How do you remove a Kwikset door knob cylinder?
- Expose hidden set screws.
- Use a screwdriver to remove the set screws, which will release the lock and lever from the opening.
- Look for pin holes in the rose or in the lever body itself.
- Use an Allen wrench to remove the lever.
- Examine the lever and look for slots or depressions.
Full Answer
How to repair a Kwikset door lock cylinder?
Things You'll Need
- Lock re-keying kit
- Paper clip
- Phillips-head screwdriver
- Needle-nose pliers
How do you remove a Kwikset door knob cylinder?
- Instructions.
- Use lock-picking tools legally to unlock your own door.
- Use a paper clip to firmly press into the knob hole, located on the side of knob.
- Separate the cylinder housing and use the retainer ring tool in the re-keying set to remove the retainer ring.
How to rekey a Kwikset doorlock or deadbolt?
The Pros
- The Kwikset Smart Key design uses wafers to interact with a sidebar. This design protects lockpicking and key bumping.
- The ability to rekey a Smart Key Lock without disassembly is a major convenience.
- You can accomplish rekeying without the need for a locksmith
How to rekey and reset a Kwikset SmartKey?
With the Kwikset Smart Key, you can rekey your locks, even without a good key, right in the door, in just 15 seconds.If rekeying the lock while still on the ...
How do you remove a Kwikset lock cylinder?
0:532:34How to remove the lock cylinder from a Kwikset SmartKey entry knobYouTubeStart of suggested clipEnd of suggested clipI push on it with my thumb. So I can do a small flat bladed screwdriver on the other end of the holeMoreI push on it with my thumb. So I can do a small flat bladed screwdriver on the other end of the hole. And you've all good push. The lock cylinder pops. Up.
How do I change the key cylinder on a Kwikset?
1:003:25(118) How to Remove the Cylinder from a Kwikset Door knob - YouTubeYouTubeStart of suggested clipEnd of suggested clipAnd with the camera up here you can see and then once that's all the way in that piece is held up.MoreAnd with the camera up here you can see and then once that's all the way in that piece is held up. Yeah. I should just tap it and the cylinder will come out.
How do you remove a Kwikset single cylinder deadbolt?
3:056:34[87] How to Remove Kwikset Deadbolt Without Screws!? - YouTubeYouTubeStart of suggested clipEnd of suggested clipGuys this little you know cutaway. And it has this little slot you can usually fit your fingernail.MoreGuys this little you know cutaway. And it has this little slot you can usually fit your fingernail. In there and pry it right off. And set it aside.
How do you remove a cylinder from a door lock?
0:148:24Locksmithing 101 Cylinder Removal - YouTubeYouTubeStart of suggested clipEnd of suggested clipPut the tool in spin. It. So it pushes that tab in then push it in a little more just like that thenMorePut the tool in spin. It. So it pushes that tab in then push it in a little more just like that then turn the spindle. And pull it straight up and out.
How do I replace a Kwikset tumbler?
3:216:10How to Rekey a Pin and Tumbler Knob - YouTubeYouTubeStart of suggested clipEnd of suggested clipParts turn the lock upside down and tap the pickle fork lightly on a hard surface the cylinderMoreParts turn the lock upside down and tap the pickle fork lightly on a hard surface the cylinder should pop out easily. Using the forked end of the tool disengage.
How do you remove a tumbler from a deadbolt?
1:584:31How to Remove Cylinder from Key-in-Knob | Mr. Locksmith™ VideoYouTubeStart of suggested clipEnd of suggested clipAnd you can tell when you get it right the latch will be pulled in you turn it depress the retainer.MoreAnd you can tell when you get it right the latch will be pulled in you turn it depress the retainer. Again we depress the retainer not a lot of force. And then we pull the knob. Off.
How do you remove a deadbolt that has no screws?
0:223:47Remove BRINKS Deadbolt with hidden screws - FAST & EASY!YouTubeStart of suggested clipEnd of suggested clipFrom here you just have to pull this actual handle off with equal pressure you want to pull thisMoreFrom here you just have to pull this actual handle off with equal pressure you want to pull this knob off and I may need both hands. And just by wiggling it.
How do you remove a lock cylinder without a key?
Take your screwdriver and insert it into the ignition lock cylinder. Turn it as far round in a clockwise direction that you can. Then pull the paperclip to the right as much as you can. You should then be able to slide the switch out easily.
How do you remove a cylinder head?
0:534:21HOW TO REMOVE CYLINDER HEAD GASKET. DOES IT MATTER THE ...YouTubeStart of suggested clipEnd of suggested clipYou don't use the special boat sequence and torque specs. You're going to put. Not even amount ofMoreYou don't use the special boat sequence and torque specs. You're going to put. Not even amount of pressure on one side of the head you can damage.
How do you take apart a Kwikset Handleset?
1:079:48How to Replace an Old Entry Door Handle with a Kwikset Smartkey ...YouTubeStart of suggested clipEnd of suggested clipItself just need to unscrew. Those i'm using a drill because it's a little bit faster you of courseMoreItself just need to unscrew. Those i'm using a drill because it's a little bit faster you of course can use a normal hand screwdriver if you like.
How to rekey a Kwikset lock?
The best way to remove cylinders is with the appropriate plug removal tool and plug follower. A removal tool is designed to remove specific parts of the locking mechanism. The follower is a tube the same diameter as the cylinder plug. The follower pushes the cylinder through the lock and fills the area that the cylinder fits into.
How to push a cylinder out of a lock?
Insert a plug follower on the end of the cylinder and slowly push the cylinder out of the lock with the plug follower. A plug follower is a tube that is the same diameter as the cylinder you are pushing out of the lock.
How to remove a lock from a plug?
Hold the cylinder side of the lock in your hand with the inside of the lock facing you. Remove the clip on the side of the plug with a flat-head screwdriver or plug-removal tool. The clip will release from the plug as you move the clip side to side.
How many screws are on a deadbolt?
Usually there are two screws on the inside portion of the deadbolt lock face. Remove those two screws and the deadbolt will pull away from both sides of the door. The bolt mechanism does not need to be removed.
What is a follower in a cylinder?
The follower is a tube the same diameter as the cylinder plug. The follower pushes the cylinder through the lock and fills the area that the cylinder fits into. Advertisement.
Product Overview
As the industry leader, Kwikset has provided trusted security for over 60-years and has become synonymous with security, peace of mind, style and innovation.
Info & Guides
You will need Adobe® Acrobat® Reader to view PDF documents. Download a free copy from the Adobe Web site.