What does FL1 Flo mean on a hot tub?
The error code FL1, FLO or a message " Open Flow Switch " means that your hot tub is not detecting sufficient water movement when the pump is running. In older Jacuzzis, the top-side display will switch between showing the current temperature and the message "FLO".
What does SN1 mean on a hot tub?
Sn1/Sn2. This indicates that there is an open or shorted sensor, which means your heater is disabled and/or your hot tub has deactivated. It is not a good idea to use your hot tub when the sensors are malfunctioning, so call your friendly spa tech for assistance.
How do I fix the FL1 error on my Kenmore hot tub?
If the FL1 error goes away after removing the filters, it is possible that your filters need to be cleaned or replaced . Clean and/or purchase new filters. Reinstall the clean or new filters into the hot tub. Are your jets open?
What does sensor 2 mean on a jacuzzi hot tub?
Contact a Jacuzzi® hot tubs dealer or a service technician. Stands for “Sensor 2” and displays when the temperature sensor is malfunctioning. Indicates a shorted sensor and the heater is disabled. Contact a Jacuzzi® hot tubs dealer or a service technician.
How do you fix a Jacuzzi FL1 error?
If the FL1 error goes away after removing the filters, it is possible that your filters need to be cleaned or replaced. Clean and/or purchase new filters. Reinstall the clean or new filters into the hot tub.
How do you fix an f1 error on a hot tub?
Solution A: Increase the hot tub water level Switch off the power and remove the filters. After 20 minutes, switch the power back on and run the spa/jets without the filters to see if it clears the flow issue. If the flow clears, switch off the power again, replace the filter and then switch on the power.
What does f1 mean on a hot tub?
The error code FL1, FLO or a message "Open Flow Switch" means that your hot tub is not detecting sufficient water movement when the pump is running. In older Jacuzzis, the top-side display will switch between showing the current temperature and the message "FLO".
How do you fix the code on a hot tub?
This error message is similar to the FLO error message. Like FLO issues, this can commonly be fixed by topping off your hot tub water level. DR or DRY will show up if there is little to no water travelling through your heater.
What are the codes on a hot tub?
Hot tub error codesCoLd : Temp in heater housing is below 40° F. ... OH : Overheat. ... HLoH : Hi Limit Over Heat. ... SEoP : Sensor open or disconnected. ... SESH : Sensor short, nonfunctional. ... PSoC : Pressure switch open with circulation pump.PSoL : Pressure switch open with low pump.PSoH : Pressure switch open with high pump.More items...
Why is my hot tub flashing error?
The water probably isn't flowing fast enough through the heater causing the temperature to increase. DO NOT USE THE HOT TUB while these error codes are flashing as the water will be scalding hot.
What does F2 on a hot tub mean?
flow issueThe F2 error code is usually from a balboa power pack system and normally is referring to a flow issue in your hot tub. There are a few things you can look for when trouble shooting an F2 error code on your hot tub. First it is always a good idea to cut the power to the unit and let it cool down and then reset it.
What does FL2 mean?
FL2AcronymDefinitionFL2Facelift Two
Where is the reset button on my hot tub?
1:192:01How to RESET your HOT TUB - YouTubeYouTubeStart of suggested clipEnd of suggested clipGo over to your breaker panel. And flip your breaker or breakers. Down there are some hot tubs thatMoreGo over to your breaker panel. And flip your breaker or breakers. Down there are some hot tubs that have two breakers. And some hot tubs that have one breaker. But you will go to your sub panel.
What does the DR error code mean on a hot tub?
The DR or DRY code indicates a dry heater. This means there isn't enough water in the hot tub to reach the heating mechanism or even worse, there is no water around the heater at all. The DR or DRY code is usually caused by a low level of water in the hot tub or a clogged hot tub plumbing line.
What does flow error mean?
A flow error on your hot tub is a sign that there is an issue with your water flowing through your heater in the hot tub. You can identify a flow error as it will display “FLO” on the front panel. Some common issues that can cause a flow error are: Lower than normal water levels. Damaged and/or dirty filter.
What does Sn1 mean in a jacuzzi?
You can purchase one from your local Jacuzzi® dealer. Sn1/Sn2. This indicates that there is an open or shorted sensor , which means your heater is disabled and/or your hot tub has deactivated. It is not a good idea to use your hot tub when the sensors are malfunctioning, so call your friendly spa tech for assistance. FL1/FL2.
What happens if your hot tub is scalded?
Your scalding hot tub will likely trigger the Watchdog software, which will deactivate the spa and flash red safety lights as a warning. Now that you are in the know when it comes to error codes, you can relax and enjoy your hot tub safely.
What does it mean when you see a dash on your hot tub?
If you see dashes on your hot tub control panel, do not attempt to use your spa. This means that the water is dangerously hot. Call a service tech right away and be sure to secure the cover on your hot tub so that no one else attempts to use it.
What does "col" mean on a hot tub?
COL/COOL. Hot tubs are meant to be hot. This error code means yours is not. It pops up whenever there is a steep drop from the set temperature, such as when you fill/refill your spa. No need to call a tech—just let the heater do its job and the water will reach its set temperature.
What does BLB mean on a water heater?
blb/BLB. If you see some variation of the letters BLB flashing across your control panel, it means that the UV bulb needs to be replaced.
Jacuzzi and the topside is flashing FL-1 code
Flashing FL-1 code and no HEAT on Jacuzzi (DIY) Step by Step how to FIX. Arizona Hot Tub Factory
Jacuzzi is Not Heating... FL-1 or FL-2 Flashing ...Circulation Pump Replacement. DIY Spa Repair
Jacuzzi is Not Heating... FL-1 or FL-2 Flashing ...Circulation Pump Replacement. DIY Spa Repair
Dynasty Spas... Heater Replacement...Gecko Control Pack.. DIY Heater Replacement
Dynasty Spas with Gecko Spa Pack.. Heater Replacement ...This is a very simple change out,, It took me longer to film then it did to replace the heater and you only need Philip screw driver and Cordless Screw drover to remove and replace the siding..I hope this video has enough detail to make your job go smoothly..
Myth-Busting...Does SIZE Really Matter ? (Jacuzzi J-355 VS. Jacuzzi J-325) Arizona Hot Tub Factory
Myth-Busting...Does Size Really Matter in a Hot Tub or Spa that is ? This was just a simple experiment will the water in a larger spa fill a smaller spa without over filling and spilling over. The answer is simple.....It's an Optical Illusion and most if not all viewers that watch this video would of never guessed the outcome.
When did Jacuzzi start making hot tubs?
The family behind Jacuzzi® Hot Tubs & Spas first made an aerating pump for hydrotherapy in the 1950s , and they began manufacturing hot tubs two decades later. By the ‘90s, these hot tubs had expanded into backyard models, and the award-winning company spread out into the international market by the year 2000.
Where is Jacuzzi located?
Their models feature eco-friendly and advanced hydrotherapy options, and Jacuzzi® Hot Tubs & Spas is headquartered in Chino, California.
What does it mean when a spa is in economy mode?
This only occurs when spa is in Economy mode and indicates a cool condition where temps have dropped 20°F (11°C) below current settings for them. System activates the heater and jets pump 1 to bring temp within 15°F (8°C) of settemps.