What does LLL mean on ThermoPro? LLL means that the probe was exposed to temperatures below its range and HHH means that it was exposed to temperatures above its range. Click to see full answer.
Why does my digital thermometer say lll?
LLL means that the probe was exposed to temperatures below its range and HHH means that it was exposed to temperatures above its range. Sometimes, doing a hard reset will resolve the problem. Remove the battery. Leave the battery out for at least one minute before installing a new battery.
How do you reset a ThermoPro?
All ThermoPro indoor and outdoor thermometers include a reset button on the front or back of their sensor stations and display units. With forward-facing reset buttons, you can simply press the button to reset them.
How do you fix a digital thermometer error?
Remove the battery and clear the compartment of anything that could prevent the battery from making a good connection, like dirt or debris. Clean out any dirt with a dry cotton swab. Place the battery back inside of your thermometer, making sure the shinier, more reflective side is facing up. Replace the battery cover.
How do I reset my ThermoPro tp19h?
Turn on the thermometer and press the “CAL” button 5 seconds to enter Calibration mode; Press the lock button to undo the calibration and it will reset to the default setting.
Why is my ThermoPro not working?
You might just need to re-synchronize the two devices. Remove the batteries from both the receiver and the transmitter. First, re-insert the batteries into the transmitter. Then, re-insert the batteries into the receiver.
How do I reset my ThermoPro tp50?
Press the button on the back to switch between °C and °F and hold for 2 seconds to clear the record maximum and minimum humidity/temperature readings.
How do I know if my digital thermometer is broken?
Pour cold water into the glass right up to the brim, then stir it for 15 seconds. Insert your thermometer into the water without touching the sides of the glass. After 30 seconds, your thermometer should read 32° F. If it doesn't, it may need to be replaced or recalibrated.
Why is my digital thermometer reading error?
An Err message can appear on the thermometer's display if: the sensor is too warm before powering on the thermometer. the temperature reading is incomplete. the thermometer has an internal problem.
Does low battery affect thermometer?
As long as the thermometer is ready for measurement, it offers the same accuracy. When battery power is too low, the thermometer shows a low battery symbol and does not perform any measurements until the battery is replaced.
What does LL mean on my ThermoPro thermometer?
TP-07 LLL Reading Follow The LLL code will sometimes appear if you stick the food probe in frozen food to indicate that the temperature is below freezing point. To test whether that's the case or not. Take the probe out of the frozen food and see if your thermometer is now reading the room temperature.
Why is meat thermometer not working?
Hold the stem of the thermometer in boiling water for 15 seconds. Assuming you are at sea level, the thermometer should register 212 degrees. If it doesn't read 212 and it's the type in the picture to the right, tighten the screw at the back of it to achieve the correct calibration.
Why is my ThermoPro thermometer blinking?
The unit has a temperature measurement function and an up or down counter timer. The display will slowly flash blue as the temperature rises while cooking. When the temperature rises to within 15º F of the target temp, the blue will change to green to alert the cook that the food is nearly done.
Why does my thermometer have letters on it?
Letters being displayed on your device can be the result of moisture buildup within the probe, water immersion, exposure to excessive heat or flame, or severe bending or twisting of the probe wire. In most cases, the probe has shorted out and will need to be replaced. If you have a digital instant read thermometer that does not have ...
What does it mean when a thermometer is still reading room temperature?
If your probe is still displaying the code at room temperature, it is likely that the probe has shorted out and will need to be replaced. ErrH - This is a code that will sometimes display on digital instant read thermometers. It indicates than an internal error has occurred and it will no longer read temperatures.
What happens if a thermometer is not covered by warranty?
If your thermometer or probe is no longer covered by its warranty, the unit or part will need to be replaced.