washing machine error code list

Washer Error Codes:

• • E16 or F16: Door is open. Find more about it here.
• • E18 or F18: Pump time has exceeded its limits. Find more about it here.
• • E19 or F19: Heating time has been exceeded. Find more about it here.
• • E20 or F20: Unexpected heating in your washing machine. Find more about it here.

Full Answer

What do the codes on my washing machine mean?

• Whirlpool WTW6400SW0
• Whirlpool WTW6400SW1
• Whirlpool WTW6400SW2

How to fix e1f3 error code in front load washer.?

Switch off the device and unplug it from the socket for a few minutes. Restart it and see whether the error code is still indicated on the display. If no — lucky you, it was just a system glitch and now you can start your washing process.

How to fix Whirlpool washer F23 error code?

• Unplug the whirlpool washer from the power source
• Next take off the washer top
• You will see a couple of screws at the back side
• Remove the screws, slide the top back and it should come off easily.
• Next, check the wiring that leads to the door lock from the central control unit to the door lock.
• If the wiring is ok, the plugs should be seated properly.

More items...

How to fix Le error code on LG washing machine?

LG front-load washer LE error code

• Overloaded washer. Make sure the washer isn’t overloaded. ...
• Too much detergent. If you see lots of suds in the tub, let the washer sit idle for 30 minutes so the foam dissipates. ...
• Drive system obstruction. If you didn’t overload the washer and you don’t see excessive suds, check the rotation of the spin basket.
• Loose wiring or defective drive motor. ...

What are washing machine error codes?

Error Codes in my Whirlpool Front Load WasherError CodeErrorrL or F34Items were detected in the washer during the Clean Washer cycle.Sud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,7 more rows•Apr 11, 2022

How do you read a washing machine code?

1:092:21How to Read a Vertical Modular Washer (VMW) Error Code DisplayYouTubeStart of suggested clipEnd of suggested clipTurn the control dial one click clockwise. Press. The start button turn the control dial one clickMoreTurn the control dial one click clockwise. Press. The start button turn the control dial one click clockwise to display the first saved error code. The control displays up to four error codes.

How do I reset my washing machine after error code?

If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.

What are the common faults of washing machine?

10 Most Common Washing Machine ProblemsIt Bounces Around. ... It's Noisy. ... Clothes Are Getting Ripped. ... Improper Or Slow Draining. ... My Washing Machine Won't Spin. ... There's No Water. ... The Door Won't Open. ... It's Smelly.More items...

What do washing machine symbols mean?

A circle inside a square means you can tumble dry the garment. The dots indicate temperature – one for low heat, two for slightly higher heat, and three for high heat. A cross over the symbol means you shouldn't tumble dry the garment.

What do laundry symbols mean?

A laundry symbol, also called a care symbol, is a pictogram indicating the manufacturer's suggestions as to methods of washing, drying, dry-cleaning and ironing clothing. Such symbols are written on labels, known as care labels or care tags, attached to clothing to indicate how a particular item should best be cleaned.

How do you troubleshoot a washing machine problem?

Washer Troubleshooting GuideCheck that the washer is plugged in securely.Check the circuit breaker or fuse box.Test the outlet for current.Check that the water supply valves are turned on.Inspect the filter screens.Test for overheating.Test the water level switch.Test the timer control.More items...

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.

How do you restart a washing machine?

1:173:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.

Why is my washing machine beeping?

Washer sounds and beeps Your machine is checking that the water has drained before spinning. Your washer will beep if you have used 'No Spin' and at the end of the cycle. If your machine is beeping continuously or giving a musical series of beeps, refer to the 'Before you call for service' section.

What causes a washing machine not to drain?

Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed. Whatever the reason, the water will need to be drained from the washing machine before any work or diagnosis can be done.

What is the problem if the washing machine wont spin?

Normally, your washing machine won't go into a spin cycle until it's been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.

Why is my drain hose not draining?

Cause: not fully drained within 10 minutes. Check there isn’t a kink in your drain hose, ensure the filter is clean, the drain hose can become clogged with sludge, sometimes a hot wash with 1/2 a cup of vinegar will remove this sludge. “FE”. Over flow error.

Can fault codes vary?

Fault codes can and do vary from manufacturer to manufacturer, even between models from the same manufacturer these codes may well be different . This guide is designed only as a generalized guide and is not intended to replace your owners manual, if you have problems always check the owners manual first, it may well have ...

How to fix a clogged water hose?

1. Check the inlet hose that connects your machine to the tap. 2. Remove any clog or kink inside it and wash it thoroughly. 3. If the problem persists, replace the hose. OE. The issue in draining the water out. 1.

Can washing machines identify faults?

The Washing machines from popular brands have become quite smart, thanks to the advancement in their technology. These machines can now identify any fault in any part of the system and display the relevant error code on the screen . These error or fault codes vary from one brand to another.

How many cycles does a washer have?

The washer has run 30 wash cycles and is indicating a reminder to run the Clean Washer with affresh cycle. Run the Clean Washer with affresh cycle. If the Clean Washer with afresh cycle is not turned on, the LED will stop flashing at the end of a wash cycle after running 3 more regular wash cycles.

What is the function of a Whirlpool washer?

All users of Whirlpool washers are informed about a very useful function – the electronic self-diagnosis system. That means that in the case of failure machine determines a breakage and displays information in a form of the code. With the help of this option, you can cope with a problem by yourself without calling a repair service.

drn Error Code

Condition: The washer is not draining properly. This error code means that the machine might stay filled partially or all the way up with water in the basin of the washer.

PF Error Code

Condition: Power failure interrupted the washing cycle. Parts where possible failure may take place: Washing machine, motherboard.

LOC or LC Error Codes

Condition: The control lock is activated. Parts where possible failure may take place: The locking mechanism on the lid.

rL or F34 Error Codes

Condition: Items were detected in the washing machine during the clean washer cycle.

F9 E1 Error Code

Condition: Draining water is taking too long (usually more than eight minutes).

How to fix a washer that is overloaded?

The washer has attempted to fill and begin the wash cycle. If the washer is overloaded, it will drain any water and detergent that was added during the fill. To correct the overload, remove several items and add detergent. Close lid and press START.

Is Kenmore a household appliance?

The Kenmore company has been producing household appliances for 90 years. Its goods are well-known in the USA and outside the country. Washers have proven themselves as a quality, multifunctional and durable equipment. But even the most reliable technique could break down.