Why does my Whirlpool washer keep saying OL?
2 Answers. First, OL stands for “Overload”, so in other words, the washer thinks the tub is too hard to move because it's overloaded and the motor is struggling or the unit is way out of balance causing the washer to struggle. The most common problem is a nut below the inner tub that needs to “float”.
What does the code ol mean on a Cabrio washer?
The Whirlpool Cabrio washer giving OL code indicates that you got the washer overloaded. At the beginning of each wash cycle, the inner tub fills with water. But if it's overloaded to the extent that the inner basket can't disengage from the motor, the drain pump sucks out water, and the wash cycle fails.
How do I fix my Whirlpool Cabrio code?
0:112:30OL error code on Whirlpool Cabrio washer after bearing changeYouTubeStart of suggested clipEnd of suggested clipIt basically lets it see or I guess it tells the processor. That it's not overloaded. So the tubMoreIt basically lets it see or I guess it tells the processor. That it's not overloaded. So the tub sort of floats inside of of there the wash tub. Inside of the main tub.
How do I reset my Cabrio Whirlpool washing machine?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do I reset my top load washer?
Motor Reset Procedure:Unplug the washer for 1 minute from the electrical outlet.Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ... The motor has now been reset and is ready for you to start a cycle.
How long does a Whirlpool Cabrio washer last?
about 14 yearsHow long will it last? Top loaders typically have a longer life than front load washing machines. This model should last about 14 years.
How do you run a diagnostic on a Whirlpool Cabrio washer?
3:048:04How to Put #Whirlpool #Cabrio #Washer into Diagnostic Test ModeYouTubeStart of suggested clipEnd of suggested clipSo i just press one two three. And and release one two three. And then until i get to the test modeMoreSo i just press one two three. And and release one two three. And then until i get to the test mode so you have to be very patient to be able to get on the test mode.
How do you reset a Whirlpool washing machine?
Follow these steps to reset your Whirlpool washer:Turn the washing machine off using the control panel.Unplug the washing machine.Wait three minutes.Plug the washer back in, and wait thirty seconds before turning the washer on.
How do you fix the UL code on a Whirlpool Cabrio Platinum washer?
0:0312:11Whirlpool Cabrio Washer uL Code Troubleshooting - YouTubeYouTubeStart of suggested clipEnd of suggested clipMake sure you unplug it or turn off the breaker.MoreMake sure you unplug it or turn off the breaker.
Does the Whirlpool Cabrio have a reset button?
Try the Cabrio Reset Procedure Touch any button that you see on your display pad. This will clear the error code. Or you can press PAUSE/CANCEL. Choose a cycle and press START.How Do I Reset My Whirlpool Washing Machine?https://www.americanappliancerepair.com › appliance-faqshttps://www.americanappliancerepair.com › appliance-faqs
How do you fix a Whirlpool washer that won't drain?
What to Do When Your Washing Machine Won't DrainPerform a Master Reset. Unplug your washer for about one minute. ... Test the Lid Switch Assembly. ... See if the Drain Hose is Kinked. ... Check the Drain Hose or Pump for Clogs. ... Clean out the Coin Trap. ... Check the Water Level Control. ... Schedule Washing Machine Repair.What to Do When Your Washing Machine Won't Drain - Mr. Appliancehttps://www.mrappliance.com › blog › october › what-to-...https://www.mrappliance.com › blog › october › what-to-...