Receiving Helpdesk

what does er1 mean on a traeger grill

by Dr. Keegan Lockman Published 3 years ago Updated 3 years ago

Err and Er1
The reason you're getting an Err or an Er1 message is because there is a bad connection, or a complete disconnect, between the RTD probe and the control panel. Resolution. Ensure that the connections look good.

Full Answer

What does ER2 mean on a Traeger Grill?

Traeger Error Code Er2. If you saw such an error code on a display of your grill, it means there is a short circuit in it. You need to shut power off and call for a technician to insulate all the wires and make all the connections secure. Sometimes, this error code means there is weak connection in a smoker. Traeger Troubleshooting

What does error code 1 mean on Traeger?

Traeger Error Code 1 If you have seen this number of a code on the screen of your grill. It is very likely that you have got bad connection on your RTD. So, the digital display shows you the cause of a problem, but it doesn’t always show it.

What does ler mean on a Traeger Grill?

The low-temperature error code (LEr) is triggered when the temperature in the grill has dropped below 125°F for more than 10 minutes. This error code is the most common to pop up on a Traeger’s digital display. Follow these steps in order to resolve the LEr error code on a Traeger:

How do I Fix an ER1 error on my Grill?

The reason you're getting an Err or an Er1 message is because there is a bad connection, or a complete disconnect, between the RTD probe and the control panel. Ensure that the connections look good. Check the RTD connection by following these steps: Unplug the grill and remove the two Phillips head screws holding the controller in place.

Why does my smoker keep saying Erl?

When you find an Erl error message on your Pit Boss control board display, it usually implies that there's a problem with the inbuilt temperature sensor in the smoker. When the temperature probe is unable to make a connection and the controller determines that it can't read the probe, the Erl error code is displayed.

What does the error code HEr mean on a Traeger?

High Error ReadingA HEr error stands for “High Error Reading. '” This usually happens when the grill reaches over 550 degrees and shuts itself off. To understand why let's run through a few scenarios that could have caused this error.

How do you fix the Er1 code on a Pit Boss pellet grill?

2:306:32Fixing Pit Boss Error Codes! ErH, Er1, NoP, ErL #pitboss #pitbossnationYouTubeStart of suggested clipEnd of suggested clipNow to fix this you basically want to shut your smoker. Off and let it cool down. Once it's cooledMoreNow to fix this you basically want to shut your smoker. Off and let it cool down. Once it's cooled down you just want to make sure that the inside.

What does high temp error mean on Traeger?

A High Temp Error is specific to WiFIRE-enabled grills, and will occur when the grill's temperature reaches 550ºF/285ºC or higher for more than a few minutes. This is generally caused by excessive grease or ash buildup in the grill, or improper startup.

How do I fix the code on my Traeger?

0:423:27TRAEGER TROUBLESHOOTING How to fix "LEr" Error CodeYouTubeStart of suggested clipEnd of suggested clipSo step one is check your fire pot. And make sure it's clean and not overloaded with pellets. TheMoreSo step one is check your fire pot. And make sure it's clean and not overloaded with pellets. The second thing that can be wrong is your heat your sensor. Or your grill can just be too cold.

How do I clear my Traeger high temp error?

High Temp ErrorClean out the firepot > Place 5-10 pellets back into the firepot > Restart Grill.D2 grills require a "closed-lid start up," meaning you should start your grill with the lid shut. Failure to do so will often result in temperature irregularities through the duration of your cook.

How do you clean a temperature sensor?

0:312:59How to clean RTD probe/temperature sensor on pellet smoker - YouTubeYouTubeStart of suggested clipEnd of suggested clipBut when you pull everything out first thing you do is put that paper towel around that rtd pro soakMoreBut when you pull everything out first thing you do is put that paper towel around that rtd pro soak it down with the oven cleaner.

What does ERL mean on a thermometer?

The error message "Er.L" indicates that the current temperature in the operating environment is too. low (below 10°C).

How do I reset my Pit Boss?

