Open the hood of the Ford. Loosen the lock nut located on the negative battery cable connector with a socket and ratchet. Pull the connector off the negative battery terminal. Step 2 Wait for 20 minutes while the PCM bleeds off the electricity it stores for backup power. Once the power drains from the PCM, it resets.
Full Answer
How to replace the Powertrain Control Module?
Symptoms of a Bad or Failing Engine Control Module (ECM)
- Check Engine Light Turns On. An illuminated Check Engine Light is one possible symptom of a problem with the ECM. ...
- Engine Stalling or Misfiring. Erratic engine behavior may also indicate a bad or failing ECM. ...
- Engine Performance Issues. Engine performance issues are another symptom of a possible problem with the ECM. ...
- Car Not Starting. ...
- Poor Fuel Economy. ...
How to reprogram control module?
Vital Symptoms That Call For Body Control Module Reset
- Burnt Fuse Box. The chief symptom that calls for Body Control Module reset is the burnt or overheated fuse box. ...
- Jerking Or Shaking. The car starts to produce jerks and shakes if the BCM is not in good condition. ...
- Jammed Electronic Supplies. Trouble inside the BCM system can cause problems to electronic circuits and supplies. ...
- Disturbed Pick-up. ...
How to upgrade a Powertrain Control Module (PCM)?
Changing the Program: Updating a PCM is easy with the right tools. Tool Briefing offers real-world tips and advice for using specific tools to accomplish specific tasks. The step-by-step tasks are shown below in the Identifix Direct-Hit box, along with related vehicles, concerns and factory bulletin numbers. But remember, the tool information ...
How can I test on the Powertrain Control Module?
What Are the Symptoms of a Bad Powertrain Control Module?
- Running Poorly. The PCM is what ultimately controls and regulates your fuel system. ...
- Will Not Run. In some cases, a PCM problem will cause the vehicle not to run at all. ...
- Dashboard Error Lights. If your PCM is malfunctioning, you can expect to see almost every error light imaginable appear and disappear at some point.
- Emissions. ...
What does it mean to reprogram powertrain control module?
A PCM reprogram may change the engine's idle speed, spark timing, and fuel mixture amongst other things. This brings the powertrain to the factory specification and should help it to operate as intended. Additionally, this is quite rare, but sometimes manufacturers will have software updates for your car's PCM.
How do I reprogram my Ford PCM?
6:3716:33How to Reprogram Ford PCM ECM reflash "Uninstall Install aftermarket ...YouTubeStart of suggested clipEnd of suggested clipWe're just going to go to module programming. And we're going to go to powertrain control module.MoreWe're just going to go to module programming. And we're going to go to powertrain control module. And what it's going to do is it will actually automatically check to see. If.
How much does it cost to reprogram powertrain control module?
Prices could range from $80 to $150, depending on the service location you choose. The process takes around about half an hour, but keep in mind that most auto-electricians charge you for at least one hour of work. PCM reprogramming is also one of the few times we'll recommend a dealership over an independent mechanic.
Can I reprogram my PCM myself?
PCMs are built with microchips that can be reprogrammed electronically without being removed from the vehicle. Reflashing is a process where you electronically transfer approved files from a vehicle manufacturer's website using a diagnostic connector.
Why would an engine powertrain computer module be reprogrammed?
Flashing or reprogramming a car's computer is one way to keep the vehicle's engine control modules up to date. This is commonly done on vehicles 1996 and newer to make sure the microprocessors in the power train and fuel injectors are regulating the system properly.
Why would a PCM need to be reprogrammed?
PCM Reprogramming may be required to resolve a hot or cold starting issue, idle roughness, stalling, or an emissions failure. Reprogramming is often used to modify the operation of emission functions so they have less of an effect on drivability.
How do I know if my powertrain control module is bad?
Symptoms of a Bad or Failing Engine Control Module (ECM)Check Engine Light Turns On.Engine Stalling or Misfiring.Engine Performance Issues.Car Not Starting.Poor Fuel Economy.
How can you tell if a PCM is bad?
What Are the Symptoms of a Faulty PCM?Your “check engine” light is on.Other warning lights may be on, including traction control and ABS.You lose fuel economy for no apparent reason.Your car stutters when starting, requires multiple attempts, or won't start at all.Stuttering or stalling during idling.More items...•
What causes powertrain control module failure?
Water is the primary element to avoid as exposure to it can render the PCM irreparable. Other environmental factors that could lead to PCM failure include thermal stress due to excessive heat and excessive vibration that causes sensitive parts to fail.
How do I reprogram my ECU at home?
0:471:55How to Reprogram Your Car's Computer - YouTubeYouTubeStart of suggested clipEnd of suggested clipReprogramming. What happens next is your computer is downloading all the new ford software when it'sMoreReprogramming. What happens next is your computer is downloading all the new ford software when it's done it passes that information through the reprogrammer.
Can I flash my own PCM?
Flash reprogramming PCMs is NOT for the feint of heart. First, you have to have a scan tool or J2534 device that can reprogram your vehicle's computer. Then you have to go to the vehicle manufacturer's service information website, pay an access fee and find the correct update for your vehicle.
Will disconnecting battery reset PCM?
A. It depends on the car's age and type of ECU used. On some older cars, disconnecting the battery will reset the system but in most new cars it does nothing, except potentially reset the clock and radio station presets.
What is powertrain control module reflashing?
