Samsung Top Load Washer activewash error codes
| Information Code | Meaning |
| AC6 | Communication error (Inverter PBA - MAIN ... |
| 8C/8C2 | MEMS sensor problem |
| 4C2 | This occurs when the temperature exceeds ... |
| PC | When position of the clutch can’t be det ... |
How do I check the MEMS sensor on my Samsung washer?
0:232:14How to replace Samsung washer vibration sensor part #DC93-00278EYouTubeStart of suggested clipEnd of suggested clipNow untwist the wire tie. Then disconnect the electrical plug by depressing the locking tab. NowMoreNow untwist the wire tie. Then disconnect the electrical plug by depressing the locking tab. Now remove the two Phillips screws and pull the sensor. Off. If you have a bad member.
What does the code for C mean on a Samsung washer?
The 4E (4C) error code indicates that the washing machine has detected a problem with the water supply. The most common reason for this error is a blocked or kinked water supply hose.
What does a MEMS sensor do on a Samsung washer?
The MEMS sensor is basically a vibration sensor to control board that the machine is experiencing and out-of balance condition.16-Nov-2021
How do I fix my Samsung 8e washer?
If there is a temporary malfunction in the washing machine, reset the device by turning it off for 5 minutes from the mains. Then, turn the appliance on again. The 8e error code or a similar one should disappear. In case of the vibration sensor burning out, replace it with a new one.
How do I fix 5E error on Samsung top load washer?
Resolve 5E Error Code on your Samsung Washing Machine Turn off the washer and check that it is level. ... Inspect the drain hose. ... Clean the pump filter (for front load only*). ... Turn the washer back on and start a cycle. ... Request service.
How do I fix my Samsung 4C top load washer?
Step One – Check the Water Taps. The first step is to check if both the hot- and cold-water taps are turned on correctly. ... Step Two – Check the Water Hoses. ... Step Three – Check the Mesh Filters. ... Step Four – Clean the Detergent Tray. ... Step Five – Check the Water Pressure. ... Step Six – Reset Your Washer.02-Aug-2021
How do you fix an unbalanced Samsung washer?
2:277:08Samsung Top Load Washer Off Balance FIX DIY How to ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipYou're going to bring the suspension rod down a little bit. And then you're going to remove. It toMoreYou're going to bring the suspension rod down a little bit. And then you're going to remove. It to get the new rod in you simply just slide it. In between the hooks. And then pull up. And then pull.
How do I put my Samsung washer in diagnostic mode?
1:297:26Samsung Front Load Washer Error Codes and Test ModeYouTubeStart of suggested clipEnd of suggested clipFirst power on the machine. Once it is fully powered on press and hold the delay. Start button asMoreFirst power on the machine. Once it is fully powered on press and hold the delay. Start button as well as the soil. Level button as circled. If you press them simultaneously.
How do you reset a Samsung washer?
Reset your washing machine What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a "reset" of the washer.
What does 8E mean on a Samsung refrigerator?
8E: Ice Maker (Freezer) Sensor Error.
What does E8 in a washing machine mean?
Question: Error Code-control panel display "E8" Answer: Reason:Water protection level error. Solution:Auto release. Otherwise if the error is still exist, please unplug the machine and turn the water tap off, then call for service.15-Feb-2015
Internal Failure of The MEMS Sensor
- In the Samsung washer, the 8C error code is displayed when the accelerometer is “silent” or gives incorrect/ weak signals to the control module. It can be tested through the DC92-01624A board. VRT+ is connected to the PCB of the display. The PCB-Sub itself has a 6-wire 15P connector. Namely, it is needed for checking the sensor. 1. Switch on the washing machine. 2. Attach the bl…
Broken Contacts
- Error code 8C can be displayed when VRT+ is not connected to the module. Inspect the terminals of the MEMS sensor connector and the P8 CN8 electrical connector. If everything is in order, check the integrity of the wiring that goes to the accelerometer from the main unit. She often breaks off under the screed. An open circuit in the electrical circuit needs to be repaired: clean a…
Control Board Failure
- If during testing 15P on PCB-Sub the red wire of pin 1 does not show 3.3 V DC, then the electronic controller is the reason. It sends or receives information incorrectly, wherefore 8C error appears. The tracks can be repaired, burnt elements can be replaced. But if the processor breaks down, you will have to install a new PBA DC92-01021V printed-wiring board. It costs from $ 170.
Problems with The Motor and Its Elements
- Sometimes 8C error code occurs in Samsung washer immediately after filling with water, and the drum does not rotate on all programs. This indicates the breaking of the motor winding. It should be completely replaced. If the equipment fails to gain speed at the beginning of spinning, check the motor brushes. They can create an inhomogeneous magnetic field, wherefore the MEMS se…
The Weak Connection Between The Accelerometer and The Electric Motor
- VRT+ is fixed to the motor case with fasteners that can untwist. In this case, in the washing mode, the drum does not rotate correctly and stops during the spin cycle. Check and tighten the mounts. Sometimes the connection is lost due to oxidation/polluting of the motor shaft or magnetic ring. As a result, the vibration sensor gives false signals, the control acts only at low speeds. Spinnin…