23+ Common Samsung Front Load Washer Error Codes
- Error Code 1E This is caused by a Water level sensor Issue. The solution is to wait 30 seconds after turning off the appliance at the mains. ...
- Error Code 3E, 3E1, 3E2, 3E3, 3E4 This is caused by Motor Defects. To solve this, switch off the appliance at the mains then wait 30 seconds. ...
- Error code E4 This is caused by the Water supply error. ...
Full Answer
What is the best front loader washer?
- Best Washer Overall: LG 12-Cycle Front-Loading Smart Wi-Fi Washer
- Best Dryer Overall: Samsung Large Capacity Electric Dryer
- Best Stackable Washer And Dryer: LG Wash Tower
- Best Front Loading Washer And Dryer Set: Whirlpool High Efficiency Stackable Front Load Washer And Dryer
Does Samsung make good washers?
- Samsung - 4.2 Cu. Ft.
- Ft. 14-Cycle Front-Loading Washer - Black stainless steel.
- Ft. 12-Cycle Front-Loading Smart Wi-Fi Washer with Steam and 6Motion Technology - Graphite Steel.
- Ft. 12-Cycle Front-Loading Smart Wi-Fi Washer with Steam and 6Motion Technology - White.
- Whirlpool - Cabrio 4.3 Cu. Ft.
Is there a reliable front load washer?
Samsung front-load washers rank highest in customer satisfaction, according to J.D. Power's laundry appliance satisfaction study, and Samsung was named a most reliable brand by Yale Appliances and Puls repair technicians, as well.
How to disassembling Samsung washer front load?
- To complete the removal of the front panel, use a pair of needle nose pliers to remove a retaining wire that holds the door boot seal in place.
- Pull the seal away from the lip of the front panel.
- Remove two screws that secure the door latch assembly in place.
- Open and remove the filter access door and release the drain tube from the retaining tab.
What are washing machine error codes?
Error Codes in my Whirlpool Front Load WasherError CodeErrorrL or F34Items were detected in the washer during the Clean Washer cycle.Sud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,7 more rows•Apr 11, 2022
How do you clear error code on Samsung front load washer?
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a "reset" of the washer.
What are the codes on a Samsung front loader washer?
Samsung Front-Load Washer Error CodesFault CodeWasher ProblemLELow water level during cyclesOEOverflow or too high water levelsnF1Hot and cold water lines are reversedtEWater temperature is either too high or too low13 more rows•Apr 14, 2022
What are the Samsung washing machine error codes?
Samsung Washing Machine Error/Fault Codes5E/SE - Draining Problems. ... 4E – Not Enough Water Entering Machine. ... dE or DC – Open Door. ... UE – Unbalanced Load. ... 3E – Faulty motor tacho. ... bE - Motor triac short error. ... OE - Too much water in machine. ... LE – Water Leak.More items...
How do I run a diagnostic on my Samsung washing machine?
2:0912:58Samsung washing machine diagnostic mode How to check error ...YouTubeStart of suggested clipEnd of suggested clipButton one button two button three and the start pause button the temperature or button one controlsMoreButton one button two button three and the start pause button the temperature or button one controls the fill cycle and tests all the water valve.
Why is my Samsung Washer blinking?
2. Samsung washer spin light blinking. For the most part, this is due to improper installation of the washer or failing to balance the load. For that reason, work on balancing the load size (as explained earlier) and ensure the selected type of cycle matches what you're washing.
How do I reset my washing machine?
1:243:47Washer Not Spinning - How to Reset Motor (Easy) - YouTubeYouTubeStart of suggested clipEnd of suggested clipThe machine gives you 30 seconds to lift the lid and close. It six times and once you start liftingMoreThe machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
What are Samsung Washer Error Codes?
In a washing machine, an error code can represent a problem with the machine or it can signify a locked door or a locked detergent drawer. You may see an error code because of the following problems:
Why does my washer fan keep working?
These errors are caused by appliances too hot. This is not a fault; the appliance fan will continue to operate until the appliance is cold enough to remove the washing (55°C). The door will then be unlocked. – This prevents heater malfunctions.
Why is my phone not responding to my power button?
This is caused by a power Button issue. The remedy is to press the Button for an unusually long period of time. Check to see if any of the buttons are stuck or are jammed in place. Remove the device from the power supply and clean the buttons with a gently wet cloth.
What does it mean when your washing machine is overflowing?
The Overflow error. It’s possible that too much washing powder/liquid was used. The solution is to turn off the power to the appliance, wait 30 seconds, and then turn it back on. To drain the washing machine, turn on the drain pump.
Why is my washing machine water leaking?
The solution is to check that the level of the drain hose does not fall below the level of the washing machine’s base. In addition, look for a water leak. If there is no evidence of water, turn off the power, reconnect, and try again.
What cycle do you use to clean a washing machine?
The appliance will typically correct itself, but if it does not, you will need to run either an “Eco drum clean” cycle (on some models) or a 90°C cotton cycle with no detergent or washing load.
Why is my water hose not hot?
This is caused by a Water cooldown issue . The remedy is to check water hose is connected to a cold supply and not a hot supply. Coldwater is usually indicated by a blue tap.
Why is my Samsung washer flashing?
If your Samsung washer is flashing one of these codes, it signals a drainage problem. It could be that your machine is draining incorrectly or not at all.
What to do if you see a code on your washer?
If you see one of these codes, there’s something up with the electrical current going to the washing machine. Ensure your washer is plugged directly into an outlet and on its own circuit. Do not use an extension cord.
How long does it take for a washer to calibrate?
Your washer detects the weight of items in the drum to determine how much water to use. Calibration mode usually lasts about one to three minutes and stops by itself.
Why is my washing machine off balance?
Your machine can be unbalanced due to being over or under-filled, or when you are washing very bulky items. The UR code means that your machine will attempt to add water to balance the load and try again.
What does dc3 mean on a washer?
Any of these codes can represent a problem with the main door of your washer, except dC3. dC3 represents an issue with the add-door. This is the small, extra door located in the washer’s main door. In some cases, dC can also signal an issue with the add-door.
Why does my water hose come loose from the drum?
Verify that the water hose connected to the sensor is still connected. Sometimes, this hose can come loose from the drum due to vibration.
Why does my FlexWash machine have a 1DC4 code?
If you have a FlexWash machine, the 1dC4 code signals that the rubber button by the latch is missing. In this scenario, you simply need to replace the button.
What causes a washer to be unbalanced?
When loading your washer with clothes, make sure they are evenly spread out and there are not too many heavy items on the same side. A heavy sweater, coat or even jeans can cause the washer to become unbalanced and trigger an error code.
What to do if you are uncomfortable with your Samsung washing machine?
If you are uncomfortable working on your Samsung washing machine, you should call a certified technician to diagnose and repair the machine.
Can you see error code on Samsung washer?
Depending on the age of your washer, you may see a different error code. Unfortunately, when Samsung changes their appliance design and as technology improves, so do their error codes. This can make it difficult to sort out which error code you are seeing and the possible problem.
Who is Joanna Stewart?
Joanna Stewart is an experienced interior designer, construction management expert and DIY enthusiast. She enjoys helping homeowers get the most value out of their remodeling budgets.