Driveway Material Cost Per Square Foot Estimate
| Concrete | $3 - $18 |
| Asphalt/Blacktop | $7 - $13 |
| Gravel | $1 - $3 |
| Chip Seal | $2 - $5 |
| Heated | $12 - $21 |
How much does is cost to pave a driveway?
I will break the costs down to explain why.
- Let us work on an average driveway size which could be 15 m long by 6 m wide. ...
- A very good price to pay for bevel paving bricks is around R 110 per m² ex Factory
- In my scenario I am pretending the site is 10 km from the Factory.
- Getting the paving to site would mean I would have to hire a delivery truck to get the approximately 4000 bricks there. ...
How much is driveway paving?
Driveway Paving Cost per Square Foot. The average driveway pavement cost homeowners pay is between $8 and $25 per sq.ft. with labor included. While most projects are charged per sq.ft. some contractors charge by the hour at a rate of $25 to $60 per hour. These are limited to smaller projects and upgrades or repairs.
How do you calculate the cost of a concrete driveway?
Upgrading a gravel driveway to a concrete driveway:
- Grading the existing drive and removing some material, if necessary for proper height
- Installation and finish of 4-6 inches of reinforced concrete
- Application of sealer
- Cost: $3.40 to $5.25 per square foot using 4 inches of concrete
- Cost: $4.35 to $6.50 per square foot using 6 inches of concrete
What is the average cost of concrete driveway?
The average cost of a concrete driveway, by comparison, is almost $7,400. Other sources estimate the cost to install an asphalt driveway to be between $2,300 and $10,300. Homeowners typically pay per square foot.
How much is a 700 ft driveway?
For a larger driveway or thicker base, the cost will be higher. For example, a driveway 15 feet wide by 700 feet long with a six inch base will need approximately 25 tons of gravel, at a material cost of about $700. With delivery, the total cost will be around $1000.
Is it cheaper to pave or concrete a driveway?
As far as installation costs and concrete costs go, poured concrete is technically the most affordable per square foot. However, even though the upfront cost of pavers is higher, concrete pavers offer greater value and durability than poured concrete and stamped concrete.
Is it cheaper to pave or gravel a driveway?
A gravel driveway is a more budget-friendly option than paving with concrete, which runs from $4 to $15 per square foot.
How do you calculate the cost of an asphalt driveway?
For the simplest estimate, you can use this formula.Length x width=Square footage of the driveway.Driveway sq ft x $3= low end cost.Driveway sq ft x 7= high end cost.Driveway sq ft x $2= low end cost.Driveway sq ft x $4= high end cost.When to reseal your driveway:When to repave your driveway:
How much does it cost to pour a 24x24 slab of concrete?
A typical 24x24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
Do pavers increase home value?
Aside from this, how the pavers are used will also make a difference. For example, a great patio could add as much as $15,000 to the average home's price. However, if you are using pavers as part of creating a brand new garden space, you could improve your home's value by as much as 20 percent.
What type of driveway lasts the longest?
ConcreteConcrete is the old standby for driveways. Most suburban homes opt for this material for two big reasons: Concrete is typically the longest-lasting driveway surface, and, if installed properly, it is practically maintenance-free.
What is the life expectancy of a driveway?
The average life of your concrete driveway will depend on installation methods, environmental conditions and temperatures. However, you can expect your surface to last anywhere from 25 to 30 years with proper care. The key to prolonging the life of your investment is to pay attention to wear and tear each season.
What is the best driveway to have?
Concrete. Among the most durable options on the market is a concrete driveway surface. Although it provides a hard and stable surface, that is highly dependant on professional installation, high upfront costs, maintenance, and weather conditions.
Is concrete driveway better than asphalt?
Overall, asphalt is less durable than concrete. With proper maintenance, it can last 30 years. Alternatively, concrete provides a sturdy, long-lasting option and can last homeowners 50+ years with occasional repairs and degreasing.
How thick should a asphalt driveway be?
2 to 3 inchesResidential driveways typically use 2 to 3 inches of asphalt with 3 being suitable for occasional large trucks or heavy equipment. Underneath the asphalt you should have 6 to 8 inches of granular base aggregate.
Is asphalt the same as blacktop?
Blacktop is heated to approximately 150 degrees celsius, whereas asphalt is only heated to 120 degrees celsius. Asphalt is has a higher bitumen content and for that reason is less porous and more resilient to wear and tear from high traffic and thus is the preferred choice for major highways.
Cheapest Driveway Material?
