PolyGone reacts chemically with the polymer and breaks it down (depolymerizes) so it can be rinsed away without damage to the surface/substrate. This depolymerization prevents re-deposition of the reaction by-products and allow for water rinsing.
Full Answer
What is Polygone depolymerization?
This depolymerization prevents re-deposition of the reaction by-products and allow for water rinsing. PolyGone completely removes 100% of the sealant which offers significant advantages over other removal methods that require scraping and typically results in damage to the substrate.
How to remove RTV from polysulfide?
Both polysulfide and silicone RTV are difficult to remove completely since they actually bond into surface/substrate. PolyGone reacts chemically with the polymer and breaks it down (depolymerizes) so it can be rinsed away without damage to the surface/substrate.
What is Polygone™ stripping?
PolyGone™ stripping agents are unique formulations that remove cured polysulfide (PRC) and silicone RTV sealants from metal, ceramic, and some plastic substrates. PolyGone works at room temperature and does not contain flammable, chlorinated or odorous solvents.
How to remove polymeric sand from paving slabs?
To begin, avoid any contact with water or moisture before cleaning. It will be easier to remove the polymeric sand from the surface while it’s dry. Sweep the surface with a broom with soft bristles. So that you don’t scratch or damage the surface of the pavers. Repeat step two as many times as necessary to remove as much polymeric sand as possible.
What is polygone stripping?
PolyGone™ stripping agents are unique formulations that remove cured polysulfide (PRC) and silicone RTV sealants from metal, ceramic, and some plastic substrates. PolyGone works at room temperature and does not contain flammable, chlorinated or odorous solvents.
Does polygone remove sealant?
PolyGone completely removes 100% of the sealant which offers significant advantages over other removal methods that require scraping and typically results in damage to the substrate. There are also products that try to “dissolve” the sealants but due to their inertness, this does not work.
How to dispose of polygone?
Diluted PolyGone can be disposed of by discharge to a sewage treatment plant with prior approval. Used PolyGone may need to be disposed of as organic solvent waste depending on the sealants and contaminates removed. PolyGone has a high BTU value and waste can be managed through a fuels-blending program.
How to store Polygone 305?
STORAGE: PolyGone 305 must be stored in a cool and dry environment away from light and incompatible materials. The recommended storage temperature is between 50ºF-80ºF (10ºC-27ºC).
What is polysulfide used for?
In the marine environment, polysulfide is used to seal teak decks, fuel systems, and through-hulls. CHEMISTRY: PolyGone 305 is a proprietary formulation designed to penetrate, break down, and emulsify tenacious sealants. Once broken down, the sealant is suspended to prevent re-deposition and enable easy rinsing.
What is a polygone 305?
DESCRIPTION: PolyGone 305 is a high performance Industrial / Marine Grade polysulfide sealant depolymerizer / emulsifier designed to remove cured polysulfide and other sealants from a variety of surfaces. Polysulfide’s primary industrial application is in window (fenestration) industry where is it used to create the long lasting seal between double and triple pane window units. In the marine environment, polysulfide is used to seal teak decks, fuel systems, and through-hulls.
What temperature is Polygone 305?
APPLICATION: PolyGone 305 is intended for use at room temperature (68°F-80°F). It may be continuously sprayed or used in immersion-based cleaning systems. Heat (120ºF/49ºC) and/or gentle agitation, including ultrasonic, is not necessary but significantly enhances performance.
Is Polygone 305 metal friendly?
COMPATIBILITY: PolyGone 305 is metal-friendly. The formulation is non-ionic and non-reactive. Metals such as Cu, Fe, Al, Zn, and Ti have been tested with PolyGone 305 with no detected metal loss. However, PolyGone 305 attacks many types of polymers and plastics.
Is Polygone 305 water soluble?
RINSE: PolyGone 305 is water-soluble. Although water may be used to rinse the product, rinsing with a mild cleaner such as eOx®, also available from RPM Technology, followed by pure water will improve removal of all residues.
Can you pressure wash polymeric sand?
Can You Pressure Wash It? Yes, you can use a pressure washer but strictly if necessary. If it’s not possible to remove the hardened polymeric sand after a few days washing the surface, then you can bring on the “big guns.”. The essential when using pressure wash is not to remove the polymeric sand between the joints.
Can you wash polymer sand off?
But, especially if the polymeric sand layer is thick, it forms rough clumps over the surface. Probably, you won’t be able to wash it off just with hose water. Pressure washing before sealing is actually really important.
Can you clean polymeric sand off pavers?
But, you can still clean the flooring surface after that.
Why is it important to familiarize yourself with polymeric sand?
There are universal steps to the process of installing polymeric sand, failure signs, and ways in which you can ensure that your polymeric sand installation will run smoothly.
What does it mean when sand is polymeric?
If there is a crust forming on the surface of the sand, typically this means that the sand was filled too high or the sand was not watered enough. If the sand was filled too high in the initial installation, the sand will continuously be worn and eroded away.
What is polymeric sand?
Polymeric sand is a sand formula that is swept into the joints of pavers and natural stone to lock in the product, prevent weed growth and insects, and to provide the final touches of any hardscaping job.
How far should you sweep polymeric sand?
Most manufacturers recommend not to sweep the sand more than 10 feet in any direction to avoid separating the delicate formula.
What should not be installed on pavers?
What should not be installed is stone dust or chip dust. That is because this will harden and not allow water to drain through, keeping the water below the pavers and saturating the joints, not allowing the polymeric sand to properly dry and never set.
Is polymeric sand a failure?
Polymeric sand installations are not without their problems. Following the instructions is the first step to ensuring there is no failure. However, mistakes happen and there are problems with some installations. Let’s get into some of the problems and the solutions to those problems.
Can you run a plate compactor over a stone?
Compacting. Once you have swept the sand into all of the joints, you can run a plate compactor over the surface of the stones. Unless your stone is a tumbled product (even still we would recommend this), you should have a protective barrier between your plate compactor and the pavers.