A Pit Boss err code is best resolved by unplugging your grill and then restarting everything from scratch. Before you reconnect it to the power socket, check out the temperature sensor and wipe it down. An ErH means there is an issue with the heat and temperature control.

How do I reset my Traeger?

For a soft reset, power off your smartphone or tablet with the Traeger app. Wait a few minutes, then turn the phone back on. Then, power off the grill by switching the power switch off. Wait 30 seconds and then turn the grill back on using the same switch.5 Steps to Reset Traeger WiFIRE - Smart Home Starterhttps://smarthomestarter.com › 5-steps-to-reset-traeger-wif...https://smarthomestarter.com › 5-steps-to-reset-traeger-wif...

How do I calibrate my Traeger thermostat?

1:323:09How to Calibrate the Traeger Temperature Probe - YouTubeYouTubeStart of suggested clipEnd of suggested clipThat. There you go pro calibration. Hit that calibrate probe hit that there's your instructionsMoreThat. There you go pro calibration. Hit that calibrate probe hit that there's your instructions place it in a ice bath for one minute then press calibrate so we're gonna take a probe.How to Calibrate the Traeger Temperature Probe - YouTubehttps://www.youtube.com › watchhttps://www.youtube.com › watch

Why does my Traeger say low temp error?

A Low Error Reading of LEr, is an error message you may see on an AC platform Grills (non-WiFIRE enabled) except the 2017 AC Timberline 850/1300. Getting this message means that your grill dropped below 125 degrees for more than 10 minutes and caused the grill to shut off.LEr: Low Error Reading Message - Traeger Grillshttps://www.traeger.com › support › lerhttps://www.traeger.com › support › ler

Why does a fire go out in the middle of a traeger?

Fire Goes Out in the Middle of a Cook. There are several possible reasons for a fire to go out in a Traeger. Once again, we have to check the fire pot to see if the air holes are blocked. Fire needs oxygen to burn, and without those holes, there’s no oxygen. This is another time where the pellets may be the problem.

How hot is a traeger pellet grill?

Unusual Temperature Swings. It is totally normal for the temperature inside your Traeger pellet grill to vary by as much as 15-20F above or below the target you’ve set. That’s all part of the regular cycling on and off of the auger and the rod. When it cools down inside, more pellets feed in and ignite.

How to get rid of pellets on a grill?

Power off the grill and let it rest and then clear any pellets from the fire pot. You’ll need to start the grill up yourself once you’re ready to fire it up again. This code is bad news and could signal the demise of your meat unless you act quickly to control the heat or remove the meat from the grill.

Why is my traeger not getting up to temperature?

The simplest explanation is that you’ve run out of pellets, so there’s nothing to burn. It may be that the outside temperature is so cold your Traeger can’t get up to temperature. There may be debris that’s plugging your fire pot and preventing ventilation (you need oxygen for a fire).

What is an automatic auger?

The automatic, rotating auger is supposed to pull pellets from the hopper to the fire pot when the controller says they’re needed . It’s an amazing system – unless it’s not working.

How long does it take for a grill to cool down?

Once the temperature falls below 450F, the auger will run for 2 minutes to clear any embers from the auger tube. Power off the grill and let it rest and then clear any pellets from the fire pot.

How to fix a ignitor on a grill?

The most likely answer here is the ignitor isn’t working. Try running the grill with no pellets, and remove the heat diffuser, the drip pan, and the grates so you can see right into the fire pot. The tip of the ignitor should glow red. If not, there’s your issue.

What Does Mean Er1 Error Code on Z Grill?

Z grill error code Er1 is an error code of pellet grill smoker, which refers to the failure of the temperature sensor.

Reasons for Z Grill Er1 Error

Before finding the solutions for the problem, you should know why the Z grill error code Er1 is.

Solutions for Z grill Er1 Error

As you have been through this far, you have an idea about the Z grill error code Er1 and the possible reasons that cause the error to happen.

Final Thoughts

Now, if you have come this far, you should solve the Z grill error code Er1 without any issues.

