service.
Important Note
The only digital dishwasher can display error codes, while if a dishwasher does not have a digital display, it will blink or flashing some lights to indicate that there is an issue, and it needs to be fixed. Go to Blinking and Flashing Codes to see other errors.
Pump Operation Error
If a 3C error code starts to appear in your machine, then it means that your dishwasher’s pump cannot run anymore, and you can fix this problem by visiting the Samsung Support Centre.
Clogged Filter Error
1E, IE These two errors occur on the Waterwall models of Samsung dishwasher. It tells us that the water is not flowing from the filter. To resolve this problem, you have to lean the filter. If you don’t know how to clean the filter, then you check the user manual based on your model. If the error still occurs, then visit the Samsung Support Centre.
High-Temperature Water Supply Error
When a 3E error occurs, it means the water is too hot inside the dishwasher. To fix this error code, you have to check the water temperature and make sure that it is not higher than 176 degrees Fahrenheit. If it is above 176, then you have to set it below. If this error still there, then visit the Samsung Support Centre.
Water Supply Error
When you see an error of 4C and 4E, you should understand that it is an error of water supply. It indicates that the water pressure or temperature is not enough as it has needed to run the dishwasher properly. To fix this problem, you have to follow these steps.
Drain Error
If you ever see such errors in written 5C, SC, 5E, and SE, understand that your dishwasher is not draining water. Follow these steps to resolve this error.
Water Reflector Error
If your dishwasher has started showing an error of 7E, it means that the reflector is not moving correctly from its position. These are two steps to resolve this issue.
Samsung SE Error Code Meaning
The SE error code gets seen a lot by folks who own a Samsung washing machine, but that doesn’t mean the owner’s manual is always very clear about what the SE error code problem or cause may actually be, which doesn't help troubleshooting.
Samsung Error Code SE Cause and Appliance Background
The control error code SE code occurs when the Samsung washing machine has finished its rinse cycle and then begins to drain the old water out. The machine, under normal circumstances, is supposed to fully exit all dirty soap water and prepare the cavity for fresh clean water for rinse and then spin to fully wring out the clothing inside.
Code Notices and Displays
Again, the standard error code for a drain fault tends to be an SE error, but some washing machines will display a 5E error code instead. They essentially mean the same problem is occurring inside the Samsung washer.
Know When to Call For Help
In most case the SE or 5E error code can be fixed, but folks need to be willing to recognize when the repair needs expert help to fix the problem in their washers.
How to fix microwave SE error?
All you need to do is unplug your microwave from the wall and then turn it back on after a minute or two. If the code has disappeared, you can use your microwave normally.
How to check if microwave is working?
Here’s how to check the control pad: 1 Unplug the microwave from the wall or turn it off from your fuse box. 2 Remove the microwave cabinet – this involves removing a few screws from the back of the microwave, and then it should come off (consult your manual if necessary). 3 Locate the control pad. It is usually found attached to the control panel, which it is connected to by flat ribbon connectors. 4 Once located, the first thing to do is check the connection with a multimeter to determine if there is continuity. If the test shows no continuity, then you’ll need to replace the connection part. 5 You can then remove the ribbon cable from the control board and give the copper connections a good clean with an eraser and alcohol propylene. 6 Next, you can put the parts back together and your microwave back together and then test if the error code is gone. If not, you will have to replace the control panel. You can purchase a new control panel from a parts supplier.
How to tell if microwave control pad is faulty?
You can tell if the control pad is faulty by checking to see if it responds when you press the buttons on it – if the control pad still lights up but the microwave doesn’t respond to pressing the button, then it’s fair to conclude that the control pad is faulty.