Gravel is by far the cheapest driveway material and one of the longest-lasting materials with a lifespan of 100 years. It still needs regular maint...
How Long Does a Driveway Last?
Driveways typically last around 30 years total, but some need more maintenance than others. Asphalt and concrete driveways need maintenance every f...
How Much Value Does a New Driveway Add?
On average a new driveway can add between $5,000 to $7,000 in added home value. Of course, that value depends upon the size of your driveway.
Which is Cheaper? Concrete or Asphalt Driveway?
Asphalt runs slightly cheaper than concrete with an average square foot cost of $3 to $7 but it won’t last as long as concrete. A concrete driveway...
How Long to Wait Before Driving on New Driveway?
It’s typically recommended that you stay off a new asphalt driveway for 24 hours, longer if it’s humid out. If you have a concrete driveway, you’ll...
How Often Should You Seal a Driveway?
Professionals recommend resealing an asphalt driveway every three to five years but it could be sooner depending upon the state of your driveway. P...
How much does it cost to pave a driveway?
While gravel and asphalt together cost around $4.50 a square foot in materials, the labor to pave the driveway will cost around $5 to $7 a square foot , depending on the complexity of the job.
How much does gravel cost?
Gravel. Gravel is the least expensive material you can use for your driveway, costing between $1 and $2 a square foot. In warm climates, it can last for decades with little maintenance. But in areas that see snowfall, plows and shovels can disturb the gravel, and pieces of rock can damage snowblowers.
What is tar and chip driveway?
Chip-sealed driveways, also called tar-and-chip, are a way to make asphalt driveways more durable and longer-lasting. A layer of asphalt is put down first, then a layer of aggregate is put on top and compacted into the tar.
What is interlocking pavers?
Interlocking Pavers. Interlocking pavers are one of the most durable and attractive forms of driveway paving. The pavers can be made of concrete, stone, brick, or composites and come in many shapes, sizes, and colors. Therefore, it is possible to create very interesting and unique designs.
What is the maintenance of a driveway?
Maintenance. Maintenance for driveways depends a lot on the climate you live in and the type of driveway. For both asphalt and concrete driveways, pay attention to cracks, frost heaves, and other structural problems with the material.
Why is it important to have a driveway freshly paved?
Having your driveway freshly paved will not only make your property look better, but it will also help prevent damage due to potholes and other issues inherent with older driveways.
How much does stamped concrete cost?
Stamped concrete is an attractive way to add color and design to a driveway. It costs around $8 to $12 a square foot, and multiple patterns and colors are available, which allows for customization. Like poured concrete, it does better in hot climates than cold climates and can be expensive and difficult to repair.
Compare Quotes From Top-rated Local Flooring Contractors
The average costs to pave a driveway range between $3 and $15 per square foot. The cost depends on materials, size of the driveway and installation requirements. Expensive materials can cost as much as $30 per square foot while cheaper materials are as low as $1 per square foot.
Driveway Cost Per Square Foot
The cost of driveway installations is typically determined by the driveway site’s square footage. While the material itself and the installation cost affect the price per square foot, the square footage of a driveway will sum the total cost of the project.
Driveway Cost By Material Type
Depending on the material, paving a driveway can cost anywhere from $1,500 to over $11,000. Concrete is a popular choice because of its durability and long-lasting nature. Other popular types of driveways include asphalt or blacktop, gravel, pavers and rubber.
Driveway Installation Cost
The total cost of driveway installation depends on the size of the driveway, site conditions and the material used. Labor can make up about half of the total price per square foot while the price for new material can make up the other half. Thickness can affect material cost, especially for concrete and asphalt.
Frequently Asked Questions
Gravel is the least costly material to pave a driveway. The price ranges from $1 to $3 per square foot. The average total cost is usually around $1,200, though this number may not account for the fact that gravel is usually used to pave much larger driveways as a cost-reduction solution.
Driveway Costs
A new driveway can add some curb appeal and more. It comes with a cost and a commitment for a few days to get the project done. A driveway costs between $1,700 to $7,000 for materials and averages $4,500. Expect to pay between $2 and $15 per square foot for materials and installation.
Driveway Cost Per Square Foot
The cost of a driveway will depend upon the condition of your current driveway, its size and the material you want to use. Gravel is the cheapest material to use at just $1 to $3 per square foot while a heated driveway is the most expensive at $12 to $18 per square foot.
Driveway Cost by Material
A gravel driveway is the cheapest way to go and it’ll last more than 100 years with regular maintenance. But it’s not attractive to every homeowner and tends to kick up dust on vehicles. Concrete driveways remain a low-cost option because they come in slightly cheaper than an asphalt driveway and often require less maintenance.
Driveway Construction Cost
Building a driveway will cost around $3 to $12 on average, depending upon the size of the driveway and the selected material. Expect to pay as much in labor as you do for materials. Labor costs can increase if the driveway needs leveling, too.
When to Build a Driveway
Depending upon your climate, summer is likely the best time to build a driveway. Plan when there are a few clear days of moderate temperatures. Installing an asphalt driveway is dirty work and you need a few days of clear skies to get it done.
Frequently Asked Questions (FAQs)
Gravel is by far the cheapest driveway material and one of the longest-lasting materials with a lifespan of 100 years. It still needs regular maintenance and dust suppression.
How To Estimate Driveway Paving Cost?
Driveway paving cost for installation depends on the square footage of the site and the type of material used.
Estimated driveway paving cost
A driveway paving project can cost anywhere from $1,600 to $21,600 and can range between those numbers. In summary, the factors to consider when calculating the total cost of a driveway project are the size, shape, slope, and location. The more details you have about the dimensions of your property, the more accurate your estimate will be.
How much does it cost to build a driveway?
The cost to build a driveway ranges from $600 to $18,000, depending on the material. The cheapest driveways cost $1 to $3 per square foot for gravel, while standard concrete and asphalt driveways cost $3 to $8 per square foot.
How much does it cost to install a concrete driveway?
Concrete driveway. Installing a concrete driveway costs $2,400 to $4,800 on average or $4 to $8 per square foot for plain gray concrete. Adding decorative colors, borders, stamped patterns, and finishes costs $8 to $18 per square foot. Concrete lasts 30 to 40 years and handles hot climates better than asphalt.
How long does a concrete driveway last?
Asphalt driveways last 15 to 30 years, and concrete driveways last 30 to 40 years on average, depending on the climate and usage. Brick and stone pavers last 25 to 50 years. A cobblestone or gravel driveway lasts up to 100 years if well-maintained.
What is the cheapest driveway material?
The cheapest driveway material is gravel at $1 to $3 per square foot using aggregate made of crushed shells, crushed concrete or asphalt, or pea gravel . Tar and chip seal driveways are the second cheapest at $2 to $5 per square foot.
How much does gravel cost?
Well-built gravel driveways require light raking and new gravel once or twice a year. Gravel prices range from $10 to $50 per ton, depending on the stone size and type.
How much does an exposed aggregate driveway cost?
Exposed aggregate or pebble finish driveways cost $5 to $11 per square foot or $3,000 to $6,600 on average. Exposed aggregate features stones mixed into concrete or seeded on the surface. Natural aggregates provide a textured, nonskid surface in various colors, including pastels, earth tones, and deep reds and blues.
How much does a chip seal driveway cost?
Chip seal driveways cost $1,200 to $3,000 or $2 to $5 per square foot. Chip seal, also called tar and chip, lasts 7 to 10 years. Tar and chip driveways have the durability of blacktop, come in various colors, and feature layers of stone aggregate spread over hot liquid asphalt.
How much does it cost to pave a road?
Cost to pave an asphalt road. The average cost to pave a private one-lane asphalt road is $35 to $85 per linear foot. Paving a two-lane (24'-wide) asphalt road costs $70 to $170 per linear foot or $370,000 to $900,000 per mile. Blacktop road construction costs more than driveways because roads need 5" to 11" thick asphalt.
How much does it cost to pave a parking lot?
Cost to pave an asphalt parking lot. Paving an asphalt parking lot costs $3 to $7 per square foot, not including marking, striping, curbing, or permits. Paving a 10-car asphalt parking lot costs $9,000 to $21,000 on average or $900 to $2,100 per space of 300 square feet.
How thick should a driveway be?
A new residential driveway needs 3 to 5 inches of asphalt over 4 to 8 inches of rock-base foundation to withstand temperature changes and last 20+ years. Some companies recommend a 2" thickness to save $0.50 to $1 per square foot, but won't provide a warranty due to deterioration risks.
How much does it cost to repave an asphalt driveway?
The average cost to repave an asphalt driveway is $4 to $10 per square foot with a new gravel base or $3 to $7 per square foot with an existing base. Repaving a 2-car (20’x20’) asphalt driveway costs $1,600 to $4,000 on average. Repaving includes removing and hauling away the existing asphalt.
How long does asphalt last?
An asphalt driveway lasts 15 to 30 years and requires sealcoating every 3 to 5 years. Boosts curb appeal and resale value. A new asphalt driveway needs an asphalt layer 3" to 5" thick to last. Resurfacing only the top layer or asphalt overlay costs $1 to $3 per square foot.
How much does stamped asphalt cost?
Colored or stamped asphalt costs $5 to $15 per square foot for a new driveway or replacement, or $3 to $8 per square foot for resurfacing the top layer. A 20x20 stamped asphalt driveway costs $2,400 to $6,000. Decorative patterns are sealcoated, which colors and protects the surface.
How much does it cost to lay asphalt over concrete?
Laying new asphalt over a concrete driveway costs $1 to $3 per square foot. Contractors fill cracks with concrete-repair caulk before paving. Resurfacing concrete with asphalt is cheaper than replacing concrete. However, special preparation is required to stabilize the concrete and prevent cracks.
How much does a brick driveway cost?
A brick driveway costs $10 to $25 per square foot on average, or between $5,500 and $14,500 for materials and installation. Brick paver driveway prices depend on the strength rating, clay type and firing method, size, finish, and color.
How much does it cost to install pavers?
The labor cost to install pavers is $6 to $10 per square foot.
How long does a paver driveway last?
A paver driveway lasts 25 to 75 years, depending on the quality of installation work, the types of pavers, the maintenance steps taken, and the local weather. Compare this to a concrete driveway that lasts 20 to 30 years on average.
How much does porcelain paver cost?
A porcelain paver driveway costs $15 to $30 per square foot for materials and installation. Porcelain is stronger, lighter, and easier to install than natural stone or concrete pavers. With a low water absorption rate of 0.1 to 0.5%, porcelain doesn’t crack easily.
How much does it cost to install a concrete block driveway?
An average concrete block paving driveway costs $10 to $20 per square foot or between $5,500 to $11,500 for materials and installation. The price of concrete driveway pavers depends on the size, thickness, design, strength, and color.
How much does a paver base cost?
The cost of driveway sub-base and paver materials is $4 to $20 per square foot on average, which includes the gravel and crushed stone, fabric, sand, and edging. A driveway’s paver base must be a minimum thickness of 6 to 12 inches depending on the soil composition and drainage.
How much does it cost to install interlocking pavers?
Interlocking brick pavers cost $10 to $25 per square foot to install on average. Interlocking pavers have various design patterns, such as herringbone, basketweave, or running bond. Some pavers also have grooves to assist in "locking" the joint space between them once laid.
How much does it cost to pave a driveway?
Paving an asphalt driveway costs $4,746 on average, with a typical range between $2,935 and $6,567 . This project runs $7 to $13 per square foot, including $2 to $6 per square foot for materials and $5 to $7 per square foot for labor. If you need replacement, you’ll pay $8 to $15 per square foot. Although driveways are the most common use of asphalt in the home, other applications include:
How much does an asphalt driveway cost per square foot?
At $13 per square foot, curbs run more because of extra labor and a higher average thickness for the material. The width of the average residential lot is 75 to 125 feet. "Provided it's installed properly, including a stable base, and is well-maintained over time, an asphalt driveway should last twenty years or longer.".
How much does it cost to seal asphalt?
Stamped or colored asphalt costs $12 to $17 per square foot for the entire surface. If you only need the top coat, you’ll pay $5 to $10 per square foot. Asphalt in a unique shape or color adds interest to your property. In most cases, you’ll want to seal it to keep it in good condition for longer.
How much does asphalt overlay cost?
Asphalt Overlay Cost. Asphalt overlay costs $3 to $7 per square foot for standard materials. This project, often called a “top coat,” runs less because it involves a thinner layer on top of an existing surface. Asphalt sealant costs about $500, and should be done at least 6 months after the top coat.
How much does it cost to pave a 100 foot path?
Paving a 100-foot asphalt path costs $1,750 to $3,250. The average pathway is about 30 inches wide. Designs with complicated curves increase the total because they add to the square footage.
How much does reclaimed asphalt cost?
Recycled or Reclaimed Asphalt. Recycled or reclaimed asphalt costs $10 to $20 per ton, compared to $100 to $200 per ton for new. This can save you $675 to $1,350 on materials for a driveway, if it’s available in your area.
How many square feet does a ton of asphalt cover?
One ton usually covers 40 to 80 square feet. The amount you need depends on the thickness of the layers: 2 inches thick: 80 square feet per ton. 4 inches thick: 40 square feet per ton. For the average driveway, you’ll need 7.5 to 15 tons. "The complexity of the job itself weighs heavily on the price of an asphalt job.