What does this error code mean on my Whirlpool front load washer?
This error code is only shown in whirlpool factory test. - Door lock mechanism is broken or removed from door. - Door switchVlock unit failure. 1. Run Quick Diagnostics Test to check motor drive system. 2. Unplug washer or disconnect power. 3. Check door switch/lock unit. 4.
Why does my Kenmore washer have a code on it?
This code will appear at the end of the wash cycle to indicate that cold water hose is connected to the hot water inlet and hot water hose is connected to the cold water inlet. Excessive suds in washer. Washer is running a suds reduction routine.
What does L2 mean on a whirlpool dryer?
“L2” Diagnostic Code. The drum will turn, but there may be a problem with your home power supply keeping the dryer's heater from turning on. Check to see if a household fuse has blown or circuit breaker has tripped. Electric dryers use two household fuses or breakers.
What does the OOP mean on a whirlpool washing machine?
The washer will operate normally, but the regulated water temperatures will not be available (regulated cold and regulated hot). “OP” or “SH” will continue to appear when the control is in idle mode or when a cycle pad is pressed.
How do you unlock the control lock on a Whirlpool washing machine?
To turn off Control Lock, press and hold the Options key that says "Control Lock Hold 3 Sec" under it for 3 seconds.
How do I fix my Whirlpool washer Loc?
Press and hold the Control Lock Key for 3 seconds to unlock the machine. You will notice the machine count down from 3-2-1. The control lock may be a stand alone key, or it could be a dual function key paired with another button like Extra Rinse, Steam, etc.
How do I get the control lock off my washing machine?
Select and hold END OF CYCLE SIGNAL for 3 seconds. The CONTROL LOCKED status light glows. Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off. I hope this is helpful.
How do I reset my Whirlpool front load washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
How do I turn off the Control Lock on my Whirlpool Duet washer?
How to Unlock the Controls for a Whirlpool Duet WasherLocate the "Control Lock/Unlock" button on your Duet's control panel. Video of the Day.Press and hold the "Control Lock/Unlock" button for three seconds.Release the "Control Lock/Unlock" button when the control lock icon on the display disappears. references.
How do you reset a front load washer?
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a "reset" of the washer.
Why does my washer say LoC?
If the control lock has been activated, the control will not function. If you try to push buttons, you may see the code "LoC" or "LC" (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.
Does a Whirlpool washer have a reset button?
Follow these steps to reset a Whirlpool washing machine: Make sure the power to the washer is turned on at the wall, but keep the Power button on the control off. Hold the Program button down while simultaneously pressing the Water Level button two times. When done correctly, the control panel lights should illuminate.
How do I reset the sensor on my Whirlpool washing machine?
0:031:50Whirlpool washer reset calibration - YouTubeYouTubeStart of suggested clipEnd of suggested clipFirst you need to reset the selector. By turning it counterclockwise. Couple of clicks.MoreFirst you need to reset the selector. By turning it counterclockwise. Couple of clicks.
How do I read a Whirlpool error code?
0:173:30Identifying a Whirlpool Fault Code - YouTubeYouTubeStart of suggested clipEnd of suggested clipMany washing machines will display an error code if the machine has a problem Whirlpool machinesMoreMany washing machines will display an error code if the machine has a problem Whirlpool machines with a digital display indicate. This by using a couple of characters on the display readout error