What is Powertrain Control Module Reflashing? Powertrain Control Module reflashing is essentially a software upgrade. PCMs are built with microchips that can be reprogrammed electronically without being removed from the vehicle.
How much does it cost to replace a powertrain control module?
The cost of replacing your powertrain control module will be between $450 and $1,630. For labor, you can expect to pay between $45 and $125. Parts should cost you $400-$1,500.
How to reset a PCM?
Disconnect the negative battery cable from the battery. Use a wrench to loosen the lock nut, and pull the cable off. This cuts the power to the PCM. Wait for five minutes. Reconnect the negative battery cable to the battery and close the hood of the vehicle. The PCM is now reset.
What is the power train control module on a Ford?
The power train control module on a Ford controls every aspect of the vehicle's engine, transmission, clutch and electrical and fuel delivery. Without a properly working PCM, the Ford will not run. At times, you may want to perform a reset of the Ford PCM for basic troubleshooting. This can often resolve small issues that you may experience with the Ford.
How long does it take for a PCM to reset?
Wait for 20 minutes while the PCM bleeds off the electricity it stores for backup power. Once the power drains from the PCM, it resets.
What are the signs of PCM failure?
Signs of PCM failure may include engine light turning on, truck not starting, engine stalling while driving, or poor engine performance.
What to look for when inspecting PCM?
While you are inspecting the PCM, look for problems in the wiring and connectors. The wires should be fully insulated without any breaks. The connectors should be clean with no bent pins or connector blades.
Why Transmission Control Module Needs Resetting
In order to keep the transmission running at its optimum level, it is important that the Transmission Control Module is reset from time to time. The transmission will automatically make a calibration check before a reset and if it finds any errors, it will automatically carry out a reset.
Can I drive with bad ECM?
If the ECM were to become damaged or faulty, then it could spell trouble for the entire engine because it would not be managed properly. If the engine is not managed properly, then it is not going to operate properly and then your car won’t work properly.
What does reprogram reverse?
The reprogram reverses that, now default will be OFF till you decide to turn it ON.
What is an addendum to an owner's manual?
Additionally, an addendum to the owner’s manual supplement, recommending the owner conduct more frequent engine oil level checks, will be included with the owner letter mailing. The addendum is to be inserted in the owner’s manual.
What is the recall number for hatch?
It has nothing to do with the hatch recall which is a BCM reprogram and is recall 16C13.
What is the SAE standard for reprograming PCM?
To reprogram a PCM, the tool must comply with SAE Standard J2534-1. You can also use a J2534-2 pass thru tool that can reprogram other control modules as well as the PCM. Not all pass thru tools work on every vehicle, although some are more versatile than others.
What does a MAF reading on a Ford mean?
On the Ford described here, MAF readings are reported as voltage, and if the voltage isn’t correct at idle, that might indicate a vacuum leak. A good way to locate a vacuum leak is with a smoke machine.
Why is my PCM not initializing?
If battery voltage falls too low during that first start-up , the PCM may not initialize properly. This can cause problems that are nearly impossible to diagnose or fix. Choosing your connection is easy.
How many channels can a fuel trim graph show?
Some can graph multiple data channels, and scan tool software for laptop computers can graph up to eight channels at once. The scan tool will also show Mass Air Flow (MAF) sensor data.
What is a pass through device?
A pass thru device is quite literally a box that acts as a translator, allowing the PCM to communicate with a Microsoft Windows operating system. Pass thru tools are completely self-contained; some don’t even have an on/off button.
Can reprogramming a PCM be bad?
Reprogramming is a delicate operation requiring careful attention to detail. At best, getting it wrong will cost time. On some vehicles, a botched reprogramming operation can ruin the PCM. Throughout the reprogramming operation, battery voltage absolutely must remain constant. That’s why you need external power.
Can you reprogramme a PCM with a J2534?
The smoke is made from common baby oil, and when combined with ultraviolet dye, it’s one of the fastest ways to find a leak. Reprogramming a PCM requires a J2534 Pass Thru device. Only 2004 and newer vehicles can be reprogrammed.
Why is Ford recalling?
This recall stems from a transmission problem--specifically, an issue with the output speed sensor on the transmission's lead frame. The underlying problem appears rooted in the software associated with the powertrain control module, which could cause vehicles to downshift suddenly. According to Ford:
Does Ford replace the lead frame?
Ford says that dealers will inspect the powertrain control module and upgrade the software if there are no diagnostic trouble codes found. The upgrade will prevent the vehicles from downshifting into first gear if a fault with the output speed sensor takes place. Ford also says that it will replace the lead frame on vehicles that have logged fewer than 150,000 miles.
How to reset a Ford PCM?
You can either reset your FORD PCM through the fuse box or the simple yet effective way that is to just unplug the battery.
How to reset ECM?
One way is by disconnecting the battery cable for 2 to 3 minutes and waiting to see if the check engine light comes back on upon reconnecting the battery and start the car. ...
How to reset a car computer?
The 2 most common ways to reset your car computer is by either unplugging the battery or by resetting the fuse related to the engine control module
Why does the ECU learn about your driving habits?
Because your ECU learns about your driving habit constantly since it has the capacity to store tons of data including your trouble ...
Can an ECU be reset?
Yes, all ECU (Engine Control units) can be reset and be should reset once per manufacturer’s guideline for a smooth relearn process or upon installing a replacement unit.