How do you fix the PF code on a dryer?
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.
What does PF error code mean?
power failureExplanation. The PF Error Code indicates a power failure.
How do you reset the codes on a Kenmore Elite dryer?
Unplug the dryer for 5 minutes and then plug it in. If the code returns, then replace the main electronic control board. A button is stuck on the keypad on one of the two user interface control assemblies in the console. If you can't free the button, replace the user interface control assembly with the stuck button.
Why won't my Kenmore Elite dryer turn on?
Always check the dryer venting when replacing a blown thermal fuse. To determine if the start switch is defective, attempt to start the dryer. If the dryer hums but does not start, the start switch is not at fault. If the dryer does not respond or make any noise, the start switch could be at fault.
How do you fix the PF on a Kenmore dryer?
Press the Pause/Cancel/Stop button twice to clear the PF in the display. Try to start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button. Reset the breaker box, unplug the machine for 5 minutes and make sure the machine is securely plugged in afterwards.
Why is my dryer showing PF?
A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. Touch and hold START to restart the dryer cycle or press POWER to clear the display.
What does f1 mean on a Kenmore Elite dryer?
The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.
What causes a Kenmore dryer not to heat?
One of the most common causes for a Kenmore dryer that is not heating up problem could be a clogged vent. Take off the back cover and check to see if there are any objects in it, such as lint or cloths. Be sure to also look at your exhaust pipe too!
Why is my Kenmore dryer beeping?
It's normal for certain Kenmore front-load dryers to beep when a drying cycle ends. The noise is to let you know that clothes are dry and ready to be removed. Some models will beep once, others will beep several times in a series, and some will beep at regular intervals to confirm or remind you that a cycle is over.
When I press the start button on my dryer nothing happens?
To test the switch, open the door press in the door switch lever. If the drum light doesn't turn off, a failed door switch is the likely reason the dryer won't start. A blown thermal fuse often prevents an electric dryer from starting. You'll find the thermal fuse on the blower housing.
How do I know if my dryer fuse is blown?
1:042:10Dryer Not Heating? Thermal Fuse Testing, Repair - YouTubeYouTubeStart of suggested clipEnd of suggested clipIf the needle does not move or the digital display does not change significantly. There is noMoreIf the needle does not move or the digital display does not change significantly. There is no continuity. Which means the fuse has blown out and will need to be replaced.
How do you fix a Kenmore dryer that won't start?
4:016:47Electric Dryer Won't Start - TOP 6 Reasons & Fixes - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst inspect the belt to make sure it's okay if it's broken you'll need to replace it if it's fineMoreFirst inspect the belt to make sure it's okay if it's broken you'll need to replace it if it's fine remove the drum from the dryer.
What does PF mean in a machine?
PF is power failure error meaning electricity has been interrupted to the machine. An electrical interruption of any type can cause a PF error code.
Why do I run a dehumidifier in my laundry room?
I run a dehumidifier in my Laundry room to hopefully prolong the life of my electronics in my washer/dryer.
How to check the operation of a machine?
Try to start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button.
