what are pending fault codes

What are pending fault codes? Pending codes are caused by intermittent faults or faults that the PCM needs to see happen in two consecutive warm-up cycles to set the code. If the fault does not reappear within 40 warm-up cycles, the code will be cleared from memory.

Full Answer

What does it mean when a trouble code is pending?

Trouble codes which have both Pending and Hard status are referred to as two-trip trouble codes. This means the computer has to run a specific test twice before it determines a true fault exists; and before it turns on the check engine light, alerting the driver of an emissions problem.

What does pending code mean on OBD 2 emissions?

Pending codes mean that the OBD-II monitoring system has failed the operation of an emission control system at least once and if it fails again the Check Engine Light will be turned on and the malfunction becomes an Active code. Likewise, will a pending code fail emissions?

Why does my car have a pending code but no warning?

The end result is the car surges and miss fires for a second or two which causes a pending code. You normally won’t notice a warning indicator or light come on. This is because since it happened just once and so briefly, the computer doesn’t detect any problems and therefore displays no codes.

What is the difference between active code and pending code?

Pending Code: The system or component have not failed two or more times for the ECM/PCM to set the Engine Light. Active Code: The system or component do not require failure two or more times to set the Engine Light, or the system or component have failed two or more times.

How long do Pending OBD codes last?

Will a pending code fail emissions?

What are confirmed trouble codes?

Do stored codes clear themselves?

Can you pass NYS inspection with a pending code?

Can you pass emissions with a permanent code?

How do I read a diagnostic trouble code?

Where can I read car codes for free?

What is a pending misfire?

Is EVAP code serious?

How far do you have to drive to reset the check engine light?

What does a permanent check engine code mean?

What is the difference between pending and stored codes?

For a quick answer though, the difference between stored and pending codes is simple. Stored codes are put in place from the manufacturer to signal the computer when a common fault is detected. Pending codes are codes that prep themselves when they determine a fault that engine cycle. Pending codes can be just a quick flash with no symptoms ...

Why are stored codes more complicated than pending codes?

Stored codes are a little more complicated than pending codes. These codes are there either from the factory for legal purposes and safety precautions or because a malfunction has been detected.

What is the error code for a catalytic converter?

This would mean that all the auto manufacturers use pretty much the same “error code” for many of the same symptoms. As an example, the term P0420 usually means a catalytic converter problem.

What does P0420 mean?

As an example, the term P0420 usually means a catalytic converter problem. This code however is ran across many different makers like Chevy, Ford, Dodge, etc… all of these vehicles will share that same code for a catalytic problem.

What does it mean when the gas cap blinks?

If it starts blinking, turn over immediately as this is a critical error code. This means something went completely wrong during the operation of that engine.

Why won't my computer detect a warning light?

This is because since it happened just once and so briefly, the computer doesn’t detect any problems and therefore displays no codes. These are basically a “preventative maintenance” type of code.

Can you clear codes yourself?

You can clear codes either by fixing them or by getting them repaired by a shop and having them clear the codes . It is illegal in some areas to clear codes yourself, you have been warned. That pretty much sums up the difference between stored and pending codes in your car.

Can a pending trouble code cause a vehicle to fail a smog test?

Answer: A pending trouble code should not cause your vehicle to fail the smog check. The smog test process (for 2000 & newer vehicles) relies on your vehicle's computer having determined an emission fault being present or not; this being indicated by an illuminated (ON) check engine light or malfunction indicator lamp.

Does pending go away when you reset your MIL code?

When I reset my codes, the pending goes away too. Yes, if you clear a MIL (check engine light) all readiness codes clear. They only run and complete under certain conditions which is why sometimes it can take a day or 2-3 to pass them or enough of them to run through emissions. Click to see full answer. Likewise, what does it mean ...

What is a two trip trouble code?

Trouble codes which have both Pending and Hard status are referred to as two-trip trouble codes. This means the computer has to run a specific test twice before it determines a true fault exists; and before it turns on the check engine light, alerting the driver of an emissions problem.

Why does my engine light not turn on?

Pending trouble codes do not turn on the check engine light because the engine control computer has not yet determined, for certain, that the engine has a fault. The computer has noticed a "possible" problem with the emissions system but needs to gather further data before being certain.

Can a pending trouble code cause a vehicle to fail a smog test?

A pending trouble code should not cause your vehicle to fail the smog check. We say "should" because smog technicians have reported, and for unknown reasons, that they've had vehicles fail the smog test with only a pending trouble code (s). This is not the norm and 99.9% of the time a vehicle passes the smog test with a pending OBDII trouble code ...