What does ERR mean on a traeger grill?

So, the digital display shows you the cause of a problem, but it doesn’t always show it. The abbreviation ERR on the screen may mean that there must be malfunction of the RTD probe. Anyway, if you see some error code on a display of your Traeger, you will be able to understand what is going on. But, of course, in most cases you had better consult a professional and refer to the repair service. Maybe, you need some part to be replaced by a pro and the grill will work as it did before.

What does it mean when your grill is on?

If you saw such an error code on a display of your grill, it means there is a short circuit in it. You need to shut power off and call for a technician to insulate all the wires and make all the connections secure. Sometimes, this error code means there is weak connection in a smoker.

What to do if your grilling probe fails?

If your probe failed to work, it’s quite easy to replace it for a new one and your sensors will work in an excellent way while reading the temperature and controlling it during the grilling process.

Can you turn up the temperature on a grill?

In this case you should turn up the temperature set for your grilling and it will be fine. But if the weather is okay, there are the following steps you should do for checking: Check the fire pot for dust, make sure your grill is clean as it might be a cause of your low temp. There might be problems with a heat sensor.

LEr Code on Traeger

The LEr code on Traeger grills stands for “Low Error Reading”. When you see this message it means your grill automatically shut off because its temperature dropped below 125 degrees for more than 10 minutes. Your grill’s Fire Pit, RTD Sensor, or P-setting are most likely to blame for this error.

Traeger warranty

If none of the above fixes resolved your LEr code issue, you should look into your Traeger service and warranty agreement.

Conclusion

LEr code on Traeger means that the internal temperature dropped below 125 degrees for more than 10 minutes and the grill shut off as a result.

image

Ler – Low Temperature Below 125°F

Image
The low-temperature error code (LEr) is triggered when the temperature in the grill has dropped below 125°F for more than 10 minutes. This error code is the most common to pop up on a Traeger’s digital display. Common causes for the LEr error code are: 1. Traeger ran out of pellets 2. Firepot full of ash 3. RTD temperature pr…
See more on catchgrowcook.com

Her – High Temperature Over 550°F

  • The high-temperature error code (HEr) is triggered when the temperature in the grill reaches over 550°F. The grill will shut off and the fan will remain on to try to cool down the grill and burn off any remaining pellets. Common causes for the HEr error code are: 1. Dirty grill 2. Excessive grease on the drip tray 3. A fire or grease fire 4. Improper startup causing pellet buildup in firepot 5. Improp…
See more on catchgrowcook.com

Err

  • The ERR error code is generated when there is a bad connection or complete disconnect between the RTD temperature probe and the control panel. This means the computer cannot sense how hot or cold the grill is.
See more on catchgrowcook.com

ER1

  • The ER1 error code is generated when there is a bad connection or complete disconnect between the RTD probe and the control panel. This means the computer cannot sense how hot or cold the grill is.
See more on catchgrowcook.com

ER2

  • The ER2 error code is generated when the RTD probe has failed. However, the controller may also be the source of the failure since the ER2 code is created when the controller does not receive any temperature inputs.
See more on catchgrowcook.com

Frequently Asked Questions

  • Q: Where is the RTD temperature sensor?
    A:The RTD temperature sensor is the upright metal probe located on the left-hand side of the grill when the lid is opened. The sensor will either be shiny silver or black depending on how often the smoker has been used.
  • Q: How do I restart a Traeger that ran out of pellets?
    A: Follow this step-by-step photo guidethat walks you through how to correctly restart a Traeger that ran out of pellets.
See more on catchgrowcook.com

Final Thoughts

  • Error codes are simply a way for the Traeger to notify you of an issue that’s occurred. Thankfully most common error codes on a Traeger are relatively easy to resolve and won’t cost you a thing. Traegers are fantastic pellet grills that work for hours on end without needing a thing. However, these pellet grills do need to be maintained and cleaned so that they can continue to work prope…
See more on catchgrowcook.com

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 1 2 3 4 5 6 7 8 9