How do I run diagnostics on my Samsung top load washer?
2:0916:13How to Find Samsung Washer Codes and Use Diagnostic ... - YouTubeYouTubeStart of suggested clipEnd of suggested clipAll we need to do is press the spin. Button. And then that's going to take us to error codes.MoreAll we need to do is press the spin. Button. And then that's going to take us to error codes.
What are the codes for a Samsung top load washer?
Samsung top-load washer error codesDS, FL or LO. Lid lock/switch failure. Check/ ... HE1. Heating element failure. Check/ ... LE. Water leakage. Check/ ... OE. Water overflow. Check/ ... tE1. Temperature too high or low. Check/ ... dc. Unbalanced load. Check/ Repair. ... PE or PE1. Clutch motor failure. Check/ Repair. ... Sud or Sd. Excessive suds. Check/ Repair.More items...
What is diagnostic mode on washing machine?
The washer's diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.
How do you reset a Samsung washer?
How to reset Samsung washing machine eco bubble (steps)Step 1: Turn on the washing machine. You clearly simply need to press the power button to make it turn on.Step 2: Press the option button. Next, press the option button on the machine for about 5 seconds. ... Step 3: Turn the dial to factory reset. ... Step 4: Tap to reset.
What are washing machine error codes?
Error Codes in my Whirlpool Front Load WasherError CodeErrorrL or F34Items were detected in the washer during the Clean Washer cycle.Sud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,7 more rows•Apr 11, 2022
How do I fix my Samsung washer error?
On your Samsung washer, the "dE" error code typically occurs just after the rinse cycle. This will leave your machine filled with water as it does not drain because the washer thinks that the lid is open. Reset the cycle to properly drain the water then stop it before it fills up again.
How do you diagnose washer control and program problems?
0:129:07How to Diagnose Washing Machine Control and Program ProblemsYouTubeStart of suggested clipEnd of suggested clipBefore suspecting that the problem lies in the control board for example in the drainage circuit youMoreBefore suspecting that the problem lies in the control board for example in the drainage circuit you would check the drain pump and the wiring.
How do I put my Samsung washer in calibration mode?
How do I run Calibration Mode on my Samsung washing machine?1 Turn the washing machine off and then on again.2 Hold down the Temp and Delay End + buttons for 3 seconds until a CB code appears on-screen. ... 3 Press Start/Pause to run the Calibration cycle.More items...
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.
How do you reset an automatic washing machine?
1:243:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
Why is my Samsung top load washer not spinning?
If your washer isn't spinning properly , it could be because of an unbalanced load, which makes it harder for the drum to spin. An unblanced load also cause errors. "Ub" or "Ur" display is one of the sign that your washer is unbalanced. This may be because the washer is lopsided or because the load inside is uneven.
Why do Samsung washers have out of balance protection?
Today's washers have out of balance protection installed to protect a washer from damaging itself during the spin cycle. Some Samsung washers add more water during the spin cycle to attempt to correct the imbalance of a small load. To solve the problem of extra water, redistribute the clothes to better balance the washer.
Why is there a recall on Samsung washing machines?
There has been a recall on Samsung front load washers because water leakage onto the electrical connections of the washing machine's thermal sensor can cause an electrical short and ignite the circuit board , posing a fire hazard to consumers.
What happens if the washer is not level?
If the washer is not level and it is tilting to one side or forward or backward, the dispenser cups will not empty completely and you will get drips on the next load. After using the bleach dispenser, remove the dispenser cup and rinse it well or dry it with a paper towel to prevent drips.
Why does my washer have purple streaks?
Solution: The purple streaks happen when too much laundry detergent is used. One teaspoon of concentrated HE detergent is the recommended amount for a small, cold water load. Never use more than two teaspoons in a HE washer no matter the load size or water temperature.
Why does my washer leak water during the rinse cycle?
Solution: If a leak is going to happen with a front loader, it is most often during the rinse cycle because more water is used at that time.
How to clean a washer that is locked?
Solution: If the washer is receiving electrical power and everything else looks good, start by cleaning the contact points of the door latch with a bit of rubbing alcohol on a cotton swab. Even though it indicates that it is "locked", there must be full contact.
How to fix slow drain on washer?
To correct the slow drain, open the bottom panel of the washer housing. You will see a plug on the lower right. Have some towels ready to catch a gush of water and remove the plug. Clean out the filter. You may find lint, coins or buttons are obstructing the flow into the pump. Never overload the washer.
Request repair service
Arrange for a service visit at home, schedule a walk-in appointment or mail your device in for a repair.
Watch how-to videos
Watch our helpful videos to get the most out of your Samsung products.
Register your product
Gain access to exclusive offers and perks, apps and services, world-class customer support and more.
Starting the testing process
Understanding how to conduct a self-diagnosis of the unit will help testing a Samsung automatic machine of the popular Eco Bubble line. The principle of the described actions will be similar for most other brand models. Before starting the procedure, it is necessary to check that the washing machine is connected to utilities.
Linear Testing
The service test of the Samsung machine is conventionally divided into two stages, and the first of them is the verification of the linear components of the machine. It allows you to visually verify the sufficient performance of linear components, such as:
Checking sensors and motor
The performance test of various sensors and the SMA motor is performed by rotating the knob of the washing program. By setting the selector to a specific mode, you can diagnose a separate part of the device. Let’s tell you where you should direct the handle to test the motor, temperature sensor, level sensor, main power board.