Check out this video to learn how to run a diagnostic test on your Samsung washer. Codes: 1E, LE, LE1, 1C, LC, LC1, 1 1C, 1 LC, E7, E9, 11E – Water Level Error or Leakage These codes signal that there’s either an issue with the water level sensor, a low water level, or a leak.
What are the problems with Samsung washers?
Why Samsung Washing machine Won’t Spin
- SuspensionWorn Out. ...
- Shock Absorbers (Front Loading Machine Only) There are four shock absorbers that hold the plastic drum and compensate for all vibrations coming from the drum during the spin cycle.
- Faulty Door Lock (Samsung top load washer problems spin cycle) The Samsung washers have a door lock with a switch. ...
- Broken Plastic Bracket. ...
How to run calibration mode on Samsung washers?
- Remove laundry or any contents in the machine.
- Press and hold Water Level and Delay End simultaneously for at least 3 seconds when the power is turned on.
- Press Start/Pause to activate Calibration Mode.
- The pulsator will rotate clockwise and counterclockwise approximately 1 minute.
Why is my Samsung washer not spinning?
Troubleshooting and Diagnosis
- Faulty Suspension. Maybe you’ve spent the last 20 minutes trying to get your Samsung washing machine to start up and spin, only to end up with a UE, UL, or ...
- Worn Out Shock Absorber. It’s no secret that washers and dryers take a beating. ...
- Door Lock Motor and Switch Assembly. ...
- Loose Drum Nut. ...
- Faulty Drain Pump. ...
- Broken Plastic Bracket. ...
- Use HE Detergent. ...
How to do spin only on Samsung washer?
- Power the unit on.
- Press and hold the spin key for approximately 3 seconds. A chime will sound.
- Select the spin level, if desired.
- Press the Start/Pause button.
How do I put my Samsung washer in test mode?
Postion 5 on the control dial SPn is for testing the motor on varied spinpress start to start motor test.you will see motor increase in the display.will keep increasing.when it reaches maximum spin speed press start again to stop cycle.
What are Samsung washer codes?
Samsung Front-Load Washer Error CodesFault CodeWasher ProblemLELow water level during cyclesOEOverflow or too high water levelsnF1Hot and cold water lines are reversedtEWater temperature is either too high or too low13 more rows•Apr 14, 2022
How do you put a washing machine in self test diagnostic mode?
0:000:48Whirlpool Washer Test/Diagnostic Mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou press the start button this will allow your washing machine to go into the test or diagnosticMoreYou press the start button this will allow your washing machine to go into the test or diagnostic mode and this will isolate if you're having any issues the water will run the spin cycle will engage.
How do I reset my Samsung washing machine?
Resetting your washing machine is a simple procedure. Unplug it (or turn off the power at the circuit breaker), wait a short period of time for the electrical charge to dissipate from the washer (typically 1 to 5 minutes at the most), and then plug it back into the wall. That's all there is to it.
What are washing machine error codes?
Error Codes in my Whirlpool Front Load WasherError CodeErrorrL or F34Items were detected in the washer during the Clean Washer cycle.Sud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,7 more rows•Apr 11, 2022
How do I troubleshoot my Samsung front load washer?
SAMSUNG WASHER FIX/SOLUTION:Check the fuse or reset the circuit breaker.Straighten the drain hoses.Eliminate kinked hoses.If there is a drain restriction, troubleshoot it.Close the door and press the Start/Pause button.For your safety, your washer will not tumble or spin unless the door is closed.More items...•
How do I put my LG washer in diagnostic mode?
Press the POWER to turn on the washer. Place the mouthpiece of your phone between the Smart Diagnosis logo and the POWER button. After pressing the Start Diagnosis button, press and hold the TEMP button until a countdown displays on the washer.
How do I put my Whirlpool front load washer in diagnostic mode?
0:132:03Whirlpool Duet Washer Diagnostics & Error Codes - YouTubeYouTubeStart of suggested clipEnd of suggested clipChoose any three buttons except for power or start and press them in sequence. One. Two three oneMoreChoose any three buttons except for power or start and press them in sequence. One. Two three one two three one two three. If you got it right you'll know the duet washer has three diagnostic modes.
How do I find the error code on my Whirlpool washer?
0:256:06How to put a Whirlpool washer on the fault code display mode - YouTubeYouTubeStart of suggested clipEnd of suggested clipStart with the cycle selector knob in this position. Next you need to turn the cycle selector notMoreStart with the cycle selector knob in this position. Next you need to turn the cycle selector not the way that I'm going to show you one click to the left three clicks to the right.
Why does my FlexWash machine have a 1DC4 code?
If you have a FlexWash machine, the 1dC4 code signals that the rubber button by the latch is missing. In this scenario, you simply need to replace the button.
How long does it take for a washer to calibrate?
Your washer detects the weight of items in the drum to determine how much water to use. Calibration mode usually lasts about one to three minutes and stops by itself.
What does dc3 mean on a washer?
Any of these codes can represent a problem with the main door of your washer, except dC3. dC3 represents an issue with the add-door. This is the small, extra door located in the washer’s main door. In some cases, dC can also signal an issue with the add-door.
Why is my washing machine off balance?
Your machine can be unbalanced due to being over or under-filled, or when you are washing very bulky items. The UR code means that your machine will attempt to add water to balance the load and try again.
Why was Samsung washing machine recalled?
In 2016, Samsung issued a recall of 2.8 million top-loading washing machines made between March 2011 and April 2016 because the top can unexpectedly detach while in use, posing a risk of injury from impact, according to the United States Consumer Product Safety Commission . A complete list of recalled models can be found on the commission website.
Why does my washer smell?
Too many suds. Using a regular detergent or even too much high-efficiency detergent can produce excessive suds. This extends the length of the cycle, leaves your clothes sticky and soiled from redeposited dirt, and can make your washer smell . Allow the suds to settle, and move to the spin cycle.
How long does it take for a washer to fill?
If the washer takes 40 minutes or more to fill or if the water level doesn't change after six minutes, the nF code will appear. Check that the water supply faucets behind the washer are fully open and kink free. The lines can also freeze if the washer is exposed to low temperatures.
What happens if you force the washer door open?
Forcing the door open might damage the door lock/switch, which is often made of plastic. However, it is simple to replace and much less expensive than calling a technician. ds. Door is not locked. If the washer won't start, the ds code might appear, signaling that the washer door is open and the lock is malfunctioning.
Why is my washer overfilled?
A washer that is overfilled is usually caused by water inlet valves that are not shutting off the water flow properly. Replace the water inlet valve assembly. nF1. Hot and cold water lines are reversed. Connect the hot and cold water fill hoses correctly on the back of the washer.
Starting the testing process
Understanding how to conduct a self-diagnosis of the unit will help testing a Samsung automatic machine of the popular Eco Bubble line. The principle of the described actions will be similar for most other brand models. Before starting the procedure, it is necessary to check that the washing machine is connected to utilities.
Linear Testing
The service test of the Samsung machine is conventionally divided into two stages, and the first of them is the verification of the linear components of the machine. It allows you to visually verify the sufficient performance of linear components, such as:
Checking sensors and motor
The performance test of various sensors and the SMA motor is performed by rotating the knob of the washing program. By setting the selector to a specific mode, you can diagnose a separate part of the device. Let’s tell you where you should direct the handle to test the motor, temperature sensor, level sensor, main